• Energy Research
• 7. Clean energy close
• US close
• CA close
• English close

Leaching dataset of dissolved organic carbon (DOC) and nitrogen (DON), nitrate (NO3+) and ammonium (NH4+) were collected from 6 cropping treatments (corn, switchgrass, miscanthus, native grass mix, restored prairie and poplar) established in the Bioenergy Cropping System Experiment (BCSE) which is a part of Great Lakes Bioenergy Research Center (www.glbrc.org) and Long Termn Ecological Research (LTER) program (www.lter.kbs.msu.edu). The site is located at the W.K. Kellogg Biological Station (42.3956° N, 85.3749° W and 288 m above sea level), 25 km from Kalamazoo in southwestern Michigan, USA. Prenart soil water samplers made of Teflon and silica (http://www.prenart.dk/soil-water-samplers/) were installed in blocks 1 and 2 of the BCSE (Fig. S1), and Eijkelkamp soil water samplers made of ceramic (http://www.eijkelkamp.com) were installed in blocks 3 and 4 (there were no soil water samplers in block 5). All samplers were installed at 1.2 m depth at a 45° angle from the soil surface, approximately 20 cm into the unconsolidated sand of the 2Bt2 and 2E/Bt horizons. Beginning in 2009, soil water was sampled at weekly to biweekly intervals during non-frozen periods (April to November) by applying 50 kPa of vacuum for 24 hours, during which water was collected in glass bottles. During the 2009 and 2010 sampling periods we obtained fewer soil water samples from blocks 1 and 2 where Prenart lysimeters were installed. We observed no consistent differences between the two sampler types in concentrations of the analytes reported here. Depending on the volume of leachate collected, water samples were filtered using either 0.45 µm pore size, 33-mm-dia. cellulose acetate membrane filters when volumes were <50 ml, or 0.45 µm, 47-mm-dia. Supor 450 membrane filters for larger volumes. Samples were analyzed for NO3-, NH4+, total dissolved nitrogen (TDN), and DOC. The NO3- concentration was determined using a Dionex ICS1000 ion chromatograph system with membrane suppression and conductivity detection; the detection limit of the system was 0.006 mg NO3--N L-1. The NH4+ concentration in the samples was determined using a Thermo Scientific (formerly Dionex) ICS1100 ion chromatograph system with membrane suppression and conductivity detection; the detection limit of the system was similar. The DOC and TDN concentrations were determined using a Shimadzu TOC-Vcph carbon analyzer with a total nitrogen module (TNM-1); the detection limit of the system was ~0.08 mg C L-1 and ~0.04 mg N L-1. DON concentrations were estimated as the difference between TDN and dissolved inorganic N (NO3- + NH4+) concentrations. The NH4+ concentrations were only measured in the 2013-2015 crop-years, but they were always small relative to NO3- and thus their inclusion or lack of it was inconsequential to the DON estimation. Leaching rates were estimated on a crop-year basis, defined as the period from planting or emergence of the crop in the year indicated through the ensuing year until the next year’s planting or emergence. For each sampling point, the concentration was linearly interpolated between sampling dates during non-freezing periods (April through November). The concentrations in the unsampled winter period (December through March) were also linearly interpolated based on the preceding November and subsequent April samples. Solute leaching (kg ha-1) was calculated by multiplying the daily solute concentration in pore-water (mg L -1) by the modeled daily drainage rates (m3 ha-1) from the overlying soil. The drainage rates were obtained using the SALUS (Systems Approach for Land Use Sustainability) model (Basso and Ritchie, 2015). SALUS simulates yield and environmental outcomes in response to weather, soil, management (planting dates, plant population, irrigation, nitrogen fertilizer application, tillage), and crop genetics. The SALUS water balance sub-model simulates surface run-off, saturated and unsaturated water flow, drainage, root water uptake, and evapotranspiration during growing and non-growing seasons (Basso and Ritchie, 2015). Drainage amounts and rates simulated by SALUS have been validated with measurements using large monolith lysimeters at a nearby site at KBS (Basso and Ritchie, 2005). On days when SALUS predicted no drainage, the leaching was assumed to be zero. The volume-weighted mean concentration for an entire crop-year was calculated as the sum of daily leaching (kg ha-1) divided by the sum of daily drainage rates (m3 ha-1). Weather data for the model were collected at the nearby KBS LTER meteorological station (lter.kbs.msu.edu). Leaching losses of dissolved organic carbon (DOC) and nitrogen (DON) from agricultural systems are important to water quality and carbon and nutrient balances but are rarely reported; the few available studies suggest linkages to litter production (DOC) and nitrogen fertilization (DON). In this study we examine the leaching of DOC, DON, NO3-, and NH4+ from no-till corn (maize) and perennial bioenergy crops (switchgrass, miscanthus, native grasses, restored prairie, and poplar) grown between 2009 and 2016 in a replicated field experiment in the upper Midwest U.S. Leaching was estimated from concentrations in soil water and modeled drainage (percolation) rates. DOC leaching rates (kg ha-1 yr-1) and volume-weighted mean concentrations (mg L-1) among cropping systems averaged 15.4 and 4.6, respectively; N fertilization had no effect and poplar lost the most DOC (21.8 and 6.9, respectively). DON leaching rates (kg ha-1 yr-1) and volume-weighted mean concentrations (mg L-1) under corn (the most heavily N-fertilized crop) averaged 4.5 and 1.0, respectively, which was higher than perennial grasses (mean: 1.5 and 0.5, respectively) and poplar (1.6 and 0.5, respectively). NO3- comprised the majority of total N leaching in all systems (59-92%). Average NO3- leaching (kg N ha-1 yr-1) under corn (35.3) was higher than perennial grasses (5.9) and poplar (7.2). NH4+ concentrations in soil water from all cropping systems were relatively low (<0.07 mg N L-1). Perennial crops leached more NO3- in the first few years after planting, and markedly less after. Among the fertilized crops, the leached N represented 14-38% of the added N over the study period; poplar lost the greatest proportion (38%) and corn was intermediate (23%). Requiring only one third or less of the N fertilization compared to corn, perennial bioenergy crops can substantially reduce N leaching and consequent movement into aquifers and surface waters. readme files are given that describe the data table

This data set is no longer current – The most current data and all historical data sets can be found at https://data.nrel.gov/submissions/244 This database represents a list of community solar projects identified through various sources as of Dec 2021. The list has been reviewed but errors may exist and the list may not be comprehensive. Errors in the sources e.g. press releases may be duplicated in the list. Blank spaces represent missing information. NREL invites input to improve the database including to - correct erroneous information - add missing projects - fill in missing information - remove inactive projects. Updated information can be submitted to the contact(s) located on the current data set page linked at the top.

Comprehensive and reliable information on anthropogenic sources of greenhouse gas emissions is required to track progress towards keeping warming well below 2°C as agreed upon in the Paris Agreement. Here we provide a dataset on anthropogenic GHG emissions 1970-2019 with a broad country and sector coverage. We build the dataset from recent releases from the “Emissions Database for Global Atmospheric Research” (EDGAR) for CO2 emissions from fossil fuel combustion and industry (FFI), CH4 emissions, N2O emissions, and fluorinated gases and use a well-established fast-track method to extend this dataset from 2018 to 2019. We complement this with information on net CO2 emissions from land use, land-use change and forestry (LULUCF) from three available bookkeeping models.

Batteries have the potential to significantly reduce greenhouse gas emissions from on-road transportation. However, environmental and social impacts of producing lithium-ion batteries, particularly cathode materials, and concerns over material criticality are frequently highlighted as barriers to widespread electric vehicle adoption. Circular economy strategies, like reuse and recycling, can reduce impacts and secure regional supplies. To understand the potential for circularity, we undertake a dynamic global material flow analysis of pack-level materials that includes scenario analysis for changing battery cathode chemistries and electric vehicle demand. Results are produced regionwise and through the year 2040 to estimate the potential global and regional circularity of lithium, cobalt, nickel, manganese, iron, aluminum, copper, and graphite, although the analysis is focused on the cathode materials. Under idealized conditions, retired batteries could supply 60% of cobalt, 53% of lithium, 57% of manganese, and 53% of nickel globally in 2040. If the current mix of cathode chemistries evolves to a market dominated by NMC 811, a low cobalt chemistry, there is potential for 85% global circularity of cobalt in 2040. If the market steers away from cathodes containing cobalt, to an LFP-dominated market, cobalt, manganese, and nickel become less relevant and reach circularity before 2040. For each market to benefit from the recovery of secondary materials, recycling and manufacturing infrastructure must be developed in each region. This data was collected through various sources, including from EV Volumes, International Energy Agency, Argonne National Lab, and published articles. A model was created with R to process the data.  R is required to open the models.

Decarbonization of the transportation sector is particularly difficult due to its near-complete reliance on refined fossil fuels at present. In this paper, we describe the energy needs of the main transportation sectors worldwide: road transportation, aviation and maritime shipping. There is a growing commitment to electrification as the dominant decarbonization pathway. While deep electrification is promising (if by no means a certainty) for road transportation in wealthy countries, it will face steep obstacles in other sectors and in the developing world. Transportation decarbonization will require decoupling emissions from economic growth, highlighting the need for both accelerated technology innovation as well as creativity and cooperation in governance. The menu of policy options is replete with grim tradeoffs, particularly as the primacy of energy security and reliability (over emissions abatement) has once again been demonstrated in Europe and elsewhere. Aggregated vehicle ownership, emissions and electricity generate data for Countries and regions, worldwide.

Six nitroguanidyl-functionalized nitrogen-rich compounds were synthesized and characterized by EA, FT-IR, 1H NMR and 13C NMR. In addition, the crystal structures of ANPTz, CABNG and FANG were further determined by X-ray single crystal diffractometer. The thermal decomposition behaviours were studied by DSC-TG-FTIR-MS coupling technique and the results showed that all the compounds had good thermal stability, among which ANPTz had the best thermal stability (Td=211.03 ℃). In addition, HCN, CO2, H2O and NO2 were released during thermal decomposition process. The self-accelerating decomposition temperature (TSADT) and thermal explosion critical temperature (Tb) were calculated to evaluate thermal safety, and the relative order was as follows: FANG (TSADT=198.68 ℃, Tb=209.97 ℃)> ANPTz (TSADT=194.12 ℃, Tb=208.63 ℃)> BANTz (TSADT=182.52 ℃, Tb=207.54 ℃)> AANG (TSADT=180.04 ℃, Tb=188.35 ℃)> CABNG (TSADT=176.80 ℃, Tb=187.32 ℃)> MABNG (TSADT=173.61 ℃, Tb=184.29 ℃). The results indicated that FANG had the acceptable sensitivity (IS=7.84 J), good detonation performance (D=8320 m·s-1, P=30.02 GPa), and the significant catalytic effect (the decomposition temperature of RDX decreased by 8.31 ℃). Six nitroguanidyl-functionalized nitrogen-rich compounds were synthesized and characterized by EA, FT-IR, 1H NMR and 13C NMR. In addition, the crystal structures of ANPTz, CABNG and FANG were further determined by X-ray single crystal diffractometer. The thermal decomposition behaviours were studied by DSC-TG-FTIR-MS coupling technique and the results showed that all the compounds had good thermal stability, among which ANPTz had the best thermal stability (Td=211.03 ℃). In addition, HCN, CO2, H2O and NO2 were released during thermal decomposition process. The self-accelerating decomposition temperature (TSADT) and thermal explosion critical temperature (Tb) were calculated to evaluate thermal safety, and the relative order was as follows: FANG (TSADT=198.68 ℃, Tb=209.97 ℃)> ANPTz (TSADT=194.12 ℃, Tb=208.63 ℃)> BANTz (TSADT=182.52 ℃, Tb=207.54 ℃)> AANG (TSADT=180.04 ℃, Tb=188.35 ℃)> CABNG (TSADT=176.80 ℃, Tb=187.32 ℃)> MABNG (TSADT=173.61 ℃, Tb=184.29 ℃). The results indicated that FANG had the acceptable sensitivity (IS=7.84 J), good detonation performance (D=8320 m·s-1, P=30.02 GPa), and the significant catalytic effect (the decomposition temperature of RDX decreased by 8.31 ℃).

The accompanying file include information regarding the set up of WRF simulations of power production and wake extents from offshore wind lease areas along the U.S. east coast, and also data presented in figures in the "Wind power production from the U.S. east coast offshore lease areas" paper and the associated MATLAB data processing code. The US Department of Energy Office of Science (DE-SC0016605), the US Department of Energy Office of Energy Efficiency and Renewable Energy and New York State Energy Research and Development Authority via the National Offshore Wind Research and Development consortium (147505) funded this research. This research was enabled by computational resources supported by the U.S. National Science Foundation via the Extreme Science and Engineering Discovery Environment (XSEDE) (award TG-ATM170024) and ACI-1541215, and those of the National Energy Research Scientific Computing Center, a DOE Office of Science User Facility supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.

1.Perennial bioenergy systems, such as switchgrass and restored prairies, are alternatives to commonly used annual monocultures such as maize. Perennial systems require lower chemical input, provide greater ecosystem services such as carbon storage, greenhouse gas mitigation, and support greater biodiversity of beneficial insects. However, biomass harvest will be necessary in managing these perennial systems for bioenergy production, and it is unclear how repeated harvesting might affect ecosystem services. 2.In this study, we examined how repeated production-scale harvesting of diverse perennial grasslands influences vegetation structure, natural enemy communities (arthropod predators and parasitoids), and natural biocontrol services in two states (Wisconsin and Michigan, USA) over multiple years. 3.We found that repeated biomass harvest reduced litter biomass and increased bare ground cover. Some natural enemy groups, such as ground-dwelling arthropods, decreased in abundance with harvest whereas others, such as foliar-dwelling arthropods increased in abundance. The disparity in responses is likely due to how different taxonomic groups utilize vegetation and differences in dispersal abilities. 4.At the community level, biomass harvest altered community composition, increased total arthropod abundance, and decreased evenness but did not influence species richness, diversity, or biocontrol services. Harvest effects varied with time, diminishing in strength both within the season (for total abundance and evenness), across seasons (for evenness), or were consistent throughout the duration of the study (for community composition). Greater functional redundancy and compensatory responses of the different taxonomic groups may have buffered against the potentially negative effects of harvest on biocontrol services. 5.Synthesis and applications. Our results show that in the short-term, repeated harvesting of perennial grasslands (when insect activity is low) consistently altered vegetation structure but had mixed effects on natural enemy communities and no discernable effects on biocontrol services. However, the long-term effects of repeated harvesting on vegetation structure, natural enemies, and other arthropod-derived ecosystem services such as pollination and decomposition remain largely unknown. Kim et al. 2017 Harvest effects on natural enemy communities and biocontrolData summary tables and site information used in Kim et al. 2017. Harvesting biofuel grasslands has mixed effects on natural enemy communities and no effects on biocontrol services. Journal of Applied Ecology.Kim et al-Harvest effects on natural enemy communities and biocontrol JAE.xlsx

This project was part of the Characterizing Behaviors and Capabilities for Emerging Connected and Automated Vehicle Technologies, Sensors, and Connectivity project. The National Renewable Energy Laboratory partnered with Cummins Inc. to collect data from Class 8 tractor trailer combinations in platoon (cooperative adaptive cruise control) operations on public roads in southern Indiana. Data collected include J1939 CAN bus, radar, intervehicle position, and video data. The video data could not be shared in the raw form, so they were processed to extract information on the other vehicles on the road, their relative positions, and intrusion events. This information was then columnized for modeling use and further enhanced by appending road information including road type, speed limit, altitude, and grade. The test route included free-flowing traffic, highway interchanges, and construction zones, as well as low-, medium-, and high-grade sections. Individual test conditions varied by day, with advanced driver-assistance system (ADAS) features engaged or disengaged and different combined vehicle masses tested in addition to uncontrolled variables such as weather and traffic interactions.