• Energy Research
• 7. Clean energy close
• 12. Responsible consumption close
• US close
• GB close
• IT close
• CA close

The paper presents a preliminary technical-economic comparison between a 3 kV DC railway and the use of trains with on-board storage systems. Numerical simulations have been carried out on a real railway line, which presents an electrified section at 3 kV DC and a non-electrified section, currently covered by diesel-powered trains. Different types of ESS have been analyzed, implementing the models in Matlab/Simulink environment. A preparatory economic investigation has been carried out.

Abstract This paper investigates the performance of a variable ratio gearbox (VRG) used in a small fixed-speed wind turbine with active blades. The major components of the VRG-enabled drivetrain are an automatic-manual gearbox and squirrel cage induction generator that connects directly to the grid. The simplicity of this system may be appealing for applications when cost and reliability are of concern. It is an alternative to variable speed systems, which necessitate a modified generator and power conditioning equipment. During partial load operation the VRG provides a discrete set of rotor speeds. This allows the controller to track the wind speed and to achieve a greater efficiency. This study suggests three VRG ratios are sufficient to improve performance when used with active blades. A case study is presented where the performance is simulated using three different wind data sets. The study suggests that the VRG can improve production between 7 and 8.5% in low wind areas. The design procedure also illustrates a technique for finding the lowest and highest gear ratios needed for VRG design. These ratios allow the system to achieve the lowest cut-in and rated speeds. The approach also has useful implications for the design of a continuously variable transmission.

With the integration of a high penetration of wind power into distribution system, the ability to cope with the voltage fluctuation issue arising from the intensified uncertainty should be improved. Energy storage system (ESS) with effective control strategies keeps a key role in smoothing the voltage fluctuation caused by the uncertainty of wind turbine generators (WTGs). Considering the constraints of state of charge (SOC), charge-discharge efficiency and continuous operation of ESS, this paper proposes a novel approach to determine the minimum capacity of ESS to satisfy the voltage fluctuation limit based on unbalanced three-phase interval power flow. An unbalanced forward-backward sweep interval power flow considering the constraints of ESS and the voltage fluctuation limit is proposed. The interval model of uncertain WTG output is established on basis of wind speed fluctuation curve. The interval model of the practical ESS output is obtained on basis of the present SOC, nominal capacity and comprehensive efficiency. The output voltages of power flow can directly demonstrate the voltage fluctuation rate due to their interval forms. Therefore, a feedback mechanism is established between the output voltage fluctuation rate and the input ESS practical power, which is used to determine the minimum capacity of ESS to satisfy the fluctuation limit. A modified IEEE 33-bus system with high penetration of WTGs is implemented to test the proposed method. Results demonstrate the validity and effectiveness of the proposed approach.

Abstract A CFD modelling study has been undertaken to examine the co-firing of pulverised coal and biomass with particular regard to the burnout of the larger diameter biomass particles. Computations were based on a research combustion facility that replicates an industrial coal-fired power station. Three percent, by mass, of pinewood was blended with a bituminous UK coal, and the effects of the wood particle size and shape on the burnout of the combined wood and coal char were investigated. The effect of varying the devolatilisation and char combustion rate constants for the biomass component in the blend was also investigated. It was concluded that the combustion of small (200 μm) wood particles was rapid but the rate of combustion of larger particles was dependent on their composition, size, and shape.

The Sulphurdale Geothermal Field is located in Beaver County Utah, within the boundaries of the Cove Fort--Sulphurdale Known Geothermal Resource Area (KGRA). During the past year, three wells drilled in Section 7, T-26-S, R-6-W, have produced dry steam from a fractured volcanic formation located at a depth of about 1100 feet. Two of these three wells are currently prepared to supply steam to a power plant, and one well has been plugged and abandoned. ThermaSource, Inc. was retained by Mother Earth Industries, the operator of the field, to conduct well tests and render an opinion as to the nature of the geothermal reserves and assess the commercial potential of these reserves. Because of the limited area that has been explored to date, there can be no assurance that the reserves estimate will prove accurate. Project economics are based on parameters believed to be accurate, but there is no assurance that such cash flow projections will be realized.

The Severn Estuary has the world's second largest tide range and a barrage across the estuary, located just seawards of Cardiff in Wales and Weston in the South West England, has been proposed for over half a century, with the objective of extracting large amounts of tidal energy. A Severn Barrage, as previously proposed by the Severn Tidal Power Group (STPG), would be the largest renewable energy project for tidal power generation in the world, if built as proposed, and would generate approximately 5% of the UK's electricity needs. However, concerns have been raised over the environmental impacts of such a barrage, including potential increase in flood risk, loss of intertidal habitats etc. In addressing the challenges of maximizing the energy output and minimizing the environmental impacts of such a barrage, this research study has focused on using a Continental Shelf model, based on the modified Environmental Fluid Dynamics Code (EFDC) with a barrage operation module (EFDC_B), to investigate both the far and near field hydrodynamic impacts of a barrage for different operating scenarios. Three scenarios have been considered to simulate the Severn Barrage, operating via two-way generation and using different combinations of turbines and sluices. The first scenario consisted of 216 turbines and 166 sluices installed along the barrage; the second consisted of 382 turbines with no sluices; and the third consisted of 764 turbines and no sluices. The specification of the sluice gates and turbines are the same for all scenarios. The model results indicate that the third scenario has the best mitigating effects for the far-field and near-field flood risks caused by a barrage and produces the most similar results of minimum water depth and maximum velocity distributions to those obtained from simulating the natural conditions of the estuary, i.e. the current conditions. The results also show that the flow patterns around the barrage are closest to those for the existing natural conditions with minimal slight changes in the estuary. Thus, the results clearly indicate that the environmental impacts of a Severn Barrage can be minimized if the barrage is operated for two-way generation and under the third scenario. Although it appears that the energy output for the third scenario is less than that obtained for the other two scenarios, if very low head (VLH) turbines are used, then the third scenario could generate more energy as more turbines could be cited along the barrage structure. Therefore, the study shows that a Severn Barrage, operating in two-way generation and with 764 turbines (ideally VLH turbines), would be the best option to meet the needs of maximizing the energy output, but having a minimal impact on environmental changes in the estuary and far-field.

Biomass plays an important role in the world primary energy supplies, currently providing ∼14% of the world's primary energy needs and being the fourth largest contributor following coal, oil and natural gas. Over the past decade, domestic biomass heating has received more governmental and public supports than ever before in many developed countries, such as the UK. Although biomass combustion releases some combustion pollutants, biomass is renewable and produces little net CO 2 emissions to the atmosphere. Owing to the low sulphur and low nitrogen contents of many biomass materials, substituting biomass for fossil fuels, particularly coal, can reduce SO x and NO x emissions. This study investigated flue gas emissions, particularly carbon monoxide and nitrogen oxides, of a domestic biomass boiler under various operating conditions. The biomass boiler used in this study satisfies the current EU regulation (EN 303-05) on emissions of domestic biomass boilers. Emissions of the boiler had been measured not only under normal combustion conditions, but also under 'idle' combustion conditions when the boiler was not in but was ready for full operation. The experimental results are analysed and presented in this paper. Copyright The Author 2010. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oxfordjournals.org, Oxford University Press.

Abstract The adoption rate and stringency of building energy standards in the U.S. have been increasing since the mid-1990s as a result of the Energy Policy Act mandate of 1992 (EPAct). Current evidence on the energy savings that accrue from commercial building energy standards is based on engineering simulations, which do not account for realized behaviour once a standard is actually adopted. This paper uses quasi-experimental variation in commercial building energy standard adoptions to estimate their effect on realized electricity consumption and cost-effectiveness. In states induced by EPAct to adopt an energy standard where all new nonresidential construction was erected under a commercial standard, electricity consumption per service worker is lower by about 12%, and total commercial electricity consumption is lower by 10%. Including early adopters and never-adopters to the analysis leads to a downward bias in the treatment effect. The realized electricity savings in the EPAct states represent three quarters of predicted simulated savings, and electricity saved in 2010 came at a cost of approximately 7.7 cents per kWh.

Dynamic loading of transformers is the term used when the loading capacity is calculated using an appropriate thermal model while taking into account the load magnitude, load shape, thermal limits and external cooling conditions. For transformer dynamic loading, the aim is to estimate the transformer's maximum dynamic loading capacity without violating the hottest-spot temperature (HST) and top-oil temperature (TOT) thermal limits. These two temperatures are proxy measures of insulation temperature, which can be used to estimate the loss of service life. The accuracy of the TOT and HST predictions is dependent on many things, central to which is the accuracy of the thermal model. This paper introduces metrics that can be used to differentiate between reliable and unreliable transformer thermal models. The two models discussed in this paper for HST and TOT are the non-linear IEEE model and the model developed by the authors using linear regression methods.