• Energy Research
• Closed Access close
• Embargo close
• engineering and technology close
• US close
• GB close
• IT close

Abstract The analysis and optimization of flat plate fins of constant thickness and straight base has been conducted for different fin’s shapes. Performance of the fins is quantified through effectiveness and expressed as a function of fin’s shape, width, and area. A linear piecewise function with varying number of evenly spaced sections is used to generate shapes with different number of degrees of freedom, which are classified as constrained- or unconstrained-base depending on the width of the fin at the constant temperature base location. For one- and two-degrees of freedom shapes, a variety of rectangular, triangular, trapezoidal, and rhomboidal geometries are considered and optimized. For more than two-degrees of freedom, more complex resulting shapes are also considered. By adjusting the value of the corresponding shape parameters, the best possible distributions of available area to maximize heat transfer are obtained, which produce significant improvements favored by smaller width and larger area. Unconstrained-base performs better than constrained-base configurations as they allow the distribution of a larger area close to the high-temperature base. Optimal shape of unconstrained-base fins is in general convergent with non-zero wide tip, while, for constrained-base fins, it is divergent in the first linear section from the base and convergent in the remaining ones. For increasing number of degrees of freedom the optimized shapes tend to resemble natural structures while effectiveness increases asymptotically to a limit for constant width and area. Besides determining the optimal configurations, consideration has been made about the optimal regions where a variety of shapes produce virtually the same effectiveness of the absolute maximum, which can be used to design fins with almost maximum performance but having simpler shapes or being functional under possible space restrictions. The dimensionless model and the systematic analysis proposed in this work are not only appropriate to study a wide range of flat plate fins but also can be implemented to analyze and perform optimization over other type of fins and fins configurations.

Abstract Dimethyl ether appears to be a better choice among various diesel alternatives due to its high cetane number and sootless combustion. However, the physical and chemical properties of dimethyl ether are very different from those of diesel. The physical properties influence spray formation and atomization characteristics, while chemical properties determine combustion and emission formation characteristics. Thus, fuel's physical and chemical properties significantly determine engine performance and emissions. In the present work, spray combustion and emission formation characteristics of n-heptane, dimethyl ether, and their blends (10, 25, and 50% dimethyl ether in n-heptane) were numerically studied in a constant volume chamber. Results show that the n-heptane spray combustion has the highest heat release rate with an intense premix combustion phase, whereas dimethyl ether spray combustion has the lowest heat release rate and shortest premix combustion phase. The magnitude of the premixed phase and heat release rate decreases with the increase in dimethyl ether mass fraction in the blends. Soot, carbon monoxide (CO), unburned hydrocarbon (UHC), and nitric oxide (NO) emissions decreased with the increase in the dimethyl ether mass fraction in the blends and were lowest for the dimethyl ether.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

Abstract Pollution control strategies currently in use by electric power systems are reviewed and a new minimum emission dispatch (MED) method is developed. This new method minimizes overall emission levels at an increased cost in large-scale power systems while simultaneously accommodating local pollution level requirements, as well as economic constraints.

Given the considerable scale of distribution networks in urban and rural areas, as well as the lack of management records, adjustments of switches during the distribution system operation are poorly documented. Such deficiency results in the inaccuracy of models stored in the distribution network automation system, and thus misleads the state estimation. With the emergence of information and communication technology, a large number of the feeder and residential smart meter data are accumulated. Such data can help recognize the operation modes of distribution networks by analyzing the relationships between the on/off states of switches and the voltage correlations among buses. However, the limited quantity and quality of the sampling data restrict the implementation of data-driven recognition. In this paper, a physical-probabilistic-network (PPN) model applied for inferring overall operation mode of distribution networks is proposed. Based on which, a belief propagation-based algorithm is proposed for the inference even under situations when there are only partial bus voltages data available. Meanwhile, the required variable for inference can be reduced from the active trail analysis. Experiment results are used to compare its performance with classic methods and to prove its effectiveness and advantages.

Abstract Wellbore pressure gradient in gas wells is significant in designing deliquification technologies and optimizing production. At present, no model has yet to be established specifically for gas wells at a wide gas flowrate range. When calculating pressure gradient in a specific gas field, engineers must evaluate these widely used models and get the best performance model at a certain range. To establish a more comprehensive model in horizontal gas wells, an experimental study was conducted to investigate the flow behavior of liquid-gas two-phase flow at different gas and liquid velocities and inclined angles in a 50 mm visual pipe. The evaluation of these widely used models against the experimental data shows that no model can predict liquid holdup at different gas velocity ranges, and huge deviations due to several reasons can be observed. After conducting a comprehensive analysis, a new liquid holdup correlation was proposed based on the Mukherjee–Brill model by correlating from the experimental results, which have parametric ranges closer to the production of gas wells. This new model adopts a new dimensionless gas velocity number to characterize flow similarities and better scale up pressure from the experiment to the gas wells. By validating against experimental data and field data, the results indicate that the new two-phase flow model has stable performance and can accurately predict pressure gradients at different ranges of pressure and gas/liquid velocities.

According to the renewable energy directive 2009/28/EC, the European Union Member States should increase by 2020 the use of renewable energy to 20% of gross final energy consumption and to reach a mandatory share of 10% renewable energy in the transport sector. This study aims to quantify the impact of 2020 bioenergy targets on the land use in the EU, based on the projections of the National Renewable Action Plans in four scenarios: Scenario 1. Bioenergy targets according to NREAPs; Scenario 2. Bioenergy targets according to NREAPs, no second generation biofuels; Scenario 3. Bioenergy targets according to NREAPs, reduced import of biofuels and bioliquids; Scenario 4. Bioenergy targets according to NREAPs, high imports of biofuels and bioliquids. This study also considers the credit for co-products generated from biofuel production. The analysis reveals that the land used in the EU for bioenergy would range between 13.5 Mha and 25.2 Mha in 2020. This represent between 12.2% and 22.5% of the total arable land used and 7.3% and 13.5% of the Utilised Agricultural Area (UAA). In the NREAPS scenario, about 17.4 Mha would be used for bioenergy production, representing 15.7% of arable land and 9.4% of UAA. The increased demand from biofuels would lead to an increased generation of co-products, replacing conventional fodder for animal feed. Considering the co-products, the land used for bioenergy would range between 8.8 Mha and 15.0 Mha in 2020 in the various scenarios. This represent between 7.9% and 13.3% of the total arable land used in the EU and 4.7% and 8.0% of the UAA. In the NREAPS scenario, when co-products are considered, about 10.3 Mha would be used for biofuels, bioliquids and bioenergy production, representing 9.3% of arable land and 5.6% of agricultural land. This study further provides detailed data on the impact on land use in each Member State.

AbstractAn arc‐furnace model consisting of non‐linear, time‐varying resistance, realized by the Alternative Transients Program (ATP), is presented in this paper. It is shown that the model is appropriate for flicker investigation in electrical networks supplying arc furnaces, constituting a valid alternative to the linear arc modelling realized by amplitude modulation of voltage generators. Block diagram of the procedure for ATP modelling of the nonlinear, time‐varying arc resistance, dynamic voltage‐current characteristic of the furnace electric arc, voltage and current arc waveforms and characteristic curves of an arc furnace, obtained by ATP simulation, are presented, referring to circuit parameters taken from an actual plant and to a sinusoidal law for arc‐length time variation. Aflickermeter ATP simulation is realized to derive equivalent voltage‐variation values in agreement with the actual flicker measurements.