• Energy Research
• Closed Access close
• Open Source close
• 7. Clean energy close
• US close

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

Abstract This study sought to quantify and characterize cassava waste as fuel. The wastes from three cultivars were collected to study and were divided into three distinct parts of the cassava plant: seed stem, thick stalks, and thin stalks. Physical and chemical analyzes were carried out to determine the elemental composition of the waste: volatile matter; fixed carbon; ash; moisture; lignin; cellulose; hemicellulose; ash composition and higher heating value were determined. We conducted a thermogravimetric analysis in oxidizing and inert atmospheres to study the behavior of the waste as fuel. The root productivity obtained ranged from 7.7 to 13.0 t ha−1 yr−1 on a dry basis (db), and the ratio between waste and roots varied from 0.36 to 0.91. The physical and chemical properties of cassava waste are analogous to those of woody biomass regarding the elemental composition, the higher heating value, and thermogravimetric analysis. Ash content varied from 2.5% to 3.5%, reaching around 6.0% in samples unwashed. Approximately 60% of the ashes are alkali oxides, especially P2O5, K2O, and CaO, which have low melting points. The alkali index calculated suggests that there is a strong tendency that the combustion process leads to ash fouling and the formation of ash deposits.

A mathematical model of the LiAl/LiCl, KCl/FeS cell has been used to study the behavior of the system during relaxation and charging. The effects of state of charge, cell temperature, and current density are presented, and the influence of a period of relaxation on the subsequent charging operation is investigated. In addition, factors that can have a significant impact on the charging characteristics are identified.

Purpose This study aims to consider environmental sustainability, a global challenge under the preview of sustainable development goals, highlighting the significance of knowledge economy in attaining sustainable aggregate demand behavior globally. For this purpose, 155 countries that have data available from 1995 to 2021 were selected. The purpose of selecting these countries is to test the global responsibility of the knowledge economy to attain environmental sustainability. Design/methodology/approach Results are estimated with the help of panel quantile regression. The empirical existence of aggregate demand-based environmental Kuznets curve (EKC) was tested using non-linear tests. Moreover, principal component analysis has been incorporated to construct the knowledge economy index. Findings U-shaped aggregate demand-based EKC at global level is validated. However, environmental deterioration increases with an additional escalation after US$497.945m in aggregate demand. As a determinant, the knowledge economy is reducing CO2 emissions. The knowledge economy has played a significant role in global responsibility, shifting the EKC downward and extending the CO2 reduction phase for every selected country. Further, urbanization, energy intensity, financial development and trade openness significantly deteriorate the environmental quality. Originality/value This study contains the empirical existence of aggregate demand-based EKC. The role of the knowledge economy is examined through an index which is calculated by using four pillars of the knowledge economy (technology, innovations, education and institutions). This study is based on a combined panel of all the countries for which the data was available.

The division of return stroke current among the arresters and groundings of two unenergized test distribution lines, one horizontally configured and the other vertically configured, was studied at the International Center for Lightning Research and Testing in Florida. The division of return stroke currents for the vertically configured line was initially similar to the division on the horizontally configured line: at the time the return stroke current reached peak value (after one microsecond, or so) the two closest arresters/grounds on both lines passed about 90% of the total current. However, the time during which the return stroke current flowed primarily through the closest arresters to the neutral conductor was significantly shorter on the vertically configured line. On that line, the arrester current was about equally divided among all four arresters after several tens of microseconds. The arrester current division as a function of time measured on the vertical line was successfully modeled using the published VI-characteristic, while the division on the horizontal line after some tens of microseconds was only successfully modeled if the residual voltage of the two arresters closest to the current injection point was reduced by 20%. Based on the triggered lightning current division observed on our line, the minimum energy absorbed in each of the two arresters closest to the strike point during a typical natural first stroke is estimated to be 40 kJ.

Abstract Molten salt reactors (MSRs) are a class of next-generation nuclear reactors that have received recent industrial and research interest. A generalized species transport solver was implemented in the Virtual Environment for Reactor Applications (VERA) computing suite to extend this tool to analyze liquid-fueled MSRs. This core simulator has been extended to model the transport of fission product gases into a collection of circulating gas bubbles with the purpose of removing the gases. This paper presents the governing species transport equation, along with various nuclear source terms. Development of the source term for phase migration is discussed, along with a simplified interfacial area tracking method. Finally, a case study on a simplified MSR loop is presented in which modeling parameters were varied to assess their impact on gas removal. The steady state results show that parameters such as bubble diameter, gas injection rate and mass transfer coefficient have a low to moderate effect on the fraction of xenon in the core region. Removal efficiency has the greatest effect on the fraction in the core region. After the pump bowl, bubble diameter has a minor effect on the fraction of xenon in the gas void. These results point out that increasing parameters such as mass transfer coefficient, gas injection rate, and removal efficiency drives the xenon into the circulating gas void, while decreasing bubble diameter also drives xenon into the gas void by increasing interfacial area.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Paper mill sludge (PMS) is a residual biomass that is generated at paper mills in large quantities. Currently, PMS is commonly disposed in landfills, which causes environmental issues through chemical leaching and greenhouse gas production. In this research, we are exploring the potential of fast pyrolysis process for converting PMS into useful bio-oil and biochar products. We demonstrate that by subjecting PMS to a combination of acid hydrolysis and torrefaction pre-treatment processes it is possible to alter the physicochemical properties and composition of the feedstock material. Fast pyrolysis of pretreated PMS produced bio-oil with significantly higher selectivity to levoglucosenone and significantly reduced the amount of ketone, aldehyde, and organic acid components. Pretreatment of PMS with combined 4% mass fraction phosphoric acid hydrolysis and 220 °C torrefaction processed prior to fast pyrolysis resulted in a 17 times increase of relative selectivity towards levoglucosenone in bio-oil product along with a reduction of acids, ketones, and aldehydes combined from 21 % to 11 %. Biochar, produced in higher yield, has characteristics that potentially make the solid byproduct ideal for soil amendment agent or sorbent material. This work reveals a promising process system to convert PMS waste into useful bio-based products. More in-depth research is required to gather more data information for assessing the economic and sustainability aspects of the process.

Abstract This paper presents a novel multi-time-stage input–output-based modeling framework for simulating the dynamics of bioenergy supply chains. One of the key assumptions used in the model is that the production level at the next time-stage of each segment of the energy supply chain adjusts to the output surplus or deficit relative to targets at the current time period. Furthermore, unlike conventional input–output models, the technology matrix in this approach need not be square, and thus can include coefficients denoting flows of environmental goods, such as natural resources or pollutants. Introducing a feedback control term enables the system to regulate the dynamics, thus extending the model further. This is an important feature since the uncontrolled dynamic model exhibits oscillatory or unstable behavior under some conditions; in principle, the control term allows such undesirable characteristics to be suppressed. Numerical simulations of a simple, two-sector case study are given to illustrate dynamic behavior under different scenarios. Although the case study uses only a hypothetical system, preliminary comparisons are made between the simulation results and some broad trends seen in real bioenergy systems. Finally, some of the main policy implications of the model are discussed based on the general dynamic characteristics seen in the case study. In particular, insights from control theory can be used to develop policy interventions to impart desirable dynamic characteristics to nascent or emerging biofuel supply chains. These interventions can be used to guide the growth of bioenergy supplies along final demand trajectories with minimal fluctuation and no instability.