• Energy Research
• Closed Access close
• Open Source close
• natural sciences close
• 12. Responsible consumption close

Plastic film mulching (FM) became a general practice to enhance crop productivity and its net primary production (NPP), but it can increase greenhouse gas (GHG) emissions. The proper addition of organic amendments might effectively decrease the impact of FM on global warming. To evaluate the feasibility of biomass addition on decreasing this negative influence, cover crop biomass as a green manure was incorporated with different recycling levels (0-100% of aboveground biomass) under FM and no-mulching. The net global warming potential (GWP) which integrated with soil C stock change and GHG (N2O and CH4) fluxes with CO2-equivalent was evaluated during maize cultivation. Under the same biomass incorporation, FM significantly enhanced the grain productivity and NPP of maize by 22-61 and 18-58% over no-mulching, respectively. In contrast, FM also highly increased the respired C loss, which was 11-95% higher than NPP increase, over no-mulching. Irrespective with biomass recycling ratio and mulching system, negative NECB which indicates the decrease of soil C stock was observed, mainly due to big harvest removal. FM decreased more soil C stock by 57-158% over no-mulching, but its C stock was clearly increased with increasing biomass addition. FM significantly increased total N2O and CH4 fluxes by 4-61 and 140-600% over no-mulching, respectively. Soil C stock changes mainly decided net GWP scale, but N2O and CH4 fluxes negligibly influenced. As a result, FM highly increased net GWP over no-mulching, while this net GWP was clearly decreased with increasing biomass application. However, cover cropping, and its biomass recycling was not enough to compensate the negative impact of FM on global warming. Therefore, more biomass incorporation might be essential to compensate this negative effect of FM.

The current status and challenges associated with the production and utilization of cellulosic ethanol in Korea are reviewed in this paper. Cellulosic ethanol has emerged as a promising option for mitigating Korea's CO(2) emissions and enhancing its energy security. Korea's limited biomass resources is the most critical barrier to achieving its implementation targets for cellulosic ethanol. Efforts to identify new suitable biomass resources for cellulosic ethanol production are ongoing and intensive. Aquatic biomasses including macroalgae and plantation wastes collected in the Southeast Asia region have been found to have great potential as feedstocks for the production of cellulosic ethanol. R&D explorations into the development of technologies that can convert biomass materials to ethanol more efficiently also are underway. It is expected that cellulosic ethanol will be in supply from 2020 and that, by 2030, its use will have effectively reduced Korea's total gasoline consumption by 10%.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

Anode with good electrocatalytic capabilities is more specifically required to reduce the ohimic losses during microbial fuel cell (MFC) operation. Highly conductive polymers viz., Polyaniline (PANi) and Polyaniline/Carbon nanotube (PANi/CNT) composite were prepared by in situ oxidative chemical polymerization method. Anodes were fabricated independently by coating PANi and CNT/PANi composites on the surface of SSM. The fabricated electrodes were evaluated as anode against stainless steel mess (SSM) as cathode during MFC operation. Maximum bioelectricity generation was observed in SSM-PANi/CNT-anode with power density of 48 mW/m2 and COD removal efficiency of 80% compared with SSM-PANi-anode (38 mW/m2; 65%) and SSM-anode (28 mW/m2; 58%). Bioelectrochemical characterization of the electrode materials using cyclic voltammetry and electrochemical impedance spectroscopy showed high electrocatalytic activity of PANi/CNT composite electrode. The study concluded the efficiency of PANi/CNT composite electrodes as bioanode in operation of MFCs towards achieving increased bioelectricity production along with wastewater treatment.

AbstractSlaughterhouses generate highly polluted effluents, and if not treated before discharge can cause major adverse environmental and public health impacts. Treatment of this waste by anaerobic digestion can reduce those impacts while producing a potentially valuable source of energy. The purpose of this study was to investigate this process efficiency under pilot operating conditions for a more accurate scaling up. Blood waste from a slaughterhouse was treated in a pilot‐scale digester of 30 dm3 total volume under mesophilic temperature conditions. Operating parameters such as pH, alkalinity, organic loading, volatile fatty acids, biogas composition, total and volatile solids were monitored in order to study the behavior of the fermentation process. The results show that no significant inhibition were caused by the accumulation of volatile fatty acids, due to the high buffering capacity of treated sludge. An efficient reduction of organic matter was obtained with a COD decrease of about 67% within 40 days of fermentation. The biogas produced was of a good quality with high CH4 yields (above 70%) and low CO2 yields, corresponding to a biomethane potential of 225.9 dm3 CH4/kg TVS. Logistic model described accurately the methane production kinetic and enables an easy process scaling up for industrial applications.

Wastewater containing ammonia nitrogen compounds is considered as a harmful material to environment due to eutrophication and toxicity effects; hence, finding practical methods for treating this type of wastewater seems necessary. In this study, performance of two sequencing batch reactors have been assessed for simultaneous nitrification and denitrification in treating synthesized wastewater containing ammonium nitrogen, using leachate obtained from cow dung as the biomass. The leachate obtained from cow dung as the source of bio‐sludge added to the reactors. Experiments were designed according to central composition design and response surface methodology with four operating variables including pH (6, 7.5, 9), cycle time (CT) (4, 12, 20 h), ratio (5, 10, 15) and carbon source (Sodium acetate: , Glucose: ). According to statistical analysis, experimental responses were in acceptable agreement with model predictions. CT was the most important operating variable in chemical oxygen demand (COD) and removal. The maximum percentage of ammonium nitrogen removal was attained at pH 7.5 and CT 21.5 h. The optimum conditions were composed of pH 7.67, CT 19.15 h, 10.95 and sodium acetate as carbon source, while COD, and total nitrogen removals were 94.96%, 94.93% and 93.60%, respectively. © 2017 American Institute of Chemical Engineers Environ Prog, 37: 1638–1646, 2018

Highly efficient nanocatalysts which can selectively decompose hydrous hydrazine for hydrogen production are introduced.

One of the most popular off‐site wastewater treatment plants used in the tropics is the waste stabilization pond (WSP). Although it has several advantages, its use in urban areas is limited because of its large land area requirement. Hence, this research is aimed at investigating if a solar‐enhanced WSP (SEWSP) can increase treatment efficiency and consequently reduce the land area requirement. The SEWSPs of varying sizes, made of a metallic tank with inlet and outlet valves and a solar reflector, were constructed to increase the incident sunlight intensity. Wastewater samples collected from the inlet and outlet of the SEWSPs were examined for physio‐chemical and biological characteristics for a period of 2 months. The parameters examined were total suspended solids, dissolved oxygen, 5‐day biochemical oxygen demand (BOD 5), chemical oxygen demand (COD), coliform, and Escherichia coli. The efficiencies of the SEWSPs, with respect to these parameters, fluctuated with temperature variation, with the shallowest SEWSP giving the highest treatment efficiency. The research revealed that the cost of treating wastewater using SEWSPs was approximately 2 times lower than the conventional WSP for the same treatment efficiencies.