• Energy Research
• Open Access close
• Closed Access close
• Embargo close
• engineering and technology close
• 6. Clean water close

In recent years, the rapid development of the rare earth industry has had a serious impact on the environment. Some enterprises have taken measures to improve the production process. In order to explore the sustainability of this industry and these improvements’ environmental benefits, this paper combines emergy analysis and lifecycle assessment to evaluate and compare the production process of rare-earth oxides considering the three aspects of emergy flow, pollutant emissions, and emergy-based indicators. Changes in the emergy of pollutant emissions before and after improvement of the production process are discussed. The results show that the greatest inputs in the mining and beneficiation stage and smelting separation stage are labor force and service and non-renewable resources, respectively. These two production stages are highly dependent on external input and have weak competitiveness. Both stages place great pressure on the environment, so the bastnasite production process would be unsustainable in the long term. After the improvement, the environmental impact of the production process for bastnaesite changed significantly, indicating that the improvement effect of the wastewater treatment facilities and the change of fuel from coal to natural gas is remarkable.

Abstract A great deal of heat is wasted in intensive public shower facilities, such as those in schools, barracks and natatoriums, which open up at specified time. It will contribute a lot to energy saving and environmental protection with significant economic benefits to recycle the exhaust heat. In this paper, we propose two different kinds of heat pumps (an electric heat pump and an absorption heat pump) in the heat recovery systems. In both system, the used shower water is drained through a pipe and collected in a gray water pool. When the wastewater reaches certain volume, the heat pump system will begin working and recycling heat. The wastewater is filtered and piped to the heat exchanger to exchange heat with the tap water whose temperature will increase from 12 °C to 25 °C with the wastewater temperature dropping from 30 °C to 17 °C. Then the wastewater is piped to the heat pump evaporator and the tap water is piped to the condenser for farther heating. According to the different characteristics of the electric heat pump and absorption heat pump, we also introduce the processes and control methods of different heat recovery systems in details in this paper. Based on a practical example, this paper analyzes and compares the economic and environmental benefits of three retrofitting schemes, including “exhaust heat recovery using electric heat pump”, “exhaust heat recovery using electric heat pump + gas boiler” and “exhaust heat recovery using direct-fired heat pump”. Then we find out that the heat recovery system using direct-fired absorption heat pump has lower energy consumption, less pollution, lower operating cost, and shorter payback period. And it has a promising practical application.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

The influence of ethanol on the degradation kinetics of linear alkyl benzene sulfonate (LAS) and organic matter was investigated using batch experiments with different initial LAS concentrations (8.3 mg L-1 to 66.9 mg L-1) and biomass immobilized on sand. Data were fitted with a substrate inhibition model. Concentrations of 2.4 mg LAS L-1 and 18.9 mg LAS L-1 (without and with ethanol) provided the maximum LAS utilization rate by the biomass (Sbm). For LAS degradation, ethanol addition favored a lower decrease in the specific substrate utilization rate (robs), even at the LAS concentration usually reported as inhibitory (> 14.4 mg L-1). For organic matter degradation, robs was higher with ethanol. Higher biomass differentiation was observed at higher LAS concentrations. With ethanol, microbial selection occurred at LAS concentrations near Sbm. At higher LAS concentrations, the dominance and diversity values did not change significantly with ethanol, whereas without ethanol, their behaviors were irregular.

This paper reports the real-time behavior of the leakage current flowing on glass-type insulator strings of a 230-kV substation tower during washing. Monitoring of two insulator strings in the tower is achieved by use of a pair of optical-fiber sensors that detect samples of the leakage current waveforms and transmit those samples to a processing module via an optical link. It is observed that leakage current during washing may reach high peak levels, and the effectiveness of the washing can be inferred by the degree of leakage current after drying of the insulator strings. Direct monitoring of the leakage current can thus be used as an important guideline for proper washing procedures during this type of intervention as well as for determining the effectiveness of the procedure.

Abstract An outlook into the country profile at the existing electricity generation with crude oil production at the present level with accompanying gas flares cause CO 2 emission as well as the industrial, human activities and the grid electricity distribution has been accounted for. The estimation of solar radiation levels as well as its productivity in terms of photovoltaics (PV׳s), concentrated solar powers (CSP) and chimney towers have been paid for others renewable energies; wind, tidal and geothermal productivity. A selection of possible site for installation according to the given geographical hazard and the maximum solar radiation could be collected. An overview for futuristic demands and possible solar energy supply that could be generated has reviewed. Furthermore, the desalination of underground or polluted water to support the solar system as well as the needed plantation to preserve a clean and green environment and low dust climate is presented.

Heavy Metals Content Pb, Cd, Cu, Zn And Ni In Sea Water And Sediment In Membramo Estuary And Its Relationship With Fishery Cultivation. Obervation on heavy metals Pb, Cd, Cu, Zn and Ni content in Jakarta Bay were carried out in August 2003. The results showed that the Pb, Cd, Cu, Zn, and Ni content still in line with threshold value stated by for fisheries. By the all, in sea water Zn content is higher compared to the others, while in sediment Ni is higher. This data showed the result show that on waters of Membramo River Zn and Ni waste than others elements. Keywords: Membramo, heavy metals, fisheries.

In this paper, we propose and investigate an original approach to energy conversion based on polyzwitterionic hydrogels, which exhibit an antipolyelectrolyte effect that enables them to swell in salt water and shrink in water of a different (i.e., desalinated water) salinity. The swelling and shrinking processes run cyclically and can move a piston up or down reversibly, thus transforming the antipolyelectrolyte effect into a mechanical force based on the salinity gradient. This phenomenon makes polyzwitterionic hydrogels suitable for use in a smart, polymeric engine. We apply this approach to investigate energy recovery from a polysulfobetaine-based hydrogel. The cross-linking density, external load, particle size, and repeatability of energy recoverability of hydrogels are examined. The maximum energy recovery from 0.4 g of hydrogel in feed (calculated based on dry form) of 102 mJ/kg was obtained by a hydrogel with a 3% cross-linking density, a 200-300 μm particle size, and 100 g external load. Excellent reproducibility of engine cycles was achieved over 10 cycles. This concept is complementary to the osmotic engine concept based on a polyelectrolyte hydrogel. In addition, polyzwitterionic materials have become a benchmark material for preventing biofouling, and the swelling properties of such materials can be further modulated and tuned.