• Energy Research
• Restricted close
• engineering and technology close
• CNR ExploRA close

Dolomite-based binders are characterised by interesting technical and environmental features. For their synthesis, sources of both CaO and MgO are required. The idea developed in this work is to couple the synthesis of dolomite-based binders, starting from a natural dolomite, through the concept of concentrated solar energy (needed to drive the endothermal dolomite calcination process) in fluidised bed reactors. To this end, a fluidised bed system, where the concentrated solar radiation is mimicked by the use of Xe-lamps (short-arc), has been set up and operated. Natural dolomite (sieved in the 420-590 ?m size range) was calcined at a nominal temperature of 850 °C, and bed temperature profiles during solar-driven calcination were investigated. Then, four binders were prepared by mixing slaked dolomite (obtained from the hydration of solar calcined dolomite) with either blast furnace slag or coal fly ash as supplementary cementitious materials. The binders were hydrated for curing times ranging from 7 to 56 days. X-ray fluorescence, X-ray diffraction and combined differential thermal and thermogravimetric analyses were employed as characterisation techniques both to analyse the chemical composition of starting materials and to investigate the evolution of the hydration in the four systems.

In recent years, the portable technology is receiving a great interest and significant improvement due to the progresses in electronic technology development and energy storage solutions. The decrease in power requirements for working energy systems, due to the increased efficiency and to the reduction in components size, opens the access to new solutions for power supplying. In particular, alternative backup systems for battery charging or replacement could be designed taking advantage of unconventional technologies. It is the case of small photovoltaic portable panels or fuel cells technology: in these solutions different sources are used to produce limited electrical powers required to keep devices on. In this paper, a thermoelectric solution for the power generation has been considered: the generator has been designed and assembled starting from a catalytic combustor. Catalytic combustion allows safe control of the processes, and the choice of a hydrocarbon fuel ensures the power availability and a fast recharge. The size of the system is set to fit a volume close to the one of AA batteries. The electrical power output obtained is close to 1 W with a cold side temperature below 40 °C. The limited values of these physical parameters allow obtaining a portable and safe device. The generator has been fully characterized in different ranges of fuel flow rates and the performances have been thoroughly analysed for processes optimization and efficiency improvement.

The electrodissolution of p-Ge in aqueous NaOH solutions (pH 12-13) has been investigated with steady-state and impedance techniques. In the potential region where the process is under kinetic control, the impedance patterns are characterised by a high frequency capacitive loop, associated with the space charge, largely merged with another due to charge transfer resistance and double layer capacitance, and two low frequency loops changing from inductive to capacitive upon increasing the potential. At larger potential, under mixed control, the same high frequency features are observed, while a convection diffusion impedance dominates the low frequency response. The data relevant to pure kinetic control are interpreted with a simplified kinetic model, based on the classical scheme of Beck and Gerischer [Z. Electrochem., Ber. Bunsenges. Physik. Chem. 63 (1959) 500], neglecting transport effects and assuming only three electrochemical steps: (i) oxidation, involving water molecules, of Ge(0) to dihydroxylated Ge(II) by two holes; (ii) oxidation by one hole of Ge(II)-Ge(III) in a step requiring OH-; (iii) oxidative dissolution of Ge(III) proceeding either by hole capture or electron injection, leaving behind a surface Ge(0) species. Diagrams calculated for the limiting cases of pure depletion layer control reproduce the essential features of the experimental ones.

AbstractThe potential impacts of future climate scenarios on water balance and flow regime are presented and discussed for a temporary river system in southern Italy. Different climate projections for the future (2030–2059) and the recent conditions (1980–2009) were investigated. A hydrological model (Soil and Water Assessment Tool) was used to simulate water balance at the basin scale and streamflow in a number of river sections under various climate change scenarios, based on different combinations of global and regional models (global circulation models and regional climate models). The impact on water balance components was quantified at the basin and subbasin levels as deviation from the baseline (1980–2009), and the flow regime alteration under changing climate was estimated using a number of hydrological indicators. An increase in mean temperature for all months between 0.5–2.4 °C and a reduction in precipitation (by 4–7%) was predicted for the future. As a consequence, a decline of blue water (7–18%) and total water yield (11–28%) was estimated. Although the river type classification remains unvaried, the flow regime distinctly moves towards drier conditions and the divergence from the current status increases in future scenarios, especially for those reaches classified as I‐D (ie, intermittent‐dry) and E (ephemeral). Hydrological indicators showed a decrease in both high flow and low flow magnitudes for various time durations, an extension of the dry season and an exacerbation of extreme low flow conditions. A reduction of snowfall in the mountainous part of the basin and an increase in potential evapotranspiration was also estimated (4–4.4%). Finally, the paper analyses the implications of the climate change for river ecosystems and for River Basin Management Planning. The defined quantitative estimates of water balance alteration could support the identification of priorities that should be addressed in upcoming years to set water‐saving actions.

<div class="section abstract"><div class="htmlview paragraph">The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO₂-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO₂-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.</div><div class="htmlview paragraph">In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm³ single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization.</div><div class="htmlview paragraph">The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.</div></div>

The aim of the paper is to study the influence of the power transformer on signal transmission in the case of a power line communication (PLC) system in a overhead Medium Voltage (MV) power network. A model of the PLC system was carried out by means of the Simulink® software. A distributed parameter MV overhead line, two power transformers, the signal coupling interface of a ST7540 FSK powerline transceiver were included in the model. The performances of the complete PLC communication system are evaluated for different line lengths by means of the attenuation computed as ratio between the received and transmitted voltage signals. © 2011 IEEE.

Technologies for direct injection of fuel in compression ignition engines are in continuous development. One of the most investigated components of this system is the injector; in particular, main attention is given to the nozzle characteristics as hole diameter, number, internal shape, and opening angle. The reduction of nozzle hole diameter seems the simplest way to increase the average fuel velocity and to promote the atomization process. On the other hand, the number of holes must increase to keep the desired mass flow rate. On this basis, a new logic has been applied for the development of the next generation of injectors. The tendency to increase the nozzle number and to reduce the diameter has led to the replacement of the nozzle with a circular plate that moves vertically. The plate motion allows to obtain an annulus area for the delivery of the fuel on 360 degrees; while the plate lift permits to vary the atomization level of the spray. The experimental activities have been performed on a single-cylinder metal engine in order to evaluate the new injector concept functionality in typical engine working conditions. Then a deeper investigation of injector the characteristics has been performed in an optical single-cylinder diesel engine via high speed digital imaging in order to catch information on its operation. The results have shown a good response of the injector fuel delivery control but penalties in terms of emissions and efficiency compared to multihole nozzles. Images of the injection process showed that the fuel assumed an asymmetric shape at the exit of the injector affecting the mixing quality and, then, the combustion efficiency.

This paper investigates the energy distribution and the waste heat energy characteristics of a compression ignition engine for micro-cogeneration applications, at different engine speeds and loads. The experimental activity was carried out on a three-cylinder, 1028 cc, common-rail engine. Tests were performed with diesel fuel and a 20% v/v biodiesel blend (B20). The quantity and the quality of the waste heat energy were studied through energy and exergy analyses, respectively. Combustion characteristics were investigated by means of indicating data. Gaseous emissions were measured and particles were characterized in terms of number and size at exhaust. It was found out that the addition of 20% v/v of RME to diesel fuel does not affect significantly the brake fuel conversion efficiency and the energetic flows. On the other hand, biodiesel blend allows to reduce the combustion noise and the pollutants emissions in most of the operating conditions. A proper phasing of the injection strategy for the biodiesel blend could further reduce the exhaust emissions, mainly at high engine speeds. The results presented in this paper could be useful for the development of diesel engine based micro-cogeneration systems working at different engine speeds and loads.