• Energy Research
• 2016-2025close
• Embargo close
• other engineering and technologies close

[EN] The objective of this article is to compare the behaviour of the most representative domestic hot water systems (DHW) in single-family buildings. The study evaluates the energy consumption, equivalent CO2 emissions and cost for each system over a 15-year life period. This analysis is carried out in four cli- matic zones across Europe to observe the influence of climatic conditions on the results. The four climatic zones are located in the cities of Athens, Madrid, London and Berlin. The analysed systems are: a) natural gas-fired instantaneous water heaters, b) electric storage water heater, c) solar thermal system with gas- fired instantaneous, d) solar thermal system with electric storage water heater, e) air-source heat pump, f) photovoltaic system with electric storage water heater, and g) photovoltaic system with air-source heat pump. This range of technologies covers the most likely solutions to be implemented across domestic buildings in Europe.The heat pump system (HPWH) with PV considering self-consumption shows the lowest environmen- tal impact in all zones, but is not an attractive investment in the coldest zones due to lower natural gas prices. Thermal solar systems have a high purchase and maintenance costs which do not compensate their energy savings. The PV HPWH system has a greater reduction of emissions and a lower cost than HPWH across a 15-year life. The gas boiler system has the lowest cost in a 15-year period in the coldest areas, despite having a greater environmental impact than the heat pump.(c) 2023 Elsevier B.V. All rights reserved.

Abstract This paper examines the effects of foreign trade and foreign direct investment (FDI) on CO 2 emissions in Turkey. We consider linear and nonlinear ARDL models and find significant asymmetric effects of exports, imports and FDI on CO 2 emissions per capita. However, FDI has no statistically significant long-run effects. In the long run, decreases in exports reduce CO 2 emissions per capita but increases in exports have no statistically significant effects. Increases in imports push up CO 2 emissions per capita, while decreases in imports have no long-run effects. On the other hand, CO 2 intensity, which measures CO 2 emissions per unit of energy, is not influenced by exports and imports, nor by FDI. Instead, it is affected positively by financial development and urbanization. Also, we find that an environmental Kuznets curve is present for both CO 2 measures so that increases in real GDP per capita have led to reductions in CO 2 emissions for at least the most recent decade, controlling for other confounding factors. Furthermore, the sectoral shares of CO 2 emissions in total CO 2 emissions change asymmetrically with foreign trade for two of four sectors, with export increases leading to lower CO 2 shares and imports having the opposite effect.

Thermoacoustic technology emerges as a sustainable and low-carbon method for energy conversion, leveraging environmentally friendly working mediums and independence from electricity. This study presents the development of a multimode heat-driven thermoacoustic system designed to utilize medium/low-grade heat sources for room-temperature cooling and heating. We constructed both a simulation model and an experimental prototype for a single-unit direct-coupled thermoacoustic system, exploring its performance in heating-only, cooling-only, and hybrid heating and cooling modes. Internal characteristic analysis including an examination of internal exergy loss and a distribution analysis of key parameters was first conducted in the hybrid cooling and heating mode. The results indicated a positive-focused traveling-wave-dominant acoustic field within the thermoacoustic core unit, enhancing energy conversion efficiency. The output system performance was subsequently tested under different working conditions in the heating-only and cooling-only modes. A maximum output heating power of 2.3 kW and a maximum COPh of 1.41 were observed in the heating-only mode. Meanwhile, a cooling power of 748 W and a COPc of 0.4 were obtained in the typical cooling condition at 7 °C when operating in cooling-only mode. These findings underscore the promising potential of thermoacoustic systems for efficiently utilizing medium/low-grade heat sources for cooling and/or heating applications in the future.

Petroleum-based fuels are used extensively as a result of the rising energy demands. Studies on fuels that will replace these fuels are now ongoing. In this study, performance, emission values of 4 different fuels at 4 different torque values were evaluated, and energy and exergy analyses were done utilizing combinations of gasoline, natural gas, and methanol. The tests employed a Lombardini LGW 523 2-cylinder 4-stroke engine. Four different fuels (gasoline, gasoline plus 50 g of natural gas, M20, and M20 plus 50 g of natural gas) were tested at a constant 3000 rpm with four different torque values (5, 10, 15, 20). In tests, it produced the lowest specific fuel consumption and the best emissions when combined with 50 g of natural gas fuel. The purpose of this study was to show that as torque increased, values for fuel, network, exhaust, absorption water, and energy destruction increased, while rates of lost energy decreased and rates of energy destruction increased.

The lifetime and reliability of power transformers are primarily dependent on the hot-spot temperature in the windings, as temperature is the most important factor determining the insulation degradation rate. Key to removing the heat from the transformer is the radiator which must be carefully designed to keep the temperatures within limits under all operating conditions whilst minimizing the transformer size, weight and cost. This paper compares the analytical method used to predict the radiator performance with computational fluid dynamics (CFD) models in terms of heat dissipation. It is found that the analytical method and CFD models give similar results in the air natural (AN) cooling modes, whereas the analytical method overestimates the heat dissipation in the air forced (AF) cooling modes. Moreover, the thermal conduction effect in the radiator wall is investigated under different operating conditions and for different radiator sizes using the CFD models. The simulation results indicate that the radiator wall contributes to 6%-10% of the total heat dissipation under some circumstances and therefore should not be simply ignored in radiator models.

This paper proposes a novel online and self-learning algorithm to the identification of fuzzy neural networks, which not only learns the structure and parameters online but also learns the threshold parameters by itself and automatically. For structure learning, a self-constructing approach including adding neurons and merging highly similar fuzzy rules is proposed based on the criteria of the system error between actual and model output and the maximum firing strength of neurons. In order to achieve the efficient merging computing, a new calculation method of similarity degree between fuzzy rules is developed. Further and more importantly, the varying width of Gaussian membership functions can be learned by itself according to the underfitting and overfitting criteria. Similarly, different from the existing constant threshold of similarity degree for merging, the varying threshold of similarity degree can be self-learned according to the real-time accuracy of model. The proposed self-learning mechanism significantly improves the model accuracy and greatly enhances the easy usability. Several benchmark examples are implemented to illustrate the effectiveness and feasible of the proposed approach.

Network temperatures in district heating systems are important operational factors for obtaining efficient performance. A low network return temperature allows for the recovery of low-grade heat from assets such as condensing boilers, waste incineration, geothermal sources and industrial waste heat. Fluctuations in heating and cooling demands affect the return temperatures of the building substations and in the network. This variability impacts the economic viability and environmental sustainability of the entire system. This paper presents a nonlinear optimization strategy to maintain sufficient energy flows in the network's primary and secondary circuits to achieve low return temperatures from all substations in the network. The defined optimization strategy incorporates the thermodynamic model of the substation and building heating system as opposed to traditional weather-based supply temperature adjustments. The estimated heat demands and tariffs, CO2 penalties are inputs used by the optimizer to find theoptimal solution. The total operational expenditure for electricity and gas consumption shows an 18% reduction with 8% reduction in emissions and 6% efficiency improvement when compared with the measured weather-based approach. The developed strategy will aid the network operators in the economic dispatch of heat generation while ensuring the user's thermal comfort.

The focus of this study is to analyse and compare the predictive capabilities of univariate and multivariate methods of forecasting the global horizontal irradiance (GHI) for an hour ahead. The forecasting problem is addressed using supervised machine learning methods. In order to simplify the model, a feature selection algorithm is used to identify the highly correlated features. The forecasting is performed by utilizing popular machine learning algorithms viz., random forest (RF), K-nearest neighbors regression (KNN), support vector machine (SVM) and artificial neural networks (ANN). The paper evaluates and contrasts the effectiveness of these models for this application. Additionally, the study examines how the forecasting models' performance varies throughout the year and across seasons.