• Energy Research
• 2021-2025close
• other engineering and technologies close
• 7. Clean energy close
• 1. No poverty close
• 4. Education close

Abstract The ability of the Distributed Generation (DG) to solve problems such as power system deregulation and power demand problems appropriate to its purpose, which is to inject electricity in a distributed manner at a point close to the load, causes the distributed generation to become the latest trend in electricity generation technology. Proper position of distributed generation is necessary in order to achieved maximum benefit from DG, which could be due to an incorrect allocation of DG sources to the power network would not only result in increased power losses, but could also jeopardize the operation of the system. This paper introduces an ACO-algorithm for optimal location of DGs using a real network in one of a rural area of Malaysia. The method is used to determine the effectiveness of DG by comparing the losses of power and the improvement of the voltage profile. As for the confirmation to the ACO method, another method known as brute force method is use to compare the data gain as validation purposes.

High penetration of renewable energy sources into isolated microgrids (µGs) is considered a critical challenge, as µGs’ operation at low inertia results in frequency stability problems. To solve this challenge, virtual inertia control based on an energy storage system is applied to enhance the inertia and damping properties of the µG. On the other hand, utilization of a phase-locked loop (PLL) is indispensable for measuring system frequency; however, its dynamics, such as measurement delay and noise generation, cause extra deterioration of frequency stability. In this paper, to improve µG frequency stability and minimize the impact of PLL dynamics, a new optimal frequency control technique is proposed. A whale optimization algorithm is used to enhance the virtual inertia control loop by optimizing the parameters of the virtual inertia controller with consideration of PLL dynamics and the uncertainties of system inertia. The proposed controller has been validated through comparisons with an optimized virtual inertia PI controller which is tuned utilizing MATLAB internal model control methodology and with H∞-based virtual inertia control. The results show the effectiveness of the proposed controller against different operating conditions and system disturbances and uncertainties.

Abstract This study investigates the non-linear relationship between urbanization paths and CO2 emissions in selected South, South-East, and East Asian countries over the period 1971–2014. Based on the STIRPAT (Stochastic Impacts by Regression on Population, Affluence, and Technology) framework, we applied the advanced and robust methods of dynamic seemingly unrelated regression (DSUR), dynamic OLS (DOLS), and fully modified OLS (FMOLS) to estimate the long-term effects. The empirical findings revealed the inverted U-shaped effects of urbanization and urban agglomeration and the U-shaped impact of the largest city ratio on CO2 emissions. Urbanization and urban agglomerations improve environmental quality in the long-run and support ecological modernization theory. However, excessive concentration in the largest cities have severely affected the environmental quality and violates the notion of compact-city efficiencies. Moreover, energy intensity and economic growth positively affect CO2 emissions, while trade openness negatively influences CO2 emissions. Our robustness analysis at the country-level applies the augmented mean group (AMG) panel ARDL technique, which further supports the non-linear effect of urbanization paths on CO2 emissions except for a few countries. The results of the panel Granger non-causality approach unveil bidirectional causality of energy efficiency, economic growth, urbanization, and largest city ratio with CO2 emissions. In contrast, unidirectional causality runs from urban agglomeration to CO2 emissions. Our findings have important policy implications as we suggest green urban infrastructures, eco-friendly dwellings, smart cities, country-specific trade policies, and renewable energy options to improve the environmental quality.

The Box–Jenkins model is a polynomial model that uses transfer functions to express relationships between input, output, and noise for a given system. In this article, we present a Box–Jenkins linear model for a lithium-ion battery cell for use in electric vehicles. The model parameter identifications are based on automotive drive-cycle measurements. The proposed model prediction performance is evaluated using the goodness-of-fit criteria and the mean squared error between the Box–Jenkins model and the measured battery cell output. A simulation confirmed that the proposed Box–Jenkins model could adequately capture the battery cell dynamics for different automotive drive cycles and reasonably predict the actual battery cell output. The goodness-of-fit value shows that the Box–Jenkins model matches the battery cell data by 86.85% in the identification phase, and 90.83% in the validation phase for the LA-92 driving cycle. This work demonstrates the potential of using a simple and linear model to predict the battery cell behavior based on a complex identification dataset that represents the actual use of the battery cell in an electric vehicle.

The operation of gas generators brings relatively high thermo-mechanical loads on the gas generator structure. The objective of this article is to determine the operating conditions, in terms of mechanical loads at extremely high temperatures in very limited and narrow space, of a multifunctional bulkhead for application on specific kinds of gas generators with back-to-back rotor concept. The paper contains numerical analysis and experimental investigation for determining the loads and behavior of the structure. Numerical analysis indicates that there is significant influence of the Tesla turbine effect on flow parameters. Also, uneven pressure distribution and significant thermal loads are identified. With experimental investigation and subsequent exploitation tests, it was concluded that the presented methodology identifies the operating conditions, truthfully simulates the bulkhead stress state and deformations and that the presented design solution satisfied all demands. Regarding results obtained by these numerical simulations, the innovative design solution for the multifunctional bulkhead was proposed.

The battery power state (SOP) is the basic indicator for the Battery management system (BMS) of the battery energy storage system (BESS) to formulate control strategies. Although there have been many studies on state estimation of lithium-ion batteries (LIBs), aging and temperature variation are seldom considered in peak power prediction during the whole life of the battery. To fill this gap, this paper aims to propose an adaptive peak power prediction method for power lithium-ion batteries considering temperature and aging is proposed. First, the Thevenin equivalent circuit model is used to jointly estimate the state of charge (SOC) and SOP of the lithium-ion power battery, and the variable forgetting factor recursive least squares (VFF-RLS) algorithm and extended Kalman filter (EKF) are utilized to identify the battery parameters online. Then, multiple constraint parameters including current, voltage, and SOC were derived, considering the dependence of the polarization resistance of the battery on the battery current. Finally, the verification experiment was carried out with LiFePO4 battery. The experimental results under FUDS operating conditions show that the maximum SOC estimation error is 1.94%. And the power prediction errors at 20%, 50%, and 70% SOC were 5.0%, 8.1% and 4.5%, respectively. Our further work will focus on the joint estimation of battery state to further improve the accuracy.

Comfort temperature and sleep quality involving 20 participants were determined in two cases: Case A (arbitrary, controlled air-conditioner setting) and Case B (adjustment of 3 °C higher than the setting of Case A with cool bed linen). Data of indoor thermal comfort and electricity consumption were collected every night throughout the measurement period. Questionnaires on thermal comfort and sleep quality were distributed twice a night for a duration of three nights for each case; the first night was for respondents’ adaptation and the following two nights were for measurement. The sleep quality of the respondents was objectively measured using a commercially available activity tracker. Results found that most respondents were thermally comfortable in both cases, with 39% lower energy consumption reported for Case B compared to Case A. The thermal conditions of Case B were found to be more tolerable than those of Case A. Most respondents reported to have a calm and satisfied sleep for both cases. Comfort temperature and Sleep Efficiency Index (SEI) were found to be maintained in both cases.

The vehicle will generate an amount of current while the electric vehicle just starting to regeneratively brake. In order to avoid the impact of high current on the traction battery, a novel electrohydraulic hybrid electric vehicle has been proposed. The main power source is supplied by the electric drive system, and the hydraulic system performs the auxiliary drive system that fully exerts the advantages of the electric drive system and the hydraulic drive system. A proper regenerative braking control strategy is presented, and the control parameters are determined by the fuzzy optimization algorithm. The simulation analysis built the model through the united simulation of AMESim and MATLAB/Simulink. The results illustrated that the optimized control strategy can reduce battery consumption by 1.22% under NEDC-operating conditions.