• Energy Research

Graphene-metal composites have potential as novel catalysts due to their unique electrical properties. Here, we report the synthesis of a composite material comprised of monodispersed platinum nanoparticles on high-quality graphene obtained by using two different exfoliation techniques. The material, prepared via an easy, low-cost and reproducible procedure, was evaluated as an electrocatalyst for the hydrogen evolution reaction. The turnover frequency at zero overpotential (TOF0 in 0.1 m phosphate buffer, pH 6.8) was determined to be approximately 4600 h(-1). This remarkably high value is likely due to the optimal dispersion of the platinum nanoparticles on the graphene substrate, which enables the material to be loaded with only very small amounts of the noble metal (i.e., Pt) despite the very highly active surface. This study provides a new outlook on the design of novel materials for the development of robust and scalable water-splitting devices.

A transparent conductive graphene film is investigated as front contact in dye-sensitized solar cells (DSSCs), as an alternative to traditional transparent conducting oxides (TCO). The film is composed of poly-crystalline few-layers graphene, covering homogeneously an area of 1 cm2, deposited by chemical vapour deposition (CVD) technique on larger area Cu catalyst substrate and transferred on glass. DSSC photoanode is then fabricated, according to consolidated procedure, by sequential casting of TiO2 films through tape casting technique, followed by annealing at 500 °C, and sensitization with N719 dye. An outstanding value of photoconversion efficiency as high as 2% is recorded for the best cell, under one sun irradiation (AM 1.5 G, 100 mW cm-2), which is the highest ever reported for this kind of devices using graphene as front conducting film. Compared to previous results in the literature, the application of a large area continuous graphene film, guaranteed by the CVD deposition, definitely outperforms graphene layers composed by smaller graphene platelets (at micrometer scale). Morphological and electrical characterizations of graphene are reported and the functional performances of the best cell are compared with those obtained from classical DSSC exploiting fluorine-doped tin oxide. Obtained results encourage further investigation of graphene homogeneous thin film as viable alternative to standard TCOs for application in advanced devices, requiring high temperature processing or flexible substrates, incompatible with standard TCO films.

Two families of strongly luminescent silicon nanocrystals (SiNCs) cofunctionalized with dodecyl chains and pyrene chromophores perform as light-harvesting antennae and interact with carbon allotropes. The energy harvested in the SiNC core can thus be used to populate, for example, the lowest triplet excited state of C-60.

The growth of graphene by chemical vapor deposition on metal foils is a promising technique to deliver large-area films with high electron mobility. Nowadays, the chemical vapor deposition of hydrocarbons on copper is the most investigated synthesis method, although many other carbon precursors and metal substrates are used too. Among these, ethanol is a safe and inexpensive precursor that seems to offer favorable synthesis kinetics. We explored the growth of graphene on copper from ethanol, focusing on processes of short duration (up to one min). We investigated the produced films by electron microscopy, Raman and X-ray photoemission spectroscopy. A graphene film with high crystalline quality was found to cover the entire copper catalyst substrate in just 20 s, making ethanol appear as a more efficient carbon feedstock than methane and other commonly used precursors. (C) 2014 Elsevier B.V. All rights reserved.

Chemical vapor deposition (CVD) is widely utilized to synthesize graphene with controlled properties for many applications, especially when continuous films over large areas are required. Although hydrocarbons such as methane are quite efficient precursors for CVD at high temperature (similar to 1000 degrees C), finding less explosive and safer carbon sources is considered beneficial for the transition to large-scale production. In this work, we investigated the CVD growth of graphene using ethanol, which is a harmless and readily processable carbon feedstock that is expected to provide favorable kinetics. We tested a wide range of synthesis conditions (i.e., temperature, time, gas ratios), and on the basis of systematic analysis by Raman spectroscopy, we identified the optimal parameters for producing highly crystalline graphene with different numbers of layers. Our results demonstrate the importance of high temperature (1070 degrees C) for ethanol CVD and emphasize the significant effects that hydrogen and water vapor, coming from the thermal decomposition of ethanol, have on the crystal quality of the synthesized graphene.

Photoluminescence (PL) spectra were measured for dodecene-capped Si nanocrystals with a wide range of average diameters, from 1.8 to 9.1 nm. Nanocrystals larger than 3 nm exhibited relatively high PL quantum yields of 30%-45%. Smaller nanocrystals exhibited lower quantum yields that decreased significantly with reduced size. Because smaller nanocrystals also have lower optical absorption there is a significant biasing of the PL spectra by the larger nanocrystals. We show that with proper accounting of polydispersity and size-dependent quantum yields and optical absorption the effective mass approximation (EMA) accurately estimates the average diameter of silicon (Si) nanocrystals from experimentally determined PL emission peak energies. A finite confinement model is presented that explains the decreased PL quantum yields of the smaller diameter nanocrystals.

The interfacial structure in "giant" PbS/CdS quantum dots (QDs) was engineered by modulating the Cd:S molar ratio during in situ growth. The control of the gradient interfacial layer could facilitate hole transfer, regulate the transition from double- to single-color emission, as a consequence. These QDs are optically active close-to-the near-infrared (NIR) spectral region and are candidates as absorber materials in solar energy conversion. Photoinduced charge transfer from "giant" QDs to electron scavenger can still take place despite the ultra-thick (~5 nm) shell. The hybrid architecture based on a TiO2 mesoporous framework sensitized by the "giant" QDs with alloyed interface can produce a saturated photocurrent density as high as ~5.3 mA/cm2 in a photoelectrochemical (PEC) cell under 1 Sun illumination, which is around 2 times higher than that of bare PbS and core/thin-shell PbS/CdS QDs sensitizer. The as-prepared PEC device presented very good stability thanks to the "giant" core/shell QDs architecture with tailored interfacial layer and a further coating of the ZnS shell. 78% of the initial current density is kept after 2-h irradiation at 1 Sun. Engineering of electronic band structure plays a key role in boosting the functional properties of these composite systems, which hold great potential for H2 production in PEC devices.

The basic concept for efficiency improvement in dye-sensitized solar cells (DSSC) is limiting the electron-hole recombination. One way to approach the problem is to improve the photogenerated charge carriers lifetime and consequently reduce their recombination probability. We are reporting on a facile posttreatment of the mesoporous photoanode by using a colloidal solution of TiO2nanoparticles. We have investigated the outcome of the different sintering temperature of the posttreated photoanodes on their morphology as well as on the conversion efficiency of the DSSC. The DSSCs composed of posttreated photoanodes at 450°C showed an increase inJSCand consequently an increase in efficiency of 10%. Investigations were made to determine the electron recombination via the electrolyte by the OCVD technique. We found that the posttreatment has the effect of reducing the surface trap states and thus increases the electron lifetime, which is responsible for the increase of the overall cell efficiency.