• Energy Research
• Restricted close
• Embargo close
• 13. Climate action close
• 15. Life on land close
• 6. Clean water close
• 14. Life underwater close

Abstract Anaerobic digestion of animal by-products was investigated in batch and semi-continuously fed, reactor experiments at 55 °C and for some experiments also at 37 °C. Separate or mixed by-products from pigs were tested. The methane potential measured by batch assays for meat- and bone flour, fat, blood, hair, meat, ribs, raw waste were: 225, 497, 487, 561, 582, 575, 359, 619 dm 3 kg −1 respectively, corresponding to 50–100% of the calculated theoretical methane potential. Dilution of the by-products had a positive effect on the specific methane yield with the highest dilutions giving the best results. High concentrations of long-chain fatty acids and ammonia in the by-products were found to inhibit the biogas process at concentrations higher than 5 g lipids dm −3 and 7 g N dm −3 respectively. Pretreatment (pasteurization: 70 °C, sterilization: 133 °C, and alkali hydrolysis (NaOH) had no effect on achieved methane yields. Mesophilic digestion was more stable than thermophilic digestion, and higher methane yield was noticed at high waste concentrations. The lower yield at thermophilic temperature and high waste concentration was due to ammonia inhibition. Co-digestion of 5% pork by-products mixed with pig manure at 37 °C showed 40% higher methane production compared to digestion of manure alone.

Abstract With drastic fossil fuel depletion and environmental deterioration concerns, a move towards a more sustainable bioenergy-based economy is essential. Lately, the application of microwave (MW) irradiation for waste processing has been attracting interest globally. MW-assisted heating possesses several advantages such as the provision of high microwave energy into dielectric materials with deeper penetration for internal heat generation, showing beneficial features in improving the heating rate and reducing the reaction time. Consequently, the most recent literature regarding the applications of MW-assisted heating for biomass pretreatment as well as biofuel and bioenergy production was reviewed and consolidated in this study. An impressive increase in the product yield and improvement of the product properties are reported, with the use of MW-assisted heating in several conversion routes to produce biofuels. Despite being a promising technology for biofuel production, some major fundamental data of MW-assisted heating have not been comprehensively identified. Therefore, the feasibility of this technology for large-scale implementation is still subpar. Understanding the interaction between the feedstock and the microwave electromagnetic field, and the optimization of several operational and mechanical parameters are the two main keystones that would propel the industrialization of MW heating in the near future. This provides key insights leading to increased feasibility and more advanced application of MW heating.

In this paper, the performances of two iron-based syngas-fueled chemical looping (SCL) systems for hydrogen (H2) and electricity production, with carbon dioxide (CO2) capture, using different reactor configurations were evaluated and compared. The first investigated system was based on a moving bed reactor configuration (SCL-MB) while the second used a fluidized bed reactor configuration (SCL-FB). Two modes of operation of the SCL systems were considered, namely, the H2 production mode, when H2 was the desired product from the system, and the combustion mode, when only electricity was produced. The SCL systems were modeled and simulated using Aspen Plus software. The results showed that the SCL system based on a moving bed reactor configuration is more efficient than the looping system with a fluidized bed reactor configuration. The H2 production efficiency of the SCL-MB system was 11 % points higher than that achieved in the SCL-FB system (55.1 % compared to 44.0 %). When configured to produce only electricity, the net electrical efficiency of the SCL-MB system was 1.4 % points higher than that of the SCL-FB system (39.9 % compared to 38.5 %). Further, the results showed that the two chemical looping systems could achieve >99 % carbon capture efficiency and emit ~2 kg CO2/MWh, which is significantly lower than the emission rate of conventional coal gasification-based plants for H2 and/or electricity generation with CO2 capture.

The world, society and education are constantly evolving, and to respond to these changes, the main governmental institutions have been proposing different global strategies to focus efforts in the same direction. Currently, the United Nations and its 17 Sustainable Development Goals (SDG) have presented a series of indicators that could help to minimise the environmental, economic and social instability we are experiencing. In this sense, Education for Sustainable Development (ESD) has been described as a fundamental factor. Specifically, in previous work, we argued that physical education (PE) could be a good tool to contribute to SDGs. Based on this, no research analysing the voices of Physical Education Teachers (PET) on how this contribution could be made has been identified in previous literature. Therefore, the objectives of this research are: (1) to analyse the voices and opinions of active PETs in terms of the knowledge they have about Sustainable Development (SD); (2) to determine their opinions about the contribution that PE could make to SDGs; and finally, (3) to identify the challenges and limitations of pedagogical action of SD in PE. For this purpose, a qualitative analysis through a semi-structured interview with 41 active PETs was carried out. The main findings will be presented and discussed around four themes: (a) agreement on the concept of sustainability; (b) PE can contribute to the achievement of SDGs; (c) ambiguity in applying SDGs to PE lessons; and (d) teachers’ constraints on how to implement SDGs in PE. It seems to indicate that PETs do not have a multidimensional vision of sustainable development. While they recognise the potential of PE to contribute to SDGs through awareness raising and student learning, they point to its pedagogical and formative constraints as the main barriers to being able to contribute. They pointed to a lack of knowledge on how to do so, guidelines on how to integrate ESD, lack of involvement, shortage of time or resources in school physical education.

Diesel engine exhausts from a common rail 3.0 L F1C diesel engine were analyzed at two different load conditions of the WLTC testing cycle downstream of both the diesel particulate filter (DPF) and selective catalytic reactor (SCR) to verify their effect on the characteristics of carbon particulate matter. An array of chemical, physical and spectroscopic techniques (gas chromatography coupled with mass spectrometry (GC-MS), mobility analyzer, UV-Visible absorption and fluorescence spectroscopy) was applied for characterizing polycyclic aromatic hydrocarbons (PAH), heavy aromatic compounds and soot, constituting the particulate matter (PM) sampled from the exhaust. The engine was operated in half load (HL) (188 Nm, representing the more common condition for engine in urban traffic) and full load (FL) (452 Nm, representing the best performance of the engine operation) conditions, at the same engine speed (2000 rpm). Soot formation was enhanced in HL condition, with respect to FL, but, just because of the much lower soot amount, the after-treatment systems in this last condition resulted to be less efficient in the soot abatement. Indeed, the abatement through DPF was about 40% lower in the FL condition with respect to HL condition, and any significant further concentration decrease was found after SCR, in both conditions. By contrast, PAH concentration after DPF abatement was found to be higher in the HL with respect to FL condition. A further PAH concentration decrease of about 30% was found after the SCR in the HL condition whereas in FL the reduction was only about 5-6%. Also the heavy aromatic compounds having molecular weight above the GC-MS detection limit (300 u), were mitigated by SCR. Therefore, SCR did not cause a further soot reduction, whereas it was effective in largely reducing PAH and heavy aromatics emissions, especially in the lower temperature condition featuring the half-load condition, when combustion efficiency is worse. Moreover, SCR system reduced the emission of small particles probably due to an enhanced agglomeration of particles, with beneficial effect on the harmfulness to human health.

Climaps.eu is an online atlas providing data, visualizations and commentaries about climate adaptation debate. It contains 33 issue-maps and 5 issue-stories. Each of the maps focuses on one issue in the adaptation debate and provides.The atlas is addressed to climate experts (negotiators, NGOs and companies concerned by global warming, journalists…) and to citizens willing to engage with the issues of climate adaptation.It employs advanced digital methods to deploy the complexity of the issues related to climate adaptation and information design to make this complexity legible.

Cassava pulp is a major by-product produced in a cassava starch factory, containing 50–60% of starch (dry basis). Therefore, in this study we are considering its potential as a raw material substrate for the production of methane. To ensure sufficient amounts of nutrients for the anaerobic digestion process, the potential of co-digestion of cassava pulp (CP) with pig manure (PM) was further examined. The effect of the co-substrate mixture ratio was carried out in a semi-continuously fed stirred tank reactor (CSTR) operated under mesophilic condition (37 °C) and at a constant OLR of 3.5 kg VS m−3 d−1 and a HRT of 15 days. The results showed that co-digestion resulted in higher methane production and reduction of volatile solids (VS) but lower buffering capacity. Compared to the digestion of PM alone, the specific methane yield increased 41% higher when co-digested with CP in concentrations up to 60% of the incoming VS. This was probably due to an increase in available easily degradable carbohydrates as the CP ratio in feedstock increased. The highest methane yield and VS removal of 306 mL g−1 VSadded and 61%, respectively, were achieved with good process stability (VFA:Alkalinity ratio < 0.1) when CP accounted for 60% of the feedstock VS. A further increase of CP of the feedstock led to a decrease in methane yield and solid reductions. This appeared to be caused by an extremely high C:N ratio of the feedstock resulting in a deficiency of ammonium nitrogen for microbial growth and buffering capacity.

It is now environmentally desirable and legally mandatory to add renewable fuels such as ethanol or ethyl tert-butyl ether to gasoline. However, biofuels affect, among other properties, the distillation curve of gasoline, which is subject to strict regulations. This work presents a simple mathematical model capable of accurately predicting the influence that the addition of these oxygenates has on the distillation curve. In order to address this issue, it is essential to find a simple mathematical correlation between the boiling temperatures of the hydrocarbons present in gasoline and the properties (boiling temperature and volume or molar concentration of ethanol) of the corresponding azeotropic mixtures formed with ethanol. Power functions have been assumed to model the temperature composition diagrams of the vapour-liquid equilibrium. Experimental data previously published by these and other authors have been used to fit and validate the model. The results provided by the mathematical model can be of great interest to understand the process of fuel evaporation in spark-ignition engines or the adjustment of distillation cuts in refineries, in order to comply with the regulations, in terms of the distillation curve, after adding ethanol or ethyl tert-butyl ether.