• Energy Research
• Restricted close
• Embargo close
• 7. Clean energy close
• 14. Life underwater close

Abstract For the option of “carbon capture and storage”, an integrated assessment in the form of a life cycle analysis and a cost assessment combined with a systematic comparison with renewable energies regarding future conditions in the power plant market for the situation in Germany is done. The calculations along the whole process chain show that CCS technologies emit per kWh more than generally assumed in clean-coal concepts (total CO2 reduction by 72–90% and total greenhouse gas reduction by 65–79%) and considerable more if compared with renewable electricity. Nevertheless, CCS could lead to a significant absolute reduction of GHG-emissions within the electricity supply system. Furthermore, depending on the growth rates and the market development, renewables could develop faster and could be in the long term cheaper than CCS based plants. Especially, in Germany, CCS as a climate protection option is phasing a specific problem as a huge amount of fossil power plant has to be substituted in the next 15 years where CCS technologies might be not yet available. For a considerable contribution of CCS to climate protection, the energy structure in Germany requires the integration of capture ready plants into the current renewal programs. If CCS retrofit technologies could be applied at least from 2020, this would strongly decrease the expected CO2 emissions and would give a chance to reach the climate protection goal of minus 80% including the renewed fossil-fired power plants.

Petroleum-based fuels are used extensively as a result of the rising energy demands. Studies on fuels that will replace these fuels are now ongoing. In this study, performance, emission values of 4 different fuels at 4 different torque values were evaluated, and energy and exergy analyses were done utilizing combinations of gasoline, natural gas, and methanol. The tests employed a Lombardini LGW 523 2-cylinder 4-stroke engine. Four different fuels (gasoline, gasoline plus 50 g of natural gas, M20, and M20 plus 50 g of natural gas) were tested at a constant 3000 rpm with four different torque values (5, 10, 15, 20). In tests, it produced the lowest specific fuel consumption and the best emissions when combined with 50 g of natural gas fuel. The purpose of this study was to show that as torque increased, values for fuel, network, exhaust, absorption water, and energy destruction increased, while rates of lost energy decreased and rates of energy destruction increased.

An effective controller is proposed for the 'Photovoltaic(PV) - Battery - Diesel Generator(DG)' based hybrid standalone system in this article. A bidirectional DC to DC device which can allow power in both directions is integrated among the DC-link and battery bank to maintain contact voltage by maintaining power balance in the system. Further, a bidirectional inverter is also considered between point of common coupling (PCC) and DC-link for providing supply to AC loads as well as charging the battery from diesel generator based on requirement. However, the phenomenon of partial shading condition (PSC) commonly occurring on PV modules and also generated power from PV always fluctuates according to changes in weather. To achieve a superior performance of the system, a Takagi-Sugeno Fuzzy (TSF) based controllers are implemented in proposed control schemes. The novel control schemes are implemented on a bidirectional DC to DC converter as well as three phase bidirectional inverter. However, the proper deloading process of the PV system should be incorporated into the controller of the DC to DC converter to achieve power balance during light load conditions. Balanced quality voltages (3-phase) at PCC are achieved by inverter control which forces to maintain balanced currents generated by DG during the operation of unbalanced loads. Maintaining balanced DG currents can help to reduce the oscillations on the torque of the shaft which increases the fatigue life. Further the reactive power demanded at PCC is compensated by the inverter control, hence DG need not to provide it which results can reduce the consumption of diesel. Various case studies are examined by using MATLAB to present results and Real Time Digital Simulator (RTDS) based results are also provided in this paper.

Abstract Mediterranean islands have the advantage of favourable climatic conditions to use different marine renewable energy sources. Remote sensing can provide data to determine wind energy production potential and observational activity to identify, assess and detect suitable points in large marine areas. In this paper, a new combined model has been developed to integrate wind speed assessment, mapping and forecasting using Sentinel 1 satellite data through images processing and Adaptive Neuro-Fuzzy Inference System and the Bat algorithm. Synthetic Aperture Radar (SAR) satellite images from the Sentinel 1 satellite have been used in order to detect offshore and nearshore wind potential. Particularly, Sentinel 1 images have been analysed by means of the SNAP software. Then, to extract data about wind speed and direction, a GIS software for mapping the wind climate has been used. This new methodology has been applied to the North-Central coasts of Sardinia Island and then focused on six main small islands of La Maddalena archipelago. Furthermore, ten Hot Spots (HSs) have been identified as interesting because of their high-energy potential and the possibility to be considered as sites for future implementation of Wind Turbine Generators (WTGs). Finally, the ten identified HS have been used as input data to train and test the proposed forecast model.

In the present work, the supercritical water gasification (SCWG) of biomass is analyzed with a view to outlining the possible thermodynamic constraints that must be taken into account to develop this new process. In particular, issues concerning the formation of solid carbon and the process heat duty are discussed. The analysis is conducted by means of a two-phase non-stoichiometric thermodynamic model, based on Gibbs free energy minimization. Results show that char formation at equilibrium only occurs at high biomass concentrations, with a strong dependence on biomass composition. As regards the process heat duty, SCWG is mostly endothermic when biomass concentration is low, although a very small amount of oxidizing agent is able to make the process exothermic, with only a small loss in the heating value of the syngas produced.

Abstract Thermal energy storage (TES) will improve the efficiency and output of solar power plants. TES based on thermochemical cycles is an interesting option as thermochemical cycles can provide high energy storage densities and allow longer heat storage time. The use of multivalent solid oxide reduction–oxidation (REDOX) reactions for thermochemical heat storage is a promising option. Several concepts are feasible for coupling solar energy to the redox reaction. Among those a directly irradiated rotary kiln is one of the most interesting because it is able to provide high mass flow rates and high amounts of active material. A solar-heated rotary kiln was set-up and operated in the solar furnace of DLR for thermal reduction and oxidation of cobalt oxide. The redox material was fed into the reactor batch wise and reduced on-sun at temperatures of about 900 °C and re-oxidized off-sun in the same rotary kiln. Both steps were carried out in an air atmosphere. Thirty cycles were performed with one batch showing no evident degradation of the material. The results confirm that the rotary kiln is a feasible reactor set-up for the solar reduction of metal oxides and, hence, for thermochemical energy storage.

The performance and behavior of five unglazed solar collector installations, devoted to the heating of five outdoor swimming pools located in Switzerland, is studied on the basis of experimental data collected in 1988. Due to the low temperatures involved, hourly efficiencies often exceed 80%. The mean daily collector efficiency is of the order of 60% in optimal conditions and is in good agreement with the G3 simulation program.

The aim of the joint activity between CNR ITAE and University of Malta, funded in the framework of a bilateral agreement is the preliminary study of the possible application of thermally-activated technologies for the refrigeration of fish on-board of fishing vessels, with particular attention to the Mediterranean area. In such a context, the two partners, given their expertise in the adsorption and absorption cooling technologies, dedicated the first year of the joint project on several activities needed to define possible integration solutions on-board. The following report is then organized as follows: - Section 3 reports an analysis of the state-of-the-art concerning existing refrigeration systems currently employed in the fishing vessels' application as well as innovative activities recently performed on the possible integration of thermally-driven technologies for the refrigeration. - Section 4 focuses on the definition of possible integration between the waste heat recovered from the engines of the fishing vessel and the sorption technology for refrigeration. This analysis takes into account different possible applications, in terms of refrigeration temperatures as well as capacities. Furthermore, different possible waste heat streams at different temperature levels are investigated. - Section 5 identifies the typical working boundary conditions under which the fishing vessel operates, in terms of cooling demand, also considering different climatic zones (i.e. different geographical areas in which the vessel operates) and vessels' typology. - Section 6 investigates possible working pairs, both for adsorption and absorption technologies, which are promising for the given boundary conditions in Section 5. This activity is needed to set the operational limits that each technology and working pair cannot overcome. - Section 7 reports the calculations performed for each working pair and operating conditions, both taking into account thermodynamic constraints as well as analysing literature results on different prototypes realized and tested. - Section 8 introduces a dynamic model, implemented in TRNSYS environment, of an absorption refrigerator, which was validated and will be used in the following activities to investigate the defined schematics in Section 4. - Section 9 defines the Key Performance Indicators (KPIs) that will be used in the following activities to compare the achievable results of the different configurations.