• Energy Research
• Closed Access close
• Tsinghua University close

Abstract A great deal of heat is wasted in intensive public shower facilities, such as those in schools, barracks and natatoriums, which open up at specified time. It will contribute a lot to energy saving and environmental protection with significant economic benefits to recycle the exhaust heat. In this paper, we propose two different kinds of heat pumps (an electric heat pump and an absorption heat pump) in the heat recovery systems. In both system, the used shower water is drained through a pipe and collected in a gray water pool. When the wastewater reaches certain volume, the heat pump system will begin working and recycling heat. The wastewater is filtered and piped to the heat exchanger to exchange heat with the tap water whose temperature will increase from 12 °C to 25 °C with the wastewater temperature dropping from 30 °C to 17 °C. Then the wastewater is piped to the heat pump evaporator and the tap water is piped to the condenser for farther heating. According to the different characteristics of the electric heat pump and absorption heat pump, we also introduce the processes and control methods of different heat recovery systems in details in this paper. Based on a practical example, this paper analyzes and compares the economic and environmental benefits of three retrofitting schemes, including “exhaust heat recovery using electric heat pump”, “exhaust heat recovery using electric heat pump + gas boiler” and “exhaust heat recovery using direct-fired heat pump”. Then we find out that the heat recovery system using direct-fired absorption heat pump has lower energy consumption, less pollution, lower operating cost, and shorter payback period. And it has a promising practical application.

Abstract The central role of occupants for achieving energy savings in residential buildings is increasingly recognised. Simulation programmes able to take into account occupant behaviour are considered to be powerful tools for bridging the gap between the predicted and the actual energy consumption for new buildings. Nevertheless, the majority of residential buildings that will constitute the housing stock in 2050 have already been built today, therefore occupant behaviour and building simulation tools need to be fully exploited for supporting the renovation of existing housing stock. The aim of this paper is to explore the role of occupant behaviour modelling in supporting decision-makers dealing with the design of renovation strategies for residential buildings. An Italian multi-family public housing building is assumed as case study to estimate the influence of three dimensions linked with occupant behaviour – management of the thermostat, management of the heating system, variation of building characteristics – on energy heating consumption. The results show that, while the occupant behaviour influences the heating loads up to 1/3 in case of high level of building retrofit, the less the building is renovated, the higher is the behavioural impact in absolute terms of energy reduction. Therefore, in order to be effective, renovation strategies are required to design appropriate informative instruments at an early stage to support behaviour changes towards responsible energy consumption.

In order to enhance the efficiency and benefits of the sludge anaerobic digestion process, K2FeO4 was added to a sludge anaerobic digestion system, and its effects on the system were comprehensively investigated. Results showed that sludge anaerobic digestion was greatly improved by adding 500 mg/L K2FeO4. Biogas and methane productions were increased by 26.6 and 28.4%, respectively. Sludge reduction, protein removal, and the conversion efficiency of dissolved organics were all improved. The mechanism revealed that the disintegration of sludge flocs, enhancement of protease activity, and decrease of soluble sulfide toxicity on microorganisms contributed to biogas production and sludge reduction. Biogas quality was improved, benefitting from the decreasing H2S content in biogas; as additionally, the cost of biogas desulfuration was reduced. In the biogas slurry treatment, the PO43--P concentrations were decreased by 39%, which also reduced the cost of the dephosphorization processes at certain extent.

Abstract This paper presents a numerical study of the particle cluster behavior in a riser/downer reactor by means of combined computational fluid dynamics (CFD) and discrete element method (DEM), in which the motion of discrete particles is obtained by solving Newton's equations of motion and the flow of continuum gas by the Navier–Stokes equations. It is shown that the existence of particle clusters, unique to the solid flow behavior in such a reactor, can be predicted from this first principle approach. The results demonstrate that there are two types of clusters in a riser and downer: one is in the near wall region where the velocities of particles are low; the other is in the center region where the velocities of particles are high. While the extent of particle aggregation appears to be similar, the duration time for the first type in a downer is shorter than in a riser. Furthermore, it is demonstrated that the formation of clusters is affected by a range of variables related to operational conditions, particle properties, and bed properties and geometry. The increase of solid volume fraction, sliding and rolling friction between particles or between particles and wall, or damping coefficient can enhance the formation of clusters. The use of multi-sized particles can also promote the formation of clusters. But the increase of gas velocity or use of a wider bed can suppress the formation of clusters. The van der Waals force may enhance the formation of clusters when solid concentration is high but suppress the formation of clusters near the wall region when solid concentration is low.

Abstract Natural gas vehicles offer the benefits of reducing oil use, CO2 emissions and air pollutants. Promoting the use of natural gas vehicles is considered as one of the most important strategies towards sustainable transportation. China made remarkable progress in promoting natural gas vehicles over recent years, and its 4.6 million natural gas vehicles in 2014 represented the world׳s largest natural gas vehicle fleet. In this paper, the development of natural gas vehicles in China is reviewed based on a triple-perspective (Fuel-Vehicle-Infrastructure) technical–economical framework. The review indicates that (a) pricing of vehicle-use Compressed Natural Gas (CNG) and Liquefied Natural Gas (LNG) is essential in determining natural gas vehicle development. A pricing principle similar to the fixed CNG/gasoline price ratio (0.75:1) should be applied to LNG/diesel price ratio; (b) for CNG passenger vehicles, the modified CNG vehicles, with ¥3000–5000 additional cost, is more attractive to consumers than originally manufactured CNG vehicles, with about ¥10,000 additional cost. Vehicle retrofit should be permitted by the government with the precondition that retrofit standards are strictly enforced; (c) for CNG/LNG transit buses, the deployment is strongly affected by local government׳s preference. In regions with sufficient natural gas supply, the government should prioritize the deployment of CNG/LNG transit buses rather than other technologies; (d) for LNG commercial vehicles, with ¥60,000–80,000 higher cost than their counterpart diesel vehicles, financial incentive is critical for their development. China׳s current vehicle subsidy scheme should be extended to cover LNG commercial vehicles; (e) regarding refueling infrastructures, interference with urban land-use planning and long-time administrative approval are the major barriers. Local governments should launch dedicated plans and strategies to support the further deployment of CNG/LNG refueling infrastructures.

Abstract In this paper, a finned heat pipe assisted passive heat sink based on a newly emerging high performance phase change material (PCM), the low melting point metal (LMPM), was developed for thermal buffering of high power electronics which works intermittently with heat generation rate up to 1000 W (10 W/cm2). Firstly, thermal performances of the PCM heat sink under different thermal shocks (from 200 W to 1000 W) were experimentally evaluated, in comparison with that of an organic PCM which has similar melting point. It was found that, the former one can prolong the working duration 1.4–2.4 times that of the latter one. Then, the performance of the heat sink was improved through reducing the contact thermal resistance and by increasing the fin number. Furtherly, an air cooling radiator was configured to accelerate the solidification process of the PCM module, which makes it capable of maintaining its highest temperature below 85 °C under 1000 W periodic thermal shock (10 min on and 15 min off). Moreover, energy dispersive spectrometer (EDS) analysis was conducted to verify the compatibility of the LMPM PCM and the structural materials. Finally, a simplified numerical model was developed and validated for the currently constructed finned heat pipe assisted LMPM PCM heat sink, which can be much helpful for future practical thermal design and optimization of this kind of thermal buffering module.