• Energy Research
• 7. Clean energy close
• CA close
• Energy Research close

Production of biodiesel from yellow grease (waste cooking oil and waste animal fats) is fast emerging as a promising alternative to address the twin challenges before the biodiesel industry today-fluctuation in prices of vegetable oil and the food versus fuel debate. Yellow grease has a high percentage of free fatty acids (FFA) and proves to be an unsuitable feedstock for biodiesel production from commercially viable alkali-catalyzed production systems due to saponification problems.“Green” methodologies based on heterogeneous solid acid catalyzed reactions have the potential to simultaneously promote esterification and transesterification reactions of yellow grease to produce biodiesel without soap formation and offer easy catalyst separation without generation of toxic streams. This paper presents kinetic studies for the conversion of model yellow grease feeds to biodiesel using a heteropolyacid supported on alumina (HSiW/Al2O3) using a batch autoclave. Three model yellow grease feeds were prepared using canola oil with added FFA such as palmitic, oleic and linoleic acid. A pseudo homogeneous kinetic model for the parallel esterification and transesterification was developed. The rate constants and activation parameters for esterification and transesterification reactions for the model yellow grease feeds were determined. The rate constants for esterification are higher than the transesterification rate constants. The kinetic model was validated using the experimental biodiesel data obtained from processing a commercial yellow grease feed. The kinetic model could be used to design novel processes to convert various low-value waste oils, fats and non-food grade oils to sustainable biodiesel. Keywords: Yellow grease, Canola oil, Free fatty acids, Heteropolyacid, Kinetics for esterification and transesterification

The benefits of aluminum lamination in improving the physical and mechanical properties of wood-based composites is now well documented. This paper shows the contribution of life cycle assessment (LCA) as a tool to assess and compare the environmental footprint in the development of laminated panels. SimaPro 9.0 software, using Ecoinvent database was used to analyze the environmental impacts associated with the manufacturing of wood aluminum-laminated (WAL) panels and aluminum honeycomb panel (AHP). The impact 2002+ method was used to estimate environmental impacts. The LCA results show that the WAL panels manufacturing had a lower environmental impact than AHP manufacturing. In term of product, wood-based composites were the best choice as a core in laminated panel manufacturing. Wood-based composite manufacturing showed environmental advantages in all damage categories except in ecosystem quality. Aluminum alloy sheets manufacturing played an important role in the generation of environmental impacts for laminated panel development.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

This article proposes an effective evolutionary hybrid optimization method for identifying unknown parameters in photovoltaic (PV) models based on the northern goshawk optimization algorithm (NGO) and pattern search (PS). The chaotic sequence is used to improve the exploration capability of the NGO algorithm technique while evading premature convergence. The suggested hybrid algorithm, chaotic northern goshawk, and pattern search (CNGPS), takes advantage of the chaotic NGO algorithm’s effective global search capability as well as the pattern search method’s powerful local search capability. The effectiveness of the recommended CNGPS algorithm is verified through the use of mathematical test functions, and its results are contrasted with those of a conventional NGO and other effective optimization methods. The CNGPS is then used to extract the PV parameters, and the parameter identification is defined as an objective function to be minimized based on the difference between the estimated and experimental data. The usefulness of the CNGPS for extraction parameters is evaluated using three distinct PV models: SDM, DDM, and TDM. The numerical investigates illustrate that the new algorithm may produce better optimum solutions and outperform previous approaches in the literature. The simulation results display that the novel optimization method achieves the lowest root mean square error and obtains better optima than existing methods in various solar cells.

This paper presents an experimental study of indoor thermal environment near a full-scale glass facade with different types of shading devices under varying climatic conditions in winter. Interior glazing and shading temperature, operative temperature and radiant temperature asymmetry were measured for facade sections with roller shades and venetian blinds at different positions. Interior glass surface temperatures can be high during sunny days with low outdoor temperature. Shading systems significantly improved operative temperature and radiant temperature asymmetry during cold sunny days, depending on their properties and tilt angle. During cloudy days the impact was smaller, however the shading layers could still decrease the amount of heat loss through the facade. A transient building thermal model, which also calculates indoor environmental indices under the presence of solar radiation, was developed and compared with the experimental measurements. Part II of this paper uses this validated model with a transient, two-node thermal comfort model (including transmitted solar radiation) for assessment of indoor environmental conditions with different building envelope and shading properties, facade location and orientation.

A vehicle model is used to evaluate a novel powertrain that is comprised of a dual energy storage system (Dual ESS). The system includes two battery packs with different chemistries and the necessary electronic controls to facilitate their coordination and optimization. Here, a lithium-ion battery pack is used as the primary pack and a Zinc-air battery as the secondary or range-extending pack. Zinc-air batteries are usually considered unsuitable for use in vehicles due to their poor cycle life, but the model demonstrates the feasibility of this technology with an appropriate control strategy, with limited cycling of the range extender pack. The battery pack sizes and the battery control strategy are configured to optimize range, cost and longevity. In simulation the vehicle performance compares favourably to a similar vehicle with a single energy storage system (Single ESS) powertrain, travelling up to 75 km further under test conditions. The simulation demonstrates that the Zinc-air battery pack need only cycle 100 times to enjoy a ten-year lifespan. The Zinc-air battery model is based on leading Zinc-air battery research from literature, with some assumptions regarding achievable improvements. Having such a model clarifies the performance requirements of Zinc-air cells and improves the research community's ability to set performance targets for Zinc-air cells.

Energy management is an enabling technique to guarantee the reliability and economy of hybrid electric systems. This paper proposes a novel machine learning-based energy management strategy for a hybrid electric bus (HEB), with an emphasized consciousness of both thermal safety and degradation of the onboard lithium-ion battery (LIB) system. Firstly, the deep deterministic policy gradient (DDPG) algorithm is combined with an expert-assistance system, for the first time, to enhance the “cold start” performance and optimize the power allocation of HEB. Secondly, in the framework of the proposed algorithm, the penalties to over-temperature and LIB degradation are embedded to improve the management quality in terms of the thermal safety enforcement and overall driving cost reduction. The proposed strategy is tested under different road missions to validate its superiority over state-of-the-art techniques in terms of training efficiency and optimization performance.

In this paper, fault prognosis of aircraft jet engines are considered using computationally intelligent-based methodologies to ensure flight safety and performance. Two different dynamic neural networks namely, the nonlinear autoregressive neural networks with exogenous input (NARX) and the Elman neural networks are developed and designed for this purpose. The proposed dynamic neural networks are designed to capture the dynamics of two main degradations in the jet engine, namely the compressor fouling and the turbine erosion. The health status and condition of the engine is then predicted subject to occurrence of these deteriorations. In both proposed approaches, two scenarios are considered. For each scenario, several neural networks are trained and their performance in predicting multi-flights ahead turbine output temperature are evaluated. Finally, the most suitable neural network for prediction is selected by using the normalized Bayesian information criterion model selection. Simulation results presented demonstrate and illustrate the effective performance of our proposed neural network-based prediction and prognosis strategies.

Abstract Recharging infrastructure (RI) deployment plays a vital role in improving the public recharging availability for transport electrification. Decarbonizing transportation using low-emission electricity requires massive RI network. Even though the consumers are reluctant to purchase electric vehicles (EVs) until RIs are sufficiently placed, the investors are not willing to invest in RIs due to recharging demand uncertainties. Therefore, a scientific planning framework is needed to ensure the sustainable deployment of EV-RIs in complex networks. In this study, a lifecycle thinking-based multi-period infrastructure-planning framework is proposed to develop sustainable public EV-RIs in an urban context. This framework consists of a temporal model to find the dynamic EV-RI demands, a stochastic model to obtain travel distances, and a multi-objective optimization model to select the best desirable capacities and locations for potential EV-RIs. A case study of a typical medium-scale municipality in Canada was assessed using the proposed framework and validated using conventional infrastructure planning scenarios. The geo-processing data, regional travel behaviors, and recharging characteristics were used as model inputs. The results of the case study showed that the proposed framework can be used to estimate multi-period public recharging demands, minimize lifecycle costs, maximize service coverage and infrastructure utilization, and ensure reasonable paybacks compared to conventional planning approaches. Moreover, this framework can be used to compare different investment assistances, which are required in the early stages of the RI deployment process to encourage investors. Furthermore, government and private institutions can use this framework to identify recharging demands, permitting, and developing RIs in the long-run.