• Energy Research
• 7. Clean energy close
• AU close
• BE close

In Belgium, and many other countries, rooftop solar panels are becoming a ubiquitous form of decentralised energy production. The increasing share of these distributed installations however imposes many challenges on the operators of the low-voltage distribution grid. They must keep the voltage levels and voltage balance on their grids in check and are often regulatory required to provide sufficient reception capacity for new power producing installations. By placing solar panels in different inclinations and azimuth angles, power production profiles can possibly be shifted to align more with residential power consumption profiles. In this article, it is investigated if the orientation of solar panels can have a mitigating impact on the integration problems on residential low voltage distribution grids. An improved simulation model of a solar panel installation is constructed, which is used to simulate the impact on a residential distribution grid. To stay as close to real-life conditions as possible, real irradiation data and a model of an existing grid are used. Both the developed model as the results on grid impact are evaluated.

In this paper, a comparison of power system frequency response is conducted for a simple modelled power system with primary frequency control being provided either by synchronous generators or by inverter-based Battery Energy Storage (BES) systems. Mathematical models of conventional governor and turbine are developed, representing conventional synchronous generator frequency control, and are used to illustrate system frequency response for a range of typical conventional generating units. A mathematical model of a power-electronics interfaced Li-ion BES system is developed and used to represent a non-synchronous inverter-based generator with primary frequency control capabilities. MATLAB/Simulink is used to build a model of a small power system, and simulations are carried out with at a range of typical conventional synchronous generating units with a nonsynchronous generating unit in the power system. The simulation results demonstrate that the BES can be used for primary frequency control providing a faster and better response. BES is also capable of almost eliminating frequency overshoot and reducing 70% of settling time while providing primary frequency control in power system with various types of conventional synchronous generating units and a nonsynchronous generating unit.

Abstract To improve the conversion efficiency of thermophotovoltaic devices, we designed a thermophotovoltaic system based on an InAs/InGaAsSb/GaSb three-junction tandem cell. The tandem cell can recover photons in the wavelength range of 200–3650 nm and therefore enhance the output power of the system. To further improve system performance, we designed a multilayer circular truncated cone metamaterial emitter matching the tandem cell. Existing TPV systems based on multi-junction tandem PV cells can achieve conversion efficiencies of 33.3%–41%, while the thermophotovoltaic system coupled with the multilayer circular truncated cone metamaterial can recover more photons of 1.44 mol/(m2·s) and achieve a higher conversion efficiency of 52.8% at 1773 K. The thermophotovoltaic system designed here demonstrates an extremely high energy conversion efficiency and has good application prospects.

The synthesis of biodiesel from Jatropha curcas by transesterification is kinetically controlled. It depends on the molar ratio, reaction time, and temperature, as well as the catalyst nature and quantity. The aim of this study was to explore the transesterification of low-cost, inedible J. curcas seed oil utilizing both homogenous (potassium hydroxide; KOH) and heterogenous (calcium oxide; CaO) catalysis. In this effort, two steps were used. First, free fatty acids in J. curcas oil were reduced from 12.4 to less than 1 wt.% with sulfuric acid-catalyzed pretreatment. Transesterification subsequently converted the oil to biodiesel. The yield of fatty acid methyl esters was optimized by varying the reaction time, catalyst load, and methanol-to-oil molar ratio. A maximum yield of 96% was obtained from CaO nanoparticles at a reaction time of 5.5 h with 4 wt.% of the catalyst and an 18:1 methanol-to-oil molar ratio. The optimum conditions for KOH were a molar ratio of methanol to oil of 9:1, 5 wt.% of the catalyst, and a reaction time of 3.5 h, and this returned a yield of 92%. The fuel properties of the optimized biodiesel were within the limits specified in ASTM D6751, the American biodiesel standard. In addition, the 5% blends in petroleum diesel were within the ranges prescribed in ASTM D975, the American diesel fuel standard.

Energy storage is becoming increasingly important, both to mitigate intermittency in renewable generation and to reduce peak demand. However, storage remains expensive and so must be managed optimally. This paper considers the optimal management of storage that is subject to inefficiency in charging/discharging and to self-discharge, with the objective of minimizing energy costs. Notably, it shows that the less efficient the storage is, the less capacity is required to achieve the maximum peak-shaving benefit.

This paper studies a closed loop linear control system. The sensor computes a state estimate and sends it to the controller/actuator in the receiver block over a randomly fading packet dropping link. The receiver sends an ACK/NACK packet to the transmitter over a link. It is assumed that the transmission energy per packet at the sensor depletes a battery of limited capacity, replenished by an energy harvester. The objective is to design an optimal energy allocation policy and an optimal control policy so that a finite horizon LQG control cost is minimized. It is shown that in case the receiver to sensor feedback channel is free of errors, a separation principle holds. Hence, the optimal LQG controller is linear, the Kalman filter is optimal and the optimal energy allocation policy is obtained via solving a backward dynamic programming equation. In case the feedback channel is erroneous, the separation principle does not hold. In this case, we propose a suboptimal policy where the controller still uses a linear control, and the transmitter minimizes an expected sum of the trace of an “estimated” receiver state estimation error covariance matrix. Simulations are used to illustrate the relative performance of the proposed algorithms and various heuristic algorithms for both the perfect and imperfect feedback cases. It is seen that the dynamic programming based policies outperform the simple heuristic policies by a margin.

As the wind farm sector grows and becomes an established renewable energy source, it introduces new materials, technologies and processes that expose workers to increased and unique occupational risks. In this paper, we performed a generic review of scientific and industry literature on online scientific databases and search engines to identify the extent to which occupational health hazards and risks specific to wind farms have been considered. Our review revealed noise, electromagnetic fields, shadow flicker, epoxy and styrene and physical stress have been the focus of limited research, mainly including self-reported data from offshore wind farm employees. Factors such as vibration, welding fumes and other possibly harmful substances, weather conditions and biological hazards have not been addressed by studies, although their presence and combinations could be of concern. Therefore, there is a need for further research on unique and combined risks and hazards faced by workers across all lifecycle stages of wind energy production. This would improve knowledge and provide the opportunity to manage health hazards in current and newly constructed installations and inform future regulatory and other preventative measures.

In this chapter, turbulent flow of water-based optimization (TFWO) inspired based on whirlpools created in turbulent flow of water is used to solve the maximum power point tracking (MPPT) of photovoltaic systems in partial shading conditions. The TFWO is used to determine the optimal duty cycle of the DC/DC converter with the objective of maximizing the extracted power of the photovoltaic system. The capability of proposed method is evaluated in different patterns of partial shading to achieve global optimal power. The simulation results showed that TFWO is able to track the global maximum power point (GMPP), successfully in PSC and also fast climate changing. The TFWO has a better tracking capability with faster tracking speed and accuracy than particle swarm optimization (PSO) in obtaining the GMPP. Moreover, the results indicate that the use of buck–boost converter led to faster and more accurate access to the global optimal point than the system equipped with boost converter. The results showed that photovoltaic system with boost converter cannot obtain global maximum power in climate changing condition and limited the efficiency of the MPPT algorithm, while the photovoltaic system with buck–boost converter could be tracked GMPP due to its wider operating area.