• Energy Research
• 2016-2025close
• US close
• GB close
• CA close
• BG close

Abstract Fractures along interfaces between host rock and wellbore cement have long been identified as potential CO2 leakage pathways from subsurface CO2 storage sites. As a consequence, cement alteration due to exposure to CO2 has been studied extensively to assess wellbore integrity. Previous studies have focused on the changes to either chemical or mechanical properties of cement upon exposure to CO2-enriched brine, but not on the effects of loading conditions. This paper aims to correct this deficit by considering the combined effects of the fracture pathway and changing effective stress on chemical and mechanical degradation at conditions relevant to geologic carbon storage. Flow-through experiments on fractured cores composed of cement and tight sandstone caprock halves were conducted to study the alteration of cement due to exposure to CO2-enriched brine at 3, 7, 9, and 12 MPa effective stress. We characterized relevant reactions via solution chemistry; fracture permeability via changes to differential pressure; mechanical changes via micro-hardness testing, and pore structure changes via x-ray tomography. This study showed that the nature and the rates of the chemical reactions between cement and CO2 were not affected by the effective stress. The differences in the permeability responses of the fractures were attributed to interactions among the geometry of the flow path, the porosity increase of the reacted cement, and the mechanical deformation of reacted asperities. The suite of observed chemical reactions contributed to change in cement mechanical properties. Compared to the unreacted cement, the average hardness of the amorphous silica and depleted layers was decreased while the hardness of the calcite layer was increased. Tomographic imaging showed that preferential flow paths formed in some of the core-flood experiments, which had a significant impact on the permeability response of the fractured samples. We interpreted the observed permeability responses in terms of competition between dissolution of cement phases (leading to enhanced permeability) and mechanical deformation of reacted regions (leading to reduced permeability).

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

As the concern with global warming increases causing the need for CO2 reduction, renewable energy is of great interest as it has lower carbon footprint when compared to conventional sources (natural gas, coal, oil and nuclear). Solar energy has been drawing worldwide attention since it can transform sunlight directly into electricity with the use of photovoltaic (PV) cells. However, this technology has some drawbacks that need to be addressed including dust deposition on solar panels, also known as soiling. Soiling can decrease PV panel's efficiency thereby resulting in less energy production. The soiling rates are very site specific and depend on the geographic location of the panels and the climate in that area. The solar panels can be cleaned naturally (by rainfall, snow or wind) or mechanically washed. This thesis addresses the impact of solar panel soiling and washing on the energy production of solar PV plants located at the UNLV campus. The objectives of this project were (a) to evaluate whether rainfall alone, in the desert environment with low rainfall, is sufficient to clean up the solar panels, and, if possible, determine the minimum amount of rainfall necessary to clean up panels.; (b) to examine the efficiency loss caused by soiling using different methods of analyses and (c) to evaluate if panel washing is worthwhile given the cost and the efficiency gain that is obtained by washing. To calculate the efficiency of the panels, a model was developed to generate parameters that were not measured at the site. Panel efficiencies before and after rainfall events were compared to determine the minimum amount of rain necessary to clean the panels. It was found that at least 0.2 inches of rain was needed to partially restore clean-panel efficiency. In Las Vegas, the recurrence periods of different depths rainfall were calculated using data from the past 29 years. It was observed that the 50th percentile recurrence period of a rainfall event with depth of 0.2 inches or higher was approximately 52 days. Student Union: -0.0044%/day, CBC-C: -0.00099%/day, and Dayton Hall: -0.0034%/day The amount of efficiency lost during the dry intervals (periods between rainfall events) was analyzed in three different ways. The average efficiency loss per day during the dry periods varied from -0.000171 % to -0.00533 %, depending on the method used and the building where the panels were located. However, there were some limitations to the calculations. It was not possible to completely isolate the effects of only soiling on the efficiency of the panels. The rate of decline seemed to be also impacted by seasonal effects. To better evaluate the effect of washing, a professional company was hired to wash a set of solar panels located on UNLV's Student Union building. The panels were washed with water with a low concentration of TDS. The power output and the efficiency of those panels were analyzed from before and after the washing. There was a very small efficiency and power increase due to the washing. Therefore, it was concluded that washing in this area is not worthwhile, and that rainfall events in excess of 0.2 inches can adequately restore the efficiency of the panels. If there is a change in cost of energy, washing, water or a great increase in the efficiency of the solar panels, it would be necessary to reevaluate the analysis.

Abstract. Flooding in the Amazon basin is frequently attributed to modes of large-scale climate variability, but little attention is paid to how these modes influence the timing and duration of floods despite their importance to early warning systems and the significant impacts that these flood characteristics can have on communities. In this study, river discharge data from the Global Flood Awareness System (GloFAS 2.1) and observed data at 58 gauging stations are used to examine whether positive or negative phases of several Pacific and Atlantic indices significantly alter the characteristics of river flows throughout the Amazon basin (1979–2015). Results show significant changes in both flood magnitude and duration, particularly in the north-eastern Amazon for negative El Niño–Southern Oscillation (ENSO) phases when the sea surface temperature (SST) anomaly is positioned in the central tropical Pacific. This response is not identified for the eastern Pacific index, highlighting how the response can differ between ENSO types. Although flood magnitude and duration were found to be highly correlated, the impacts of large-scale climate variability on these characteristics are non-linear; some increases in annual flood maxima coincide with decreases in flood duration. The impact of flood timing, however, does not follow any notable pattern for all indices analysed. Finally, observed and simulated changes are found to be much more highly correlated for negative ENSO phases compared to the positive phase, meaning that GloFAS struggles to accurately simulate the differences in flood characteristics between El Niño and neutral years. These results have important implications for both the social and physical sectors working towards the improvement of early warning action systems for floods.

Abstract Adsorbent-based carbon capture is only feasible if adsorption-desorption cycles are both fully regenerating and efficient. This work proposes a regenerative pH swing process and a pH swing regenerative adsorbent that are inspired by natural CO2 conversion by carbonic anhydrase biocatalysts found in mammalian red blood cells. The main objective is to develop, test and analyze a synthetic pH Swing Adsorption (pHSA) system as well as a pHSA compatible solid adsorbent to capture CO2 from a simulated ambient air gas stream. The lead developed adsorbent is a carbon black co-activated with potassium carbonate and nitrogenous copolymer that is impregnated with immobilized bovine carbonic anhydrase and thereby deemed “BCA/KN-CB”. BCA/KN-CB has preliminarily demonstrated both competitive CO2 adsorption capacity and limited regenerative ability under experimental pHSA conditions. In addition, BCA-based adsorbents achieved higher adsorption capacities than non-BCA adsorbent counterparts. The BCA/KN-CB adsorbent displayed both large point of zero charge (PZC) swings and regenerative stability. The proposed pHSA system requires essentially zero energy expenditure to achieve intended environments for capture and regeneration. With 1 kg of adsorbent, pHSA has the ability to capture 1 kg CO2 in less than 4 h of cycling. The tested pHSA adsorbent can also capture more than 96% of total CO2 in a given raw gas stream flowing through the capture chamber. This proof-of-concept study of a pH swing adsorption/biocatalytic adsorbent system suggests the potential to effectively operate under ambient conditions and exhibit advantageous operational efficiencies to other high-profile CO2 capture systems.

AbstractClimate change poses new and unique challenges that threaten lives and livelihoods. Given the increasing risks and looming uncertainty of climate change, increasing attention has been directed towards adaptation, or the strategies that enable humanity to persist and thrive through climate change the best it can. Though climate change is a global problem often discussed at the national scale, urban areas are increasingly seen as having a distinct role, and distinctive motivation and capacity, for adaptation. The 12 articles in this special issue explore ways of understanding and addressing climate change impacts on urban areas. Together they reveal young but rapidly growing scholarship on how to measure, and then overcome, challenges of climate change. Two key themes emerge in this issue: 1) that we must identify and then overcome current barriers to urban adaptation and 2) frameworks/metrics are necessary to identify and track adaptation progress in urban settings. Both of these themes point to the power of indicators and other quantitative information to inform priorities and illuminate the pathway forward for adaptation. As climate change is an entirely new challenge, careful measurement that enables investment by private and public parties is necessary to provide efficient outcomes that benefit the greatest number of people.

Abstract With promising benefits such as traffic emission reduction, traffic congestion alleviation, and parking problem solving, Electric Vehicle (EV)-sharing systems have attracted large attentions in recent years. Different from other business modes, customers in sharing economy systems are usually price sensitive. Therefore, it is possible to shift the usage of shared EVs through a well-designed Dynamic Pricing Scheme (DPS), with the objective of maximizing the system operator's total profit. In this study, we propose a novel DPS for a large-scale EV-sharing network to address the EV unbalancing issue and satisfy the vehicle-grid-integration (VGI) service based on accurate station-level demand prediction. The proposed DPS is formulated as a complex optimization problem, which includes two Price Adjustment Level (PAL) decision variables for every origin-destination pair of stations. The two PALs are employed to affect the EV-sharing demand and travel time between each station pair, respectively. Physical and operational constraints from both EV demand and VGI service aspects are also included in the proposed model. Two case study are conducted to validate the effectiveness of the proposed method.