• Energy Research
• nano-technology close
• 7. Clean energy close
• 11. Sustainability close
• DE close

Abstract With the rapid advancement in wearable electronics, energy harvesting devices based on triboelectric nanogenerators (TENGs) have been intensively investigated for providing sustainable power supply for them. However, the fabrication of wearable TENGs still remains great challenges, such as flexibility, breathability and washability. Here, a route to develop a new kind of woven-structured triboelectric nanogenerator (WS-TENG) with a facile, low-cost, and scalable electrospinning technique is reported. The WS-TENG is fabricated with commercial stainless-steel yarns wrapped by electrospun polyamide 66 nanofiber and poly(vinylidenefluoride-co-trifluoroethylene) nanofiber, respectively. Triggered by diversified friction materials under a working principle of freestanding mode, the open-circuit voltage, short-circuit current and maximum instantaneous power density from the WS-TENG can reach up to 166 V, 8.5 µA and 93 mW/m2, respectively. By virtue of high flexibility, desirable breathability, washability and excellent durability, the fabricated WS-TENG is demonstrated to be a reliable power textile to light up 58 light-emitting diodes (LED) connected serially, charge commercial capacitors and drive portable electronics. A smart glove with stitched WS-TENGs is made to detect finger motion in different circumstances. The work presents a new approach for self-powered textiles with potential applications in biomechanical energy harvesting, wearable electronics and human motion monitoring.

In the search for a nontoxic replacement of the commonly employed CdS buffer layer for Cu(In,Ga)(S,Se) $_\mathrm{2}$ based solar cells, chemically deposited Zn(O,S) thin films are a most promising choice. In this paper, we address the usually slow deposition speed of Zn(O,S) in a newly developed ammonia-free chemical bath process, resulting in a deposition of 30 nm in 3 min with good homogeneity on 30 cm × 30 cm sized substrates. Solar cells with buffer layers prepared from this process match the efficiency of CdS reference cells. In a second step, we address the light-soaking post-treatment, still needed for maximum efficiencies. By addition of aluminum to the deposition process, the initial efficiencies can be increased slightly. With the addition of boron, the light-soaking post-treatment is rendered unnecessary, while maintaining high efficiencies above 15%, surpassing reference cells with CdS buffer.

Photoconductive antennas (PCAs) are among the most conventional devices used for emission as well as detection of terahertz (THz) radiation. However, due to their low optical-to-THz conversion efficiencies, applications of these devices in out-of-laboratory conditions are limited. In this paper, we report several factors of enhancement in THz emission efficiency from conventional PCAs by coating a nano-layer of dielectric (TiO2) on the active area between the electrodes of a semi-insulating GaAs-based device. Extensive experiments were done to show the effect of thicknesses of the TiO2 layer on the THz power enhancement with different applied optical power and bias voltages. Multiphysics simulations were performed to elucidate the underlying physics behind the enhancement of efficiency of the PCA. Additionally, this layer increases the robustness of the electrode gaps of the PCAs with high electrical insulation as well as protect it from external dust particles.

Abstract This paper presents a comparison of commercially used German and Russian reactor pressure vessel steels from the positron annihilation spectroscopy (PAS) point of view, having in mind knowledge obtained also from other techniques from the last decades. The second generations of Russian RPV steels seems to be fully comparable with German steels and their quality enables prolongation of NPP operating lifetime over projected 40 years. The embrittlement of CrMoV steel is very low due to the dynamic recovery of radiation-induced defects at reactor operating temperatures.

Abstract Recently bifacial n-type passivated emitter and rear totally diffused (PERT) monocrystalline silicon solar cells have become one hot spot in photovoltaic (PV) industries, due to good bifaciality, high and stabilised conversion efficiency. Unlike passivated emitter and rear contacts (PERC) structure, n-PERT solar cells require the use of a thin and uniform back surface field (BSF) layer, usually achieved by phosphorus doping. In this study, we optimised the phosphorus diffusion process in terms of surface concentration, junction depth and carrier lifetime. The effects of different phosphorus BSF were investigated by fabricating n-type front and back contact (nFAB) PERT solar cells using industrial feasible approaches and M2 size Czochralski (Cz) monocrystalline Si wafers (6 in., 244.32 cm2). Good phosphorus profiles were developed, which gives low parasitic absorption, low contact resistance and low J0 value when passivated with silicon nitride (SiNx) layer. The optimised champion cell shows a high Voc of 666.5 mV, Jsc of 40.2 mA/cm2, fill factor of 79.9%, efficiency of 21.43% from front side-illumination, together with a good bifaciality factor of 93.0%.

Six corrosion protection systems for offshore wind power constructions have been subjected to offshore conditions on a test site in the North Sea in three different exposure zones, namely splash zone, intermediate zone, and underwater zone. The systems included single- and multiple-layered organic coatings, metal-spray coatings, and duplex coatings. Special testing specimens were designed and manufactured and exposed to an offshore environment for three years in order to characterize particular constructive details for different corrosivity zones. The following target parameters were investigated: intensity of fouling, anti-corrosive effect, coating adhesion, coating integrity, flange corrosion, coating performance over welds, and condition of screw connections. Fouling was an issue in the underwater zone and in the intermediate zone, but it did not affect the coating corrosion protection capacity. It was found that duplex systems, consisting of Zn/Al spray metallization, intermediate particle-reinforced epoxy coating, and polyurethane top layer, provided the highest anti-corrosive effect. Mechanical damage to the coatings initiated coating delamination and substrate corrosion. Effective coating systems should be either very resistant to impact or able to compensate for corrosion of the steel. Flange connections were found to be critical structural parts in the splash zone in terms of corrosion. Notable crevice corrosion was observed at places. Except for one coating system, welds have been protected well. Welds, however, affected the corrosion of the steel inside the uncoated internal sections in the underwater samples. Coating integrity on difficult-to-coat structural parts was satisfactory for all systems.

Lead in perovskite solar cells is a potential environmental and health hazard if it is released from accidentally damaged panels. Now, the encapsulation of perovskite solar cells with self-healing polymers is shown to significantly reduce the risk of lead leakage from hail impact under a variety of weather conditions.

Symmetric flow cell cycling of a soluble phenothiazine.

A novel free-standing and flexible counter electrode for dye solar cells has been developed by conveniently transferring a vertically aligned carbon nanotube forest onto an oxygen-plasma-treated flexible, free-standing and conductive nanocomposite foil. Vertically aligned carbon nanotubes were first grown onto an aluminium foil by chemical vapour deposition and then transferred to the nanocomposite surface by hot pressing. The most meaningful electrochemical parameters have been quantitatively analyzed by means of electrochemical impedance spectroscopy and cyclic voltammetry in order to elucidate how the implementation of the anisotropic carbon nanotube top layer impacts the ultimate catalytic performances of the plate. Such an engineered counter electrode is able to guarantee a fast and effective reduction of the iodide-based electrolyte as well as to provide a solar conversion efficiency that is comparable with a typical Pt/TCO-coated rigid counter electrode. A photocurrent density higher than 13.36 mA cm−2 along with a solar conversion efficiency of 7.26% have been reported for the dye solar cell mounting a counter-electrode based on vertically aligned carbon nanotubes implanted onto a conductive nanocomposite plate.