• Energy Research
• physical sciences close
• 13. Climate action close
• CN close
• GB close
• DE close
• FR close

Correction for ‘Mesoporous thin film WO3 photoanode for photoelectrochemical water splitting: a sol–gel dip coating approach’ by Samantha Hilliard et al., Sustainable Energy Fuels, 2017, 1, 145–153.

AbstractCosmic Ray Albedo Neutron Decay (CRAND) has been recently confirmed as a source of energetic electrons at the inner edge of the inner belt by the Colorado Student Space Weather Experiment (CSSWE) mission. Here we use observations from the Detection of Electro‐Magnetic Emissions Transmitted from Earthquake Regions (DEMETER) mission, to investigate the CRAND contribution to inner belt electrons quantitatively over a broad energy range (~100–800 keV). Spectral fitting analysis supports the conclusion that CRAND is the most important electron source at the inner edge of the inner belt. For the first time, we show that CRAND is the dominant source of >250‐keV quasitrapped electrons throughout the inner belt and slot region during quiet times. We suggest that additional sources for <250‐keV electrons exist, perhaps from inward transport. In contrast, dynamics of electrons in the inner belt and slot region is dominated by injections during active times.

AbstractEnergy is the biggest crisis to humanity in the future. Nowadays, most of the energy used on earth comes from oil, gas and coal. According to the recent exploring and consuming rates, the energy will be exhausted in 50-100 years. Whether we can solve the crisis is closely related to the survival of humanity on the earth. The irradiation from the sun is the biggest energy source. Building PV power plant to utilize the energy from sun will be an only way to sustain the life cycle on the earth. However, the development of PV power plants require the huge supply of PV cell and the fabrication process may bring a quantity of pollution and waste, which is harmful to the environment. On the other hand, super large PV power plant will occupy huge land. If the land cannot be explored and used reasonably, this will not benefit the human life either. In this article, we address the discussions about the above problems and propose the initial suggestions about development trend of PV industry and the safety operation mode of super PV power plant.

AbstractUsing a low supply water temperature in heating conditions and a high water temperature during cooling can increase energy efficiency, use renewable energy sources, and provide a comfortable and healthy indoor climate. High temperature cooling and low temperature heating is achieved by reducing temperature difference in heat trans er and energy transportation process. The losses in temperature difference can be classified into three types: by heat/moisture exchange; by energy transportation through air/water circulation; by indoor terminal that releases heat/cooling to indoor condit oned space. The air handling process of HVAC system and indoor terminals are the key factor of reducing temperature differen e.Aiming at the losses in HVAC system, Annex 59, titled High Temperature Cooling & Low Temperature Heating in Buildings, is a new international cooperative work under the framework of International Energy Agency (IEA) Energy in Buildings and Communities (EBC). This paper introduc s the background, scope, objective, structure and deliverables of Annex 59. Annex 59 will try to present a new perspective and a new concept to analyze HVAC system in buildings. The goal of the Annex is to build up new concept of analyzing HVAC system from the perspective of reducing mixture loss and transfer loss and th n apply it in high temperature cooling and low temperature heating system.

A simple expression for multiple reflections within a collector with a double glazed cover is proposed

Abstract Ventilation systems are of vital importance for buildings, not only to provide acceptable thermal conditions and air quality for occupants, but also with regards to energy usage. Impinging jets can be encountered in many ventilation strategies which have major impacts on the acoustic environment and energy performance. The self-sustaining tones can be generated in such applications where a feedback loop is installed in the system. This phenomenon is explained by the corollary of Howe who shows that the origin of noise in such configurations can be attributed to fluid rotations. Howe highlights the role of phase conditions between the vorticity, the velocity of the flow and the acoustic velocity for the optimization of energy transfers between the turbulent kinetic energy and the sound field. In this work, we use 2D-PIV technique and a microphone respectively to measure the kinematic fields simultaneously with the acoustic generation for a rectangular jet impinging on a slotted plate. This study aims to investigate the transfers between the turbulent kinetic energy and the sound field for two Reynolds numbers presenting a high and a low noise levels. It is shown that phase conditions are necessary for the optimization of energy transfer which allows the installation of the self-sustained loop in the flow. It was found also that the change of the aerodynamic mode which is directly related to the self-sustained frequency amplifies the sound intensity and promotes the transfer of energy to the acoustic field.

Accurate estimation of extreme wave conditions is critical for offshore renewable energy activities and applications. Wave power is the transport of energy by wind waves, and the capture of that energy to do useful work. Wave energy converter (WEC) devices are designed to sustain the wave-induced loads that they experience during both operational and survival sea states. The extreme values of these forces are often a key cost driver for WEC designs. These extreme loads often occur during severe storms; therefore careful examination of harsh wave conditions during the device design process is needed. Consequently the development of a specific extreme condition modeling method is essential. This paper presents a novel method for estimating extreme wave statistics, based on the hourly measured wave height maxima at the location of interest. Wave measurements, analyzed in this paper, were collected at SEM-REV offshore sea station located near the coast of France, during years 2001–2010. Note that applied statistical methodology is general and can be well applied to a measured WEC response, and its technology risk assessment. Accurate estimation of extreme wave conditions is critical for offshore renewable energy activities and applications. SEM-REV is known French wave energy test site. The method, referred to as ACER method, is presented in brief detail. ACER method provides an accurate extreme value prediction, utilizing available data efficiently. In this study the estimated return level values, obtained by ACER method, are compared to the corresponding return level values obtained by Gumbel method. Based on the overall performance of the proposed method, it is concluded that the ACER method can provide a robust and accurate prediction of extreme wave height at a given location.

Diesel engine exhaust pipes are in a high-temperature and high-oxygen environment; the carbon soot formed by fuel combustion will be partially oxidized, and its physicochemical properties will change significantly after oxidation. In order to study the effect law of partial oxidation on carbon soot particles emitted from automobiles, commercial carbon black samples (Printex-U carbon) were selected to replace actual carbon soot particles in this paper, and experiments were conducted on a fixed-bed catalytic oxidation device to obtain carbon soot particles with four oxidation rates by varying the time duration of oxygen introduction. Subsequently, the microstructure images of the corresponding carbon soot particles were obtained using TEM and measured after image processing with ImageJ software. The results showed that the average particle size, particle layer spacing, and distortion of carbon soot particles gradually decreased with the increase in oxidation rate. Moreover, the basic particle edge structure of carbon soot particles gradually blurred, the disordered structure inside the carbon soot particles increased, and the structure was destroyed or oxidized away with the gradual oxidation of the outer layer. Lastly, the density degree inside the particles gradually increased, the outer carbon layer arrangement became more regular, and the graphitization degree gradually became larger. The oxidation of carbon soot particles followed the contraction model and the internal oxidation model.