• Energy Research
• physical sciences close
• 7. Clean energy close
• CN close
• DE close
• GB close
• FR close

Characteristics of Tm:YAG ceramic for high efficient 2-μm lasers are analyzed. Efficient diode end-pumped continuous-wave and Q-switched Tm:YAG ceramic lasers are demonstrated. At the absorbed pump power of 53.2W, the maximum continuous wave (cw) output power of 17.2 W around 2016 nm was obtained with the output transmission of 5%. The optical conversion efficiency is 32.3%, corresponding to a slope efficiency of 36.5%. For Q-switched operation, the shortest width of 69 ns was achieved with the pulse repetition frequency of 500 Hz and single pulse energy of 20.4 mJ, which indicates excellent energy storage capability of the Tm:YAG ceramic.

AbstractThis paper presents an experimental assessment of a blended fatigue‐extreme controller for load control employing trailing edge flaps on a lab‐scale wind turbine. The controller blends between a repetitive model predictive controller that targets fatigue loads and a dedicated extreme load controller, which consists of a simple on‐off load control strategy. The Fatigue controller uses the flapwise blade root bending moments of the three blades as input sensors. The Extreme controller additionally uses on‐blade angle of attack and velocity measurements as well as acceleration measurements to detect extreme events and to allow for a fast reaction. The experiments are conducted on the Berlin Research Turbine within the large wind tunnel of the TU Berlin. In order to reproduce test cases with deterministic extreme wind conditions that follow industry standards, the wind tunnel was redesigned. The analyzed test cases are extreme direction change, extreme coherent gust, extreme operating gust and extreme coherent gust with direction change. The test cases are analyzed by on‐blade angle of attack and velocity measurements. The load control performance of the Blended controller is compared to the pure fatigue oriented and the pure extreme load controller. The Blended controller achieves a maximum flapwise blade root bending moment reduction of 23%, which is comparable to the reduction achieved by the Extreme controller.

In the search for a nontoxic replacement of the commonly employed CdS buffer layer for Cu(In,Ga)(S,Se) $_\mathrm{2}$ based solar cells, chemically deposited Zn(O,S) thin films are a most promising choice. In this paper, we address the usually slow deposition speed of Zn(O,S) in a newly developed ammonia-free chemical bath process, resulting in a deposition of 30 nm in 3 min with good homogeneity on 30 cm × 30 cm sized substrates. Solar cells with buffer layers prepared from this process match the efficiency of CdS reference cells. In a second step, we address the light-soaking post-treatment, still needed for maximum efficiencies. By addition of aluminum to the deposition process, the initial efficiencies can be increased slightly. With the addition of boron, the light-soaking post-treatment is rendered unnecessary, while maintaining high efficiencies above 15%, surpassing reference cells with CdS buffer.

Abstract This paper presents a comparison of commercially used German and Russian reactor pressure vessel steels from the positron annihilation spectroscopy (PAS) point of view, having in mind knowledge obtained also from other techniques from the last decades. The second generations of Russian RPV steels seems to be fully comparable with German steels and their quality enables prolongation of NPP operating lifetime over projected 40 years. The embrittlement of CrMoV steel is very low due to the dynamic recovery of radiation-induced defects at reactor operating temperatures.

Abstract In this work, we propose an acoustic energy harvesting metamaterial consisting of an array of silicone rubber pillars and a PZT patch deposited on an ultrathin aluminum plate with several holes based on locally resonant mechanism. The resonance is formed by removing four pillars, drilling a few of holes and attaching the PZT patch on the aluminum plate. The strain energy originating from an incident acoustic wave is centralized in the resonant region, and the PZT patch is used to convert the elastic strain energy into electrical power. Numerical analysis and experimental results show that the proposed millimeter-scale harvester with holes obviously improves the effect of acoustic energy harvesting while performing at the subwavelength scale for sonic low-frequency environment (less than 1150 Hz). In addition, the experimental results demonstrate that the maximum output voltage and power of the proposed acoustic energy harvesting system with 16 holes of 2 mm radius are 3 and 10 times higher than those without holes at the resonant mode for 2 Pa of incident acoustic pressure. Both the number and size of holes have a significant effect on the performance of acoustic energy harvesting. The advantages of the proposed structure are easy-to-machine and full of practicality, and it can be used in broad applications for low-frequency acoustic energy harvesting.

Abstract As promising candidates for thermophotovoltaic energy conversion systems, epitaxial thin film III–V cells have gained increasing attention due to their potential for reduced weight. However, few studies have been done to date to enhance the performance of epitaxial single crystal GaSb thin film cells. In this work, the internal quantum efficiencies of epitaxial single crystal GaSb thin film cells with Zn-diffused and epitaxial p–n junctions were predicted with models verified using the corresponding experimental results. The results are the first to indicate that, for the former, when the base region thickness is approximately equal to minority carrier diffusion length, the maximal IQE can be obtained and it is notably higher than the IQE of GaSb bulk cell at wavelengths from 800 to 1700 nm. Reducing bottom surface recombination velocity and increasing hole Shockley–Read–Hall lifetime could also increase the IQE. While for the latter, the results demonstrated that the optimal base region thickness is also approximately equal to minority diffusion length, and reducing emitter region thickness will increase the IQE when the base region is optimized. The comparison of the two optimized GaSb thin film cells showed that the GaSb thin film cell with epitaxial p–n junction has a higher IQE.

A new approach for the electromagnetic control and propulsion of a current carrying electric arc plasma ring is described. The essence of the approach is to form and manipulate the arc plasma outside rather than inside a magnetic field producing coil so that pulsed plasma thrusts can be produced in a choice of different directions. The interaction of the electric arc, formed in atmospheric pressure air, with such a magnetic field has been investigated. It has been shown that a stable azimuthal plasma ring can be rapidly produced by the simple process of separating two annular contacts. Pulsed plasma propulsion is obtained when the arc plasma and B-field sustaining current is reduced to zero whereby the constraining electromagnetic forces are removed and, as a consequence, the resulting plasma ring expands radially outwards. Several different measurement techniques have been deployed for investigating the behavior of the plasma ring. These include electrical probing, B-field probing and high-speed plus video photography. The results suggest that the plasma control and propulsion is governed by a combination of effects including ablation of the material around which the plasma ring is formed and self-pressurization related to the device geometry, as well as the electromagnetic forces. Preliminary results indicate that through the use of appropriate device geometries, the arc plasma may be propelled in axially opposite directions as well as radially.

Swirl combustors have proven as effective flame stabilisers over a wide range of operation conditions thanks to the formation of well-known swirl coherent structures. However, employment of swirl combustors to work on lean premixed combustion modes while introducing alternative fuels such as high hydrogen blends result in many combustion instabilities. Under these conditions, flame flashback has been considered as one of the major instability problems that have the potential of causing considerable damages of the combustion systems hardware in addition to the significant increase in pollutant levels. Combustion Induced Vortex Breakdown (CIVB) is considered a very particular mode of flashback mechanism in swirling flows as this type of flashback occurs even when the fresh mixture’s velocity is higher than the flame speed, consequence of the interaction between swirl structures and swirl burner geometries. Improvements of burner geometries and manipulation of swirl flows can produce good resistance against this type of flashback. However, increase flame flashback resistance against CIVB can lead to an increase in the propensity of another flashback mechanism, Boundary Layer Flashback (BLF). Thus this paper presents an experimental and numerical approach that allows the increase in CIVB resistance by using diffusive air injection and simultaneously avoid BLF by changing the wall boundary layer characteristics using microsurface grids as a liner for the nozzle wall. Results show that using those two techniques together has promising potentials regarding wider stable operation for swirl combustors, enabling them to burn a great variety of fuel blends safely.