• Energy Research
• Closed Access close
• Embargo close
• other engineering and technologies close
• IT close
• FR close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

The electrical resistance of Ni 50 Ti 30 Hf 20 and Ni 50 Ti 40.5 Hf 9.5 alloys during Stress Assisted Two Way Memory Effect was investigated with the aim to deduce the relationship between electrical resistance and deformation across the transformation range. Results show an almost linear relationship although a crossing point between increasing and decreasing deformation may compromise the use of these alloys actuators.

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.

Abstract The elemental dissolution of Cu-Zn alloys was investigated as a function of Zn content ranging from 0 to 45 wt%. Atomic emission spectroelectrochemistry (AESEC) was utilized to directly monitor Cu2+ and Zn2+ release and oxide growth as function of time during potentiodynamic experiments. It was determined that Cu dissolution undergoes a simultaneous mechanism of Cu2O formation and Cu2+ release. The addition of Zn in Cu-Zn alloy does not measurably change the dissolution mechanism of Cu2+ and the rate of aqueous Cu2+ was only dependent on the potential. Zn dissolution was however blocked by the formation of a Cu(0) film which shifted the Zn dissolution in the anodic direction.

Abstract Reaching universal access to electricity by 2030 requires a massive deployment of mini-grids in rural areas of developing countries. Among the many challenges hindering this process, there are the high uncertainties in assessing demand patterns in rural communities, the costs of field survey campaigns, and the absence of ample and reliable datasets coming from existing projects. This paper tries to address these issues by presenting and discussing a database of load profiles from sixty-one off-grid mini-grids from developing countries worldwide, gathered from the literature, private developers and fieldworks, and reported with technical, socio-economic and geographical characterization factors. A clustering procedure led to the identification of five archetypal load profile clusters, which are presented and analyzed together with their load duration curves. Subsequently, the distribution among the clusters of the various characterization factors selected is studied. The proposed approach allows to widen the range of load profiles usually considered, and to seek correlations between the load profile shapes, the peak power and average energy consumption per connection, the number of customers, the age of measurement, geographical position, operator model, type of tariff and generation technologies present. This work establishes a first step in the creation of a shared database for load profiles of rural mini-grids, helping to overcome the lack of available data and difficulties of demand assessment, proposing original insights for researchers to understand load patterns, and contributing to reduce risks and uncertainties for mini-grid developers.

This paper presents the direct power control (DPC) of asymmetrical six-phase permanent magnet synchronous generator (A6PMSG) which supplied the isolated load via two PWM rectifiers. The study concerns the method of control by the converter (DPC). The proposed method is around two hysteresis controllers that enable the adjustment of active and reactive power. The research in this paper is verified by MATLAB SIMULINK software. It has been demonstrated through the simulation results that the proposed strategy can be an attractive and practical solution to multi-phase machines applications.

Abstract The hybrid pneumatic power system (HPPS) proposed in this research replaces the battery’s electric-chemical energy with flow work and optimizes the management and utilization of the energy. This power system is able to keep the internal-combustion engine working at its optimal condition and turn its waste energy into effective mechanical energy and so enhance the thermal efficiency of the whole system. Using computer simulation software ITI-SIM, this study simulates the overall dynamic characteristics of the system in accordance with the regulated running-vehicle test-mode ECE47, and, with experimental verification and analysis, proves that this system can meet the requirements of the standard running-car mode. As for recycling the waste energy, the experimental results show that this design could offset the shortcomings of the low-density of pneumatic power and so effectively enhance the efficiency of the whole system.

In this paper, we present the conjugate heat transfer analysis in a 167-kVA dry-type transformer using the parallel version of the computational fluid dynamics code Fluent 6.0. The renormalization group kappa-epsiv model is proposed to compute the turbulent aspect of the convective airflow inside the transformer metal tank for Air Natural/Air Natural cooling conditions. An experimental approach was used to assess Joule losses in the low-/high-voltage windings and eddy-current losses in the magnetic core. The resulting mathematical model was solved using 14 compute nodes on a distributed machine.

Abstract Italy reformed its water and sanitation services in 1994. The strategy aimed at transforming public entities, financed by the central budget, into self-sufficient professional companies regulated at arms' length. Nearly 20 years after, the reform has failed to deliver (despite some partial success). Italians have been divided in two parties: those blaming public sector inefficiencies and calling for competitive tendering; and those refusing to privatize water and willing to go back to the fiscal budget. In this article, we suggest that both parties are wrong. Underperformance is not related to the ownership structure of water companies, but rather to poor regulatory design and lack of understanding of the regulatory requirements that are implicit in the management model chosen, namely the concession contract.