• Energy Research
• 13. Climate action close
• 15. Life on land close
• GB close
• IN close
• SA close

With the 2015 Paris Agreement pursuing efforts to limit global temperature increase to below 2°C above pre-industrial levels and the “energy trilemma” goals of energy security, energy equity and environmental sustainability, decarbonisation remains a priority across all of the United Kingdom (United Kingdom) energy system, not just electricity. Electricity and thermal energy storage technologies can offer a host of benefits across the energy value chain through the abilityS to capture, store and then release electricity or thermal energy over a period of time. These benefits include helping capture the full potential of renewable generation and providing services such as frequency response and reserve to Great Britain’s (GB) electricity system. In addition, with the aforementioned climate targets in mind, energy storage can also play a role in facilitating the decarbonisation of other activities and sectors. Here we delve deeper into how energy storage technologies can contribute to both energy sector transformation and more broadly, decarbonisation. Furthermore, we discuss the importance of ensuring a technology-agnostic approach to the development of policy and regulation with relevance to energy storage. This ensures that storage technologies with significant potential to contribute to the ‘energy trilemma’ goals are not precluded from entering the market due to unfavourable policy and regulatory frameworks.

Abstract The consumption of takeaway food is increasing worldwide. Single-use containers used for takeaway food represent a significant source of waste and environmental impacts due to their low recyclability. Consequently, it is important to identify the best available alternatives and improvement opportunities to reduce the environmental impacts of fast-food containers. For these purposes, this study estimates and compares for the first time the life cycle impacts of three most widely-used types of takeaway container: aluminium, polypropylene and extruded polystyrene. These are also compared to reusable polypropylene containers. The findings suggest that single-use polypropylene containers are the worst option for seven out of 12 impacts considered, including global warming potential. They are followed by the aluminium alternative with five highest impacts, including depletion of ozone layer and human toxicity. Overall, extruded polystyrene containers have the lowest impacts due to the lower material and electricity requirements in their manufacture. They are also the best option when compared to reused takeaway polypropylene containers, unless the latter are reused 3–39 times. The number of uses needed for the reusable “Tupperware” polypropylene food savers is even higher, ranging from 16 to 208 times, with terrestrial ecotoxicity being always higher than for extruded polystyrene, regardless of the number of uses. However, extruded polystyrene containers are currently not recycled and cannot be considered a sustainable option. If they were recycled in accordance with the European Union 2025 policy on waste packaging, most of their impacts would be reduced by >18%, while also reducing littering and negative effects on marine organisms. Most of the impacts of the other two types of container would also be reduced (>20%) through increased recycling. Implementing the European Union 2025 policy on recycling of waste packaging would reduce all the impacts by 2%–60%, including a 33% reduction in global warming potential. Based on 2025 million takeaway containers used annually in the European Union, the latter would save 61,700 t CO2 eq./yr, equivalent to the emissions of 55,000 light-duty vehicles. The outcomes of this study will be of interest to packaging manufacturers, food outlets, policy makers and consumers.

The successful electricity grid integration of solar energy into day-ahead markets requires at least hourly resolved 48 h forecasts. Technologies as photovoltaics and non-concentrating solar thermal technologies make use of global horizontal irradiance (GHI) forecasts, while all concentrating technologies both from the photovoltaic and the thermal sector require direct normal irradiances (DNI). The European Centre for Medium-Range Weather Forecasts (ECMWF) has recently changed towards providing direct as well as global irradiances. Additionally, the MACC (Monitoring Atmospheric Composition & Climate) near-real time services provide daily analysis and forecasts of aerosol properties in preparation of the upcoming European Copernicus programme. The operational ECMWF/IFS (Integrated Forecast System) forecast system will in the medium term profit from the Copernicus service aerosol forecasts. Therefore, within the MACC‑II project specific experiment runs were performed allowing for the assessment of the performance gain of these potential future capabilities. Also the potential impact of providing forecasts with hourly output resolution compared to three-hourly resolved forecasts is investigated. The inclusion of the new aerosol climatology in October 2003 improved both the GHI and DNI forecasts remarkably, while the change towards a new radiation scheme in 2007 only had minor and partly even unfavourable impacts on the performance indicators. For GHI, larger RMSE (root mean square error) values are found for broken/overcast conditions than for scattered cloud fields. For DNI, the findings are opposite with larger RMSE values for scattered clouds compared to overcast/broken cloud situations. The introduction of direct irradiances as an output parameter in the operational IFS version has not resulted in a general performance improvement with respect to biases and RMSE compared to the widely used Skartveit et al. (1998) global to direct irradiance conversion scheme. Cloudy situations and especially thin ice cloud cases are forecasted much better with respect to biases and RMSE, but large biases are introduced in clear sky cases. When applying the MACC aerosol scheme to include aerosol direct effects, an improvement especially in DNI biases is found for cloud free cases as expected. However, a performance decrease is found for water cloud cases. It is assumed that this is caused by the lack of an explicit modelling of cloud-aerosol interactions, while other meteorological forcings for cloud processes like the temperature field are modified by the aerosols.

Yard waste is either dumped or is being openly burned to get rid of it, instead of using it as a valuable renewable energy source. In this study, hydrothermal carbonization of yard waste was conducted to valorize it as a solid bio fuel, using a batch reactor. The effect of process parameter on yield, energy and physicochemical properties of the valorized solid bio fuel (hydrochar) was examined in this study by varying reaction temperature (160-200 °C for 2 h) and reaction time (2-24 h at 200 °C). The calorific value of hydrochar was within a range of 17.72-24.59 MJ/kg as compared to 15.37 MJ/kg for untreated yard waste. Hydrochar mass yield decreased from 78.6% at operating temperature - time of 160 °C -2 h to 45.6% at 200 °C -24 h. The plot of atomic ratios (H/C and O/C) demonstrates improvement in the coalification process which was mainly governed by decarboxylation and dehydration reactions. The grindability of the prepared hydrochar was comparable to that of coal. Hydrochar produced at lower reaction condition (160-200 °C at 2 h) have better flowability as compared to that produced at higher reaction condition (4-24 h at 200 °C). The reaction time longer than 12 h has a minimal effect on the yield, energy and physicochemical properties of hydrochar. Increasing reaction time and temperature improved the ignition and burnt temperature of hydrochar. All reaction condition has an energy ratio (energy output to energy input) of more than one making HTC process a net energy producer.

Abstract The use of water production as a pressure mitigation tool in the context of CO2 storage is widely studied but the impact it might have on the migration behaviour of a buoyant CO2 plume is less well reported. To investigate this further two different scenarios were modelled. In the first, a single water production well was used to draw CO2 along the strike of an open aquifer with a regional dip. Large rates of water production (5–10 times the volume of injected CO2) were required to achieve only small displacements of the CO2 plume. The second scenario investigated to what extent an induced hydraulic gradient might spill CO2 already stored in a structural trap. Here the effects were more pronounced with over 90% of the CO2 being spilled at a water cycling rate of 10 Mt per year (corresponding to a hydraulic gradient of 1.28 bar/km). The modelling was tested by the real case at Sleipner where CO2 migration in the Utsira Sand is potentially impacted by water production at the nearby Volve field. Simulations concluded that the CO2 plume at Sleipner should not be materially affected by water production from Volve and this is supported by the time-lapse seismics.

Daily rainfall is measured as the total (mm) over the 24-hour period 0900 to 0900 GMT. It includes all precipitation - snow, rain, mist and fog. Rainfall was first recorded at Rothamsted in March 1853, using a copper funnel rain gauge (5 inch / 12.7 cm diameter) and measured using a graduated cylinder. Since 2004 it has been measured using an electronic tipping bucket rain gauge (10 inch / 25.4cm diameter), ARG100, calibrated to tip at 0.2mm (which has since become the minimum amount of rain that can be recorded). The rain gauge is placed within a 30cm deep 1.5m radius turf wall, retained by brick, to reduce wind eddies that may potentially blow rain out of the gauges. Data were collected daily manually until 2004 and since then by Automatic Weather Station using a standard protocol. There are differences in the capture rate between the two gauges, see Rainfall for further information. The monthly summary data contained in this spreadsheet are derived from daily data measured at Rothamsted Meteorological Station, Harpenden. Total monthly data is determined from daily data using Genstat 19th Edition. Verification includes checks for instrument errors, for missing data and outliers. The original raw daily data is available, after registering, from the e-RA database. Please contact the e-RA Curators for an access password and further details. This dataset represents the mean monthly rainfall recorded at Rothamsted from October 1985 - September 2017 and is derived from continuous daily records measured at the site. Location: Rothamsted Meteorological Station, Harpenden, Hertfordshire, England 51.82 N 0.37 W 128 m asl.

Data was either measured in situ in the field (N2O flux, soil moisture, rainfall and air temperature) or samples were taken, processed, and analysed in the laboratory (soil pH, electrical conductivity (EC), ammonium, nitrate, microbial community composition and crop yield). N2O flux data was measured on a mobile gas chromatograph (GC) system and integrated to obtain peak areas on Peak490Win10Canabis programme. The times, peak areas and sample ID were then exported into a .CHR file and imported into Flux.NET.3.3 which calculated N2O flux as an output in Excel which was exported as .csv file for deposit in EIDC. N2O flux was used to calculate cumulative N2O flux using trapezoidal integration in Excel and saved in a separate .csv file for deposit in EIDC. Soil moisture was measured on Accilmas with data stored as a .csv on a DataSnap that was downloaded and sorted by treatment and saved as a .csv file. Rainfall and air temperature were downloaded from the weather station as .csv file. Soil pH and EC were recorded manually into a notebook and input into an Excel spreadsheet and exported as a .csv file. Soil ammonium and nitrate content was measured using the microplate method using a programme called Gen5. Date was exported into an Excel spreadsheet and absorbance units used to calculate ammonium/nitrate content in milligrams per kilogram using a calibration curve from a set of standards in an Excel spreadsheet. This was exported as a .csv file. Crop growth data was recorded in the field in a notebook and input into an Excel spreadsheet and exported as a .csv file. Crop yield was recorded in a notebook and input into an Excel spreadsheet and exported as a .csv file. Microbial community composition was measured using 16S gene sequencing on an Illumina MiSeq. This generated raw sequencing reads which were processed using Python and filtered using QIIME v1.3.1. creating asv.count.table.csv of counts of each Amplicon Sequence Variants (ASVs) per sample and taxa.table.csv of the taxonomic lineage for each ASVs. This dataset contains field data on nitrous oxide (N2O) emissions, microbial community composition, crop yield and growth and soil biochemical properties. The field trial consisted of three different treatments of control, conventional microplastic addition and biodegradable microplastic addition where winter barley was grown. The data presented are from field and laboratory measurements. Data was collected by the data authors. The field trial was carried out from September 2020 to July 2021 at Henfaes Field Centre, UK. Research was funded through NERC Grant NE/V005871/1. Do agricultural microplastics undermine food security and sustainable development in developing countries?

SummaryThe adaptation of extra short duration (ESD) pigeonpea (Cajanus cajan) genotypes to rainfed environments was studied on Alfisols and Vertisols at the ICRISAT Center between 1987 and 1989. Despite a slightly shorter crop duration, the grain yield of ESD genotypes was twice as large on Alfisols as on Vertisols. On both soil types, the rate of growth and grain yield were better in crops sown on time than in those where sowing was delayed. The population levels necessary to maximize yield varied among genotypes on Alfisols, where the grain yield of several ESD genotypes compared favourably with that of ICPL 87, a standard short duration genotype. However, none of the ESD genotypes yielded more than ICPL 87 on the Vertisols.

Biogas is a viable alternative for supplying clean and sustainable energy. Despite all manner of policy measures introduced by the Government of India, biogas is not widely used in India. This article tries to identify factors that influence the decision to adopt biogas at household level. We examine a conceptual framework empirically in which a household wants to maximize utility from biogas by using the India Human Development Survey (IHDS) I, which is a nationally representative, multi-topic survey. By applying both maximum likelihood and penalized likelihood methods (Firthlogit) of logistic regression on a sample size of almost 10,384 households, it has been found that wealthy people are more likely to adopt biogas compared to the marginalized section of the society. We recommend more inclusive policy measures for the weaker section of the society to create an enabling environment to make it a self-promoting technology.

Driven by the need to develop a wide variety of products with low environmental impact, biorefineries need to emerge as highly integrated facilities. This becomes effective when overall mass and energy integration through a centralised utility system design is undertaken. An approach combining process integration, energy and greenhouse gas (GHG) emission analyses is shown in this paper for Jatropha biorefinery design, primarily producing biodiesel using oil-based heterogeneously catalysed transesterification or green diesel using hydrotreatment. These processes are coupled with gasification of husk to produce syngas. Syngas is converted into end products, heat, power and methanol in the biodiesel case or hydrogen in the green diesel case. Anaerobic digestion of Jatropha by-products such as fruit shell, cake and/or glycerol has been considered to produce biogas for power generation. Combustion of fruit shell and cake is considered to provide heat. Heat recovery within biodiesel or green diesel production and the design of the utility (heat and power) system are also shown. The biorefinery systems wherein cake supplies heat for oil extraction and seed drying while fruit shells and glycerol provide power generation via anaerobic digestion into biogas achieve energy efficiency of 53 % in the biodiesel system and 57 % in the green diesel system. These values are based on high heating values (HHV) of Jatropha feedstocks, HHV of the corresponding products and excess power generated. Results showed that both systems exhibit an energy yield per unit of land of 83 GJ ha−1. The global warming potential from GHG emissions of the net energy produced (i.e. after covering energy requirements by the biorefinery systems) was 29 g CO2-eq MJ−1, before accounting credits from displacement of fossil-based energy by bioenergy exported from the biorefineries. Using a systematic integration approach for utilisation of whole Jatropha fruit, it is shown that global warming potential and fossil primary energy use can be reduced significantly if the integrated process schemes combined with optimised cultivation and process parameters are adopted in Jatropha-based biorefineries.