• Energy Research
• 7. Clean energy close
• IN close
• SA close
• BE close
• CM close

Abstract The reverse flat-plate collector is a non-concentrating collector. It can collect solar heat at high temperatures which cannot be achieved by conventional non-concentrating collectors. In this paper, the authors have proposed a number of modified versions of the originally proposed reverse flat-plate collector. The new designs are of single, as well as double, absorber type. The thermal performance of these modified reverse flat-plate collectors is compared with that of a single absorber reverse flat-plate collector, as well as with the corresponding normal flat-plate collector. It is found that the new design having two absorbers gives the best thermal performance as compared with other configurations. The analytical models presented in this paper very well describe the experimental results.

Drying experiments have been performed with potato cylinders and slices using a laboratory scale designed natural convection mixed-mode solar dryer. The drying data were fitted to eight different mathematical models to predict the drying kinetics, and the validity of these models were evaluated statistically through coefficient of determination (R(2)), root mean square error (RMSE) and reduced chi-square (χ (2)). The present investigation showed that amongst all the mathematical models studied, the Modified Page model was in good agreement with the experimental drying data for both potato cylinders and slices. A mathematical framework has been proposed to estimate the performance of the food dryer in terms of net CO2 emissions mitigation potential along with unit cost of CO2 mitigation arising because of replacement of different fossil fuels by renewable solar energy. For each fossil fuel replaced, the gross annual amount of CO2 as well as net amount of annual CO2 emissions mitigation potential considering CO2 emissions embodied in the manufacture of mixed-mode solar dryer has been estimated. The CO2 mitigation potential and amount of fossil fuels saved while drying potato samples were found to be the maximum for coal followed by light diesel oil and natural gas. It was inferred from the present study that by the year 2020, 23 % of CO2 emissions can be mitigated by the use of mixed-mode solar dryer for drying of agricultural products.

Abstract In this work addition of ethanol to high viscosity jatropha methyl ester (JME) through port injection is investigated in order to determine its effect fuel viscosity reduction on diesel engine performance. In addition to viscosity alteration, the impact of ethanol addition on combustion characteristics such as combustion duration, ignition delay and emissions levels from diesel engines fuelled with blends of ethanol, diesel and JME is studied in particular. It is found that blending of oxygenated fuels with diesel modifies the chemical structure and physical properties which again alter the engine operating conditions, combustion parameters and emissions levels. However, the injection of only 5% ethanol through port injection allows for a total of 25% blending of biofuels into diesel yet keeping the fuel characteristics close to that of conventional diesel. However, both experimental and numerical results show that ethanol addition in JME blended diesel results in a slight increase in fuel consumption and thermal efficiency for the same power outputs as that of conventional diesel fuel. Also, the combustion characteristics with ethanol addition include improved maximum in-cylinder peak pressure, cumulative heat release (CHR) rate of heat release (ROHR), in-cylinder peak temperature and combustion duration. Regarding emission characteristics the experimental results show significant reduction in smoke, carbon monoxide (CO) and total hydrocarbon (THC) emissions with extended oxygen mass percentage in the fuel at higher engine loads. However, oxides of nitrogen (NOx) emissions are found to increase at high loads although the common tradeoff between smoke and NOx is found to be more prominent for the oxygenated fuels.

AbstractPreparation of uniform, spherical Li4Ti5O12 with high tap density is significant to achieve a high volumetric energy density in lithium‐ion batteries. Herein, Li4Ti5O12 microspheres with variable tap density and tunable size distribution were synthesized by a newly designed industrial spray‐drying approach. The slurry concentration, sintering time, sintering conditions after spraying, and the effect of lithium/titanium molar ratio on the lithium‐ion (Li+) storage capability were investigated. A narrow particle size distribution of around 10 μm and a high tap density close to 1.4 g cm−3 of the Li4Ti5O12 spheres can be obtained under the optimized conditions. The Li4Ti5O12 spheres can deliver a much higher capacity of 168 mAh g−1 at a rate of 1 C and show a high capacity retention of 97.7 % over 400 cycles. The synthetic conditions are confirmed to be critical for improving the electron conductivity and Li+ diffusivity by adjusting the crystal and spatial structures. As‐prepared high‐performance Li4Ti5O12 is an ideal electrode for lithium‐ion batteries or capacitors; meanwhile, the presented approach is also applicable for preparing other kind of spherical materials.

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

Abstract The main hindrances to the large-scale development of renewable-energy projects are the lack of bankability and the inability to align investments and investors with suitable financial instruments or robust policy measures. To illustrate a bankable project, this paper presents a research-based case study on the installation of solar photovoltaic panels on the rooftops of 195 trains of the Indian Railways. Detailed information on the annual running hours, exposure to sunlight, efficiency of solar photovoltaic generation and electrical power demands of each rail coach is considered to conduct a quantitative measure of the tentative amount of fossil fuel savings. The purpose is to provide insight into the types of renewable-energy projects that can be highly attractive to financial institutions and promoters due to their lucrative internal return on investment. As seen in this case study, there are annual savings in diesel of 12 323 088 litres and a CO2 reduction of 32 755 tonnes, with return on investment of 1.3 years. Furthermore, this study conducts a comprehensive analysis of the limitations of existing renewable-energy project financing mechanisms in India. Subsequently, three policy measures are recommended to develop a robust financial mechanism that can effectively meet the needs of investors and investors. These measures include increasing equity injection through a buy-and-hold strategy, providing direct tax benefits to promoters and financing through real-estate investment trusts. The findings are highly relevant to address the challenges associated with bridging the financial gap between access to finance and capital investment in the renewable-energy sector, especially for Asian countries.

Abstract Flow-accelerated corrosion (FAC) is a degradation mechanism that affects carbon steel piping in power plants. The failures and degradation due to FAC have necessitated numerous replacements in many power plants. Several computer codes around the world were developed as part of a systematic program or process to control FAC in power plant utilities. The typical plant model requires the input of the flow parameters, piping configuration and the plant water chemistry. The results on FAC rate are considered the key to proper selection of components for inspection. The lack of information on the effect of the upstream components located in the proximity limited the accuracy of the FAC prediction tools and hence will affect the accuracy in identifying potential inspection locations. In the present study 211 inspection data for 90° carbon steel elbows from several nuclear power plants were used to determine the effect of the proximity between two components on the FAC wear rate. The effect of the velocity as well as the distance between the elbows and the upstream components is discussed in the present analysis. Based on the analyzed trends obtained from the inspection data, significant increase in the wear rate of approximately 70% on average is identified to be due to the proximity.

Abstract This paper aims to present a feasibility study of the innovative plant for methanol synthesis from carbon dioxide-sequestered by fossil fuel power plant and hydrogen, which is produced by water electrolyzer employing the over-production on the electrical grid. The thermo-economic analysis is performed in the framework of the MefCO2 H2020 EU project and it is referred to the German economic scenario, properly taking into account the real market costs and cost functions for different components of the plant. Three different plant capacities for methanol production (4000 10,000 and 50,000 ton/year) have been investigated, assuming an average cost for electrical energy to feed electrolysers and analyzing the influence of the most significant parameters (oxygen selling option, methanol selling price and electrolysers’ capital cost) on the profitability of the plant. The analysis has been performed in W-ECoMP, software for the thermo-economic analysis and plant optimization developed by the University of Genoa.

In response to the pressing need for transportation decarbonization, this paper examines the often overlooked domain of inland waterway transport and seeks to answer which alternative fuel or power source is the most promising for that sector. As the shipping industry significantly contributes to global carbon emissions, it has been shifting towards alternative fuels and decarbonization measures in the effort to reduce them, whereas the inland waterways, operating predominantly on diesel engines, have not achieved equivalent substantial progress. Employing a systematic literature review and regional analysis, this study identifies notable trends. LNG initially emerged as a favored alternative fuel, but recent studies emphasize a shift towards “greener” solutions like batteries and hydrogen. Europe and Asia lead in these developments. This investigation uncovers critical gaps in research and development, particularly in the Northern European countries that have extensive inland waterway networks. It also calls for future studies to explore the performance of vessels that have adopted LNG compared to other emerging alternatives and emphasizes the importance of considering the time lag between technology development and research publication.