• Energy Research
• other engineering and technologies close
• DE close
• IT close
• ES close
• EU close

Editorial Complex Optimization and Simulation in Power Systems

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

Particle receivers are gaining importance in the field of Concentrating Solar Power (CSP) due to the high temperature that particles can achieve without degradation. Several researchers are studying the potential of this technology by means of system analyses, which need simple and light models of the system. This study presents two simple models for the particle receiver. The simplest model is a correlation obtained by fitting the results calculated with a more complex receiver model simulated in CFD. The other model is a 1D model, which is benchmarked against the same CFD results. Although both models achieve high coefficient of determination, R2, when compared to CFD results, the 1D model seems to provide more accurate results (especially during sunsets and sunrises). Both models are integrated into a tecno-economic model developed in previous work. The LCOE obtained with the 1D model is between 7% and 10% greater than the one obtained with the correlation.

Abstract Secondary concentrators are used in solar concentrating systems to redirect solar beams reflected by the primary concentrators to the focal point or line. These components allow to increase the concentrated solar flux density and hence to lower thermal radiation losses. Solar reflectors for secondary concentrators are permanently exposed to environmental conditions, high radiation fluxes and elevated temperatures that potentially cause stress and degradation throughout the time. Therefore, analyzing solar reflectors of secondary concentrators by simulating these conditions is crucial. No previous research works about the durability of solar reflector materials for secondary concentrators have been reported. The present work is focused on studying the degradation of the reflector materials by simulating accelerated aging, caused by several ambient parameters and the effect of concentrated radiation. Both cooled and uncooled systems for secondary concentrators are included in this study. According to results obtained, aluminum reflectors and thin silvered-glass reflectors glued to an aluminum structure showed minimum reflectance losses and structural degradation under the operation conditions of cooled 3D secondary concentrators (tower systems). Following critical aspects to avoid reflector degradation were identified: to select a suitable adhesive material to glue the thin silvered-glass reflector to the support aluminum structure, to properly protect reflectors edges, to design a suitable cooling system and to avoid the combination of high radiation fluxes with mechanical stress. In addition, laminated silvered-glass reflectors have shown to be suitable for uncooled 2D secondary concentrators (Fresnel collectors). Furthermore, a comparison with naturally aged secondary concentrators using silvered-glass reflectors glued to an aluminum structure revealed that the simulated degradation under accelerated conditions performed in this work did reproduce the most frequent degradation patterns suffered in real operating conditions.

This paper introduces a model predictive control (MPC) strategy for the purpose of fuel-optimal operation of a range-extender hybrid vehicle. The modern navigation system nowadays can provide abundant road information. Using this information, the proposed controller solves a global optimization problem offline in order to determine a preset trajectory of the state of charge (SoC). The online MPC uses the resulting SoC trajectory as set-points for the terminal state in every moving horizon. Repeating this process, the optimal energy management along the trip to be traveled can thus be calculated. This proposed control strategy is implemented in the commercial vehicle simulation environment IPG CarMaker. From the first simulation results, the proposed strategy shows a promising fuel saving potential with real-time capability.

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

AbstractIn this paper a complete vehicle system simulation tool chain which applies a Multi Objective Optimization (MOO) methodology for designing the Electric Powertrain (ePT) of Battery Electric Vehicles (BEV) is presented. Optimization scope includes all relevant electric powertrain components from battery, inverter, electric machine to gear box. In addition to cost, vehicle dynamics, energy consumption and range are further optimization targets. For an overall minimal system cost design a multiplicity of interactions between all powertrain components has to be taken into account. High system complexity prevents an expert to consider all relevant correlations without the support of numeric simulation tools. The presented simulation tool chain enables fast identification of the best cost/benefit trade off regarding system cost while considering all defined system performance requirements. The approach enables experts to find unconventional solutions which would have been overlooked applying a classical straight forward approach and, thus, helps to sharpen the expert's knowledge in cause-effect relationships on the system level. Typical use cases are given and illustrated by several practical examples.

The electrical resistance of Ni 50 Ti 30 Hf 20 and Ni 50 Ti 40.5 Hf 9.5 alloys during Stress Assisted Two Way Memory Effect was investigated with the aim to deduce the relationship between electrical resistance and deformation across the transformation range. Results show an almost linear relationship although a crossing point between increasing and decreasing deformation may compromise the use of these alloys actuators.