• Energy Research
• Open Access close
• Embargo close
• other engineering and technologies close
• IT close

Editorial Complex Optimization and Simulation in Power Systems

Laboratory corrosion and scaling testing of metallic materials exposed in high temperature and pressure environments generally involves complex, multi-instrument measurement setups. Here, we present a setup including an autoclave that is instrumented for in-situ electrochemical testing and that contains a ZrO2-based solid-state pH electrode and devices for temperature control and solution stirring. We show results highlighting the importance of adequate pre-calibration of the pH measurement, due to the hysteresis depending on temperature sweep. Additionally, we illustrate how interfacing the autoclave and the electrochemical cell to measuring and controlling instruments, using different data communication interfaces, can create ground loops. These ground loop interferences can introduce significant errors in the measurement, such as a potential shift of >100 mV. In complex, multi-instrument setups, a complete understanding of ground loops may often be difficult. Thus, we recommend systematic checks to identify the ground loops and we propose measures to avoid them. Measurement, 155 ISSN:0263-2241 ISSN:1873-412X

UV/visible light is a promising radiation source for biomass pretreatment, but very little knowledge is available on the effect of UV on the thermal behavior of lignocellulose in comparison with more classical, physical pretreatment methods. In this paper, we investigate the effects of ball-milling and UV irradiation on two species of softwood and two species of hardwood, using X-ray diffractometry (XRD), evolved gas analysis-mass spectrometry (EGA-MS), and pyrolysis-gas chromatography coupled to mass spectrometry (Py-GC/MS). The XRD data showed that the crystalline fraction of cellulose was destroyed by milling, but not by irradiation. The EGA-MS data and isoconversional kinetic analysis showed that both milling and irradiation can reduce the thermal stability of wood up to a limit value. The Py-GC/MS data showed that irradiation caused the most significant changes in the pyrolytic behavior of the wood species, increasing the ratio of holocellulose to lignin pyrolysis products and the reactivity of cellulose toward the derivatizing agent. Softwoods were more affected by irradiation than hardwoods. This paper shows that UV irradiation can decrease the recalcitrance of biomass toward pyrolysis, but its efficiency is highly dependent on the type of lignocellulosic substrate.

Research on corona discharge, shared by physics, chemistry and electrical engineering, has not arrested yet. As a dissipative process, the development of corona increases the resistive losses of transmission lines and enhances the line capacitance locally. Introducing additional losses and propagation delay, along the line, non-linearity and non-uniformity of the line parameters; therefore, corona should not be neglected. The present work is meant to provide the reader with comprehensive information on the corona macroscopic phenomenology and development, referring to the most relevant contributions in the literature on this subject. The models proposed in the literature for the simulation of the corona development are reviewed in detail, and sensitivity curves are provided to highlight their dependence on the input parameters.

The subject of the research is oriented to typical buildings, often critical from the energy standpoint, which are represented by social housings. The refurbishment target should be the NZEB model, even if it is very difficult to find suitable general solutions. As the renovation design process depends also on the sustainability of costs, an evaluation procedure, previously proposed, is widened to take into account this aspect, by considering characteristics and constraints, and assuring reasonable costs for the most suitable solutions. The methodology has been applied to a case study represented by a common building unit. The insulation improvement is made through a choice of the most suitable combination of material and thickness, with the aim not only of the energy saving, but also of the reduction of the risk of vapour condensation that depends, among other things, on the position of the insulating materials within the wall’s structure. Some combined refurbishment solutions for the building envelope are examined and the corresponding costs are evaluated. Moreover, to show the importance of the problem in mild and continental climates, a comparison of the results in different climatic conditions is presented.

The recent advancements in Artificial Intelligence have paved the way for remarkable achievements in tasks that have traditionally posed challenges even for humans [...]

Abstract This paper presents a non-stoichiometric equilibrium model for the simulation of biomass downdraft gasifiers. The chemical equilibrium is determined by minimizing the Gibbs free energy. Five elements characterize the biomass and 15 chemical species are considered in the syngas. The model calculates the lower heating value of the syngas and the relative abundances of gasification products. An advantage of this model is that it can easily calculate not only the concentrations of the main gasification products, but also the concentrations of minor product, especially the pollutant chemical species containing Nitrogen and Sulfur. To analyse the model behaviour, a sensitivity analysis on process parameters is presented. The model is validated by comparing its results with the results of simulation carried out with a stoichiometric model and with experimental data found in literature. Finally, the model is applied to the study of the gasification of forest waste.