• Energy Research
• physical sciences close
• 7. Clean energy close
• 13. Climate action close
• 6. Clean water close
• 14. Life underwater close

AbstractHeterojunction CdS/CdTe thin film solar cells were fabricated with a superstrate structure consisting of the successive layers: soda lime glass/ITO/CdS/CdTe/back contact. ZnTe:Cu films were deposited on the back surface of the CdTe layer presenting as ohmic back contact. The substrate was soda lime glass coated with ITO films by rf magnetron sputtering serving as the transparent front contact. A thin layer of CdS with thickness about 80nm was applied by chemical bath deposition. Close-spaced sublimation of the CdTe films was accomplished by placing a CdTe source in a close proximity (6mm) to the substrate in vacuum chamber with low pressure about 3×10-2 mbar. The source was heated to 550 ∘C and the substrate to 450 ∘C. This arrangement causes Cd and Te to sublime from source and diffuse to the substrate. The fabricated cells were investigated using current-voltage (I-V) in the temperature range 20-300K under a standard AM1.5 illumination in order to define the transport mechanism in the heterojunction. Tunnelling enhanced interface recombination has been found to dominate carrier transport mechanism in the junction at all investigated temperatures.

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

Characteristics of Tm:YAG ceramic for high efficient 2-μm lasers are analyzed. Efficient diode end-pumped continuous-wave and Q-switched Tm:YAG ceramic lasers are demonstrated. At the absorbed pump power of 53.2W, the maximum continuous wave (cw) output power of 17.2 W around 2016 nm was obtained with the output transmission of 5%. The optical conversion efficiency is 32.3%, corresponding to a slope efficiency of 36.5%. For Q-switched operation, the shortest width of 69 ns was achieved with the pulse repetition frequency of 500 Hz and single pulse energy of 20.4 mJ, which indicates excellent energy storage capability of the Tm:YAG ceramic.

We investigate the effect of slowly-varying parameter on the energy transfer in a system of weakly coupled nonlinear oscillators, with special attention to a mathematical analogy between the classical energy transfer and quantum transitions. For definiteness, we consider a system of two weakly coupled oscillators with cubic nonlinearity, in which the oscillator with constant parameters is excited by an initial impulse, while a coupled oscillator with slowly-varying parameters is initially at rest. It is proved that the equations of the slow passage through resonance in this system are identical to equations of the nonlinear Landau-Zener (LZ) tunneling. Three types of dynamical behavior are distinguished, namely, quasi-linear, moderately nonlinear and strongly nonlinear. The quasi-linear systems exhibit a gradual energy transfer from the excited to the attached oscillator, while the moderately nonlinear systems are characterized by an abrupt transition from the energy localization on the excited oscillator to the localization on the attached oscillator. In the strongly nonlinear systems, the transition from the energy localization to strong energy exchange between the oscillators is revealed. A special case of the rapid irreversible energy transfer in the strongly nonlinear system with slowly-varying parameters is also investigated. The conditions providing different types of the dynamical behavior are derived. Explicit approximate solutions describing the transient processes in moderately and strongly nonlinear systems are suggested. Correctness of the constructed approximations is confirmed by numerical results.

Co-deposition of carbon atoms with hydrogen isotopes and hydrogenated carbon radicals and molecules is recognized as the main mechanism for tritium retention in the graphite walls of the previous tokamak fusion devices. Significant tritium retention would be a serious concern for safe and economic long-term operation of future fusion test reactors and fusion energy systems. Similar deposits are observed on the surface of the engineered components in a tritium-producing assembly, known as a Tritium-Producing Burnable Absorber Rod (TPBAR). Characterization of the deposits can help understand the tritium transport, accumulation history and distribution in TPBARs. This study reports our recent results from the carbonaceous deposits formed on an aluminide-coated cladding in the lower plenum of a TPBAR following thermal neutron irradiation. The observed deposits are amorphous in nature, consisting of flakes of interconnected nanoscale features. They contain primarily double-bonded carbon (e.g., alkene) and carbonyl carbon, as well as a minor fraction of aliphatic carbon, all of which are likely tritiated. A similar co-deposition process that occurred in previous fusion devices is responsible for the formation and growth of the carbonaceous deposits.

AbstractThis paper presents an experimental assessment of a blended fatigue‐extreme controller for load control employing trailing edge flaps on a lab‐scale wind turbine. The controller blends between a repetitive model predictive controller that targets fatigue loads and a dedicated extreme load controller, which consists of a simple on‐off load control strategy. The Fatigue controller uses the flapwise blade root bending moments of the three blades as input sensors. The Extreme controller additionally uses on‐blade angle of attack and velocity measurements as well as acceleration measurements to detect extreme events and to allow for a fast reaction. The experiments are conducted on the Berlin Research Turbine within the large wind tunnel of the TU Berlin. In order to reproduce test cases with deterministic extreme wind conditions that follow industry standards, the wind tunnel was redesigned. The analyzed test cases are extreme direction change, extreme coherent gust, extreme operating gust and extreme coherent gust with direction change. The test cases are analyzed by on‐blade angle of attack and velocity measurements. The load control performance of the Blended controller is compared to the pure fatigue oriented and the pure extreme load controller. The Blended controller achieves a maximum flapwise blade root bending moment reduction of 23%, which is comparable to the reduction achieved by the Extreme controller.

In the search for a nontoxic replacement of the commonly employed CdS buffer layer for Cu(In,Ga)(S,Se) $_\mathrm{2}$ based solar cells, chemically deposited Zn(O,S) thin films are a most promising choice. In this paper, we address the usually slow deposition speed of Zn(O,S) in a newly developed ammonia-free chemical bath process, resulting in a deposition of 30 nm in 3 min with good homogeneity on 30 cm × 30 cm sized substrates. Solar cells with buffer layers prepared from this process match the efficiency of CdS reference cells. In a second step, we address the light-soaking post-treatment, still needed for maximum efficiencies. By addition of aluminum to the deposition process, the initial efficiencies can be increased slightly. With the addition of boron, the light-soaking post-treatment is rendered unnecessary, while maintaining high efficiencies above 15%, surpassing reference cells with CdS buffer.

AbstractThis paper presents an understanding of the fundamental carrier transport mechanism in hydrogenated amorphous silicon (a‐Si:H)‐based n/p junctions. These n/p junctions are, then, used as tunneling and recombination junctions (TRJ) in tandem solar cells, which were constructed by stacking the a‐Si:H‐based solar cell on the heterojunction with intrinsic thin layer (HIT) cell. First, the effect of activation energy (Ea) and Urbach parameter (Eu) of n‐type hydrogenated amorphous silicon (a‐Si:H(n)) on current transport in an a‐Si:H‐based n/p TRJ has been investigated. The photoluminescence spectra and temperature‐dependent current–voltage characteristics in dark condition indicates that the tunneling is the dominant carrier transport mechanism in our a‐Si:H‐based n/p‐type TRJ. The fabrication of a tandem cell structure consists of an a‐Si:H‐based top cell and an HIT‐type bottom cell with the a‐Si:H‐based n/p junction developed as a TRJ in between. The development of a‐Si:H‐based n/p junction as a TRJ leads to an improved a‐Si:H/HIT‐type tandem cell with a better open circuit voltage (Voc), fill factor (FF), and efficiency. The improvements in the cell performance was attributed to the wider band‐tail states in the a‐Si:H(n) layer that helps to an enhanced tunneling and recombination process in the TRJ. The best photovoltage parameters of the tandem cell were found to be Voc = 1430 mV, short circuit current density = 10.51 mA/cm2, FF = 0.65, and efficiency = 9.75%. Copyright © 2015 John Wiley & Sons, Ltd.