• Energy Research
• 7. Clean energy close
• 13. Climate action close

The battery power state (SOP) is the basic indicator for the Battery management system (BMS) of the battery energy storage system (BESS) to formulate control strategies. Although there have been many studies on state estimation of lithium-ion batteries (LIBs), aging and temperature variation are seldom considered in peak power prediction during the whole life of the battery. To fill this gap, this paper aims to propose an adaptive peak power prediction method for power lithium-ion batteries considering temperature and aging is proposed. First, the Thevenin equivalent circuit model is used to jointly estimate the state of charge (SOC) and SOP of the lithium-ion power battery, and the variable forgetting factor recursive least squares (VFF-RLS) algorithm and extended Kalman filter (EKF) are utilized to identify the battery parameters online. Then, multiple constraint parameters including current, voltage, and SOC were derived, considering the dependence of the polarization resistance of the battery on the battery current. Finally, the verification experiment was carried out with LiFePO4 battery. The experimental results under FUDS operating conditions show that the maximum SOC estimation error is 1.94%. And the power prediction errors at 20%, 50%, and 70% SOC were 5.0%, 8.1% and 4.5%, respectively. Our further work will focus on the joint estimation of battery state to further improve the accuracy.

Abstract Pollution control strategies currently in use by electric power systems are reviewed and a new minimum emission dispatch (MED) method is developed. This new method minimizes overall emission levels at an increased cost in large-scale power systems while simultaneously accommodating local pollution level requirements, as well as economic constraints.

Comfort temperature and sleep quality involving 20 participants were determined in two cases: Case A (arbitrary, controlled air-conditioner setting) and Case B (adjustment of 3 °C higher than the setting of Case A with cool bed linen). Data of indoor thermal comfort and electricity consumption were collected every night throughout the measurement period. Questionnaires on thermal comfort and sleep quality were distributed twice a night for a duration of three nights for each case; the first night was for respondents’ adaptation and the following two nights were for measurement. The sleep quality of the respondents was objectively measured using a commercially available activity tracker. Results found that most respondents were thermally comfortable in both cases, with 39% lower energy consumption reported for Case B compared to Case A. The thermal conditions of Case B were found to be more tolerable than those of Case A. Most respondents reported to have a calm and satisfied sleep for both cases. Comfort temperature and Sleep Efficiency Index (SEI) were found to be maintained in both cases.

Given the considerable scale of distribution networks in urban and rural areas, as well as the lack of management records, adjustments of switches during the distribution system operation are poorly documented. Such deficiency results in the inaccuracy of models stored in the distribution network automation system, and thus misleads the state estimation. With the emergence of information and communication technology, a large number of the feeder and residential smart meter data are accumulated. Such data can help recognize the operation modes of distribution networks by analyzing the relationships between the on/off states of switches and the voltage correlations among buses. However, the limited quantity and quality of the sampling data restrict the implementation of data-driven recognition. In this paper, a physical-probabilistic-network (PPN) model applied for inferring overall operation mode of distribution networks is proposed. Based on which, a belief propagation-based algorithm is proposed for the inference even under situations when there are only partial bus voltages data available. Meanwhile, the required variable for inference can be reduced from the active trail analysis. Experiment results are used to compare its performance with classic methods and to prove its effectiveness and advantages.

This article examines land-use, market and welfare implications of lignocellulosic bioethanol production in Hawaii to satisfy 10% and 20% of the State's gasoline demand in line with the State's ethanol blending mandate and Alternative Fuels Standard (AFS). A static computable general equilibrium (CGE) model is used to evaluate four alternative support mechanisms for bioethanol. Namely: (i) a federal blending tax credit, (ii) a long-term purchase contract, (iii) a state production subsidy financed by a lump-sum tax and (iv) a state production subsidy financed by an ad valorem gasoline tax. We find that because Hawaii-produced bioethanol is relatively costly, all scenarios are welfare reducing for Hawaii residents: estimated between -0.14% and -0.32%. Unsurprisingly, Hawaii.s economy and its residents fair best under the federal blending tax credit scenario, with a positive impact to gross state product of $49 million. Otherwise, impacts to gross state product are negative (up to -$63 million). We additionally find that Hawaii-based bioethanol is not likely to offer substantial greenhouse gas emissions savings in comparison to imported biofuel, and as such the policy cost per tonne of emissions displaced ranges between $130 to $2,100/tonne of CO2e. The policies serve to increase the value of agricultural lands, where we estimate that the value of pasture land could increase as much as 150% in the 20% AFS scenario.

The focus of this research lies on fundamental research to provide guidelines for the design of new nanocatalyst toward improvement of the performance of proton exchange membrane fuel cells (PEMFCs). To achieve this overarching goal, several specific steps were taken with aims to: (1) provide guidelines for the design of new catalysts; (2) promote nanocatalyst applications towards alternative energy applications; and (3) integrate advanced instrumentation into nanocharacterization and fuel cell (FC) electrochemical behavior. In tandem with these goals, the cathode catalysts were extensively refined to improve the performance of PEMFCs and minimize noble metal usage. In this study, the major accomplishment was producing aligned carbon nanotubes (ACNTs), which were then modified by platinum (Pt) nanoparticles via a post-functionalization colloidal chemistry approach. The Pt-ACNTs demonstrated improved cathodic catalycity, by building better device endurance and decreased Pt loading. It was also determined that surface mechanical properties, such as elastic modulus and hardness were increased. Collectively, these enhancements provided an improved FC device. The electrochemical analyses indicated that the power density of the PEMFCs was increased to 900 mW/cm2 and current density to 3000 mA/cm2, respectively. The Pt loading was controlled at lower than 0.2 mg/cm2 to decrease the manufacturing expenses.

Air is a desirable alternative to the less environmental friendly SF6 in compact medium voltage switchgear. However, the poor thermal properties of air requires better thermal designs to keep the temperature rise within the allowable industry limits to avoid premature switch degradation. This publication focuses on the temperature rise of load break switches (LBS) of different designs. A LBS with flexible braid was found to have considerably higher temperature rise than a design with the sliding contact. The study has shown that a stripped switch (with only the current path) can be used together with empirical determined heat transfer coefficients in a first approach for predicting the temperature rise of the critical parts of the LBS. Aluminum construction elements functioning as heat sinks had a huge impact on the temperature rise of the LBS, and design elements that can utilize this might be important when replacing SF6 with air.

A range of optical fibre-based sensors for the measurement of ethanol, primarily in aqueous solution, have been developed and are reviewed here. The sensing approaches can be classified into four groups according to the measurement techniques used, namely absorption (or absorbance), external interferometric, internal fibre grating and plasmonic sensing. The sensors within these groupings can be compared in terms of their characteristic performance indicators, which include sensitivity, resolution and measurement range. Here, particular attention is paid to the potential application areas of these sensors as ethanol production is globally viewed as an important industrial activity. Potential industrial applications are highlighted in the context of the emergence of the internet of things (IoT), which is driving widespread utilization of these sensors in the commercially significant industrial and medical sectors. The review concludes with a summary of the current status and future prospects of optical fibre ethanol sensors for industrial use.