• Energy Research
• 2021-2025close
• Embargo close
• 7. Clean energy close

Materials:Rice straw, pine sawdust and Phoenix Tree's leaf were selected as the main biomass of this study. Algorithms and methods:Coats-Redfern integral method,Doyle method,Distribution Activation Energy Model (DAEM): The database contains all the original data, intermediate data and final results used in the paper. Fig. 1 was schematic diagram of WRT-3P high temperature TGA and gas flow routes Fig. 2 was influence of particle size on biomass pyrolysis kinetics (a) TG curves of rice straw (b) DTG curves of rice traw (c) TG curves of pine sawdust (d) DTG curves of pine sawdust (e) TG curves of Phoenix Tree's leaf (f) DTG curves of Phoenix Tree's leaf Fig. 3 was influence of heating rate on different biomass (rice straw, pine sawdust and Phoenix Tree's leaf) pyrolysis kinetics (a) TG curves of rice straw (b) DTG curves of rice traw (c) TG curves of pine sawdust (d) DTG curves of pine sawdust (e) TG curves of Phoenix Tree's leaf (f) DTG curves of Phoenix Tree's leaf Fig. 4 was potassium concentration of initial and soaked rice straw Fig. 5 was influence of K+ on rice straw pyrolysis kinetics (a) TG curves (b) DTG curves Fig. 6 was the relationship between and 1/T of three kinds of biomass with a particle size of 0.150 - 0.180 mm at different heating rates. (a) 5℃/min (b) 10℃/min (c) 20℃/min (d) 40℃/min Fig. 7 was the apparent activation energy of biomass pyrolysis obtained by DAEM.

Abstract With drastic fossil fuel depletion and environmental deterioration concerns, a move towards a more sustainable bioenergy-based economy is essential. Lately, the application of microwave (MW) irradiation for waste processing has been attracting interest globally. MW-assisted heating possesses several advantages such as the provision of high microwave energy into dielectric materials with deeper penetration for internal heat generation, showing beneficial features in improving the heating rate and reducing the reaction time. Consequently, the most recent literature regarding the applications of MW-assisted heating for biomass pretreatment as well as biofuel and bioenergy production was reviewed and consolidated in this study. An impressive increase in the product yield and improvement of the product properties are reported, with the use of MW-assisted heating in several conversion routes to produce biofuels. Despite being a promising technology for biofuel production, some major fundamental data of MW-assisted heating have not been comprehensively identified. Therefore, the feasibility of this technology for large-scale implementation is still subpar. Understanding the interaction between the feedstock and the microwave electromagnetic field, and the optimization of several operational and mechanical parameters are the two main keystones that would propel the industrialization of MW heating in the near future. This provides key insights leading to increased feasibility and more advanced application of MW heating.

The dataset is composed of the final energy consumption by sector (industry, passenger transport, freight transport, residential, services, and agriculture) and sub-sector/end-use (e.g., chemical industry, cars, truck and light vehicles, space heating, etc.) of Finland. In addition, data regarding passengers and goods traffic, the number of households, the stock of dwellings permanently occupied, the floor area of dwellings, and CO2 emissions are collected. The primary data source is the Odyssee database. The Odyssee data are complemented with data regarding the value added and energy dependence of Finland taken from the World Bank and Eurostat database, respectively. The data of Finland cover the period from 2005 to 2015.

Halide perovskites are the leading candidates for next-generation, low-cost optoelectronics with power conversion efficiencies well above 25%. However, operational stability remains a key challenge. Although there is an understanding that the microscale and nanoscale play a consequential role in determining the macroscopic performance and stability, significant gaps remain in the mechanistic understanding of degradation processes at the nanoscale and the mechanisms for stability in cation-alloyed systems. Nanoscale hexagonal phase impurities have been identified as problematic for operational stability, leading to both performance losses and morphological degradation. However, it is still unclear at what stage these phase impurities originate. Understanding this better is critical in order to mitigate the harmful effects of these phase impurities on performance and operational stability. Cation alloying is a commonly used technique in the field to mitigate these hexagonal phase impurities, although not without its challenges. In this thesis study, the nanoscale structural landscape of key halide perovskite compositions is studied. By taking snapshots of the perovskite at different states of the annealing process, the impact of phase impurities on device performance is characterised. Thereon, the mechanism by which composition dictates photostability in FA-rich perovskite absorber layers is studied. It is demonstrated that the composition impacts the degree of octahedral tilt, which is essential to restricting the transition to hexagonal phase impurities. Additionally, it is demonstrated that while a judicious mix of A-site cations can be used to stabilise the photoactive black phase of halide perovskites, it is challenging to achieve this homogeneously over large areas, necessitating a search for alternative or complementary approaches to stabilise perovskite via octahedral tilt. Using scanning electron diffraction (SED) studies, the spacegroup of additive-stabilised-CsPbI3 is demonstrated to be a low symmetry tilted γ-phase. Furthermore, using SED, the nanoscale structural landscape of mixed-phase CsPbI3 absorber layers is studied and it is demonstrated that both narrow-bandgap γ-phase and wide-bandgap δ-phase co-exist at the nanoscale, enabling stable and bright white-light emission. Overall, this thesis provides insights into the role of nanoscale structure in dictating the properties and behaviour of halide perovskites and offers rational guidelines for their optimisation and use in optoelectronic devices. Additionally, it is demonstrated that SED is a powerful tool for studying these materials at the atomic scale, allowing for the detailed characterisation of their structures and properties.

Formate production via both CO2 reduction and cellulose oxidation in a solar-driven process is achieved by a semiartificial biohybrid photocatalyst consisting of immobilized formate dehydrogenase on titanium dioxide (TiO2|FDH) producing up to 1.16±0.04 mmolformate gTiO2-1 in 24 hours. Isotopic labelling experiments with 13C-labelled substrates support the mechanism of stoichiometric formate formation through both redox half-reactions. TiO2|FDH was further immobilized on hollow glass microspheres to perform more practical floating photoreforming allowing vertical solar light illumination with optimal light exposure of the photocatalyst to real sunlight. Enzymatic cellulose depolymerization coupled to the floating photoreforming catalyst generates 0.36±0.04 mmolformate mirr-2 after 24 h. This work thus presents simultaneous solar-driven valorization of waste streams, demonstrates the advantages of biohybrid photocatalysts in photoreforming for the first time and will provide inspiration for the development of future semi-artificial waste-to-chemical conversion strategies.

One of the biggest challenges in converting wave energy is to enable the use of low frequency waves, since the highest waves in typical sea states have low frequencies, as can be seen from the corresponding wave spectra, such as the Pierson–Moskowitz or JONSWAP spectra. In this paper, we show that this challenge is indeed achievable for the operation of small autonomous drifting sensor platforms. We present the design and optimization of a compact wave energy converter that freely floats in random sea waves. An optimization of the dynamical behavior as well as the electromagnetic power take-off is conducted based on simulations and experiments. The platform has compact dimensions of 50 cm draft and 50 cm diameter, which leads to special requirements for size and appearance. To meet these requirements, a two-body self-reacting point absorber is designed and a flux switching permanent magnet linear machine is developed for the power take-off. The developed system is validated by experiments in a wave flume and the linear generator is analyzed on a test bench. A coupled model is used to simulate and optimize the corresponding mechanical system, which leads to an increased output power from below 10 mW for the simulated initial setup to a power output of more than 100 mW in the simulation. Simulations and experiments are performed for regular and random waves in order to provide realistic approximations of the total output power.

Over the past decade, lead-halide perovskites (LHPs) have demonstrated significant potential in terms of their performance across a wide range of optoelectronic devices, including solar cells, photodetectors and light-emitting diodes. However, the toxicity of lead and instability issue of LHPs are still concerns for their widespread implementation. These successes, but also the challenges of LHPs have motivated great efforts across multiple disciplines to search for lead-free and stable alternatives that can have similar optoelectronic properties to LHPs, namely ‘perovskite-inspired materials (PIMs)’. With the deeper understanding of defect tolerance displayed in LHPs, a large number of PIMs have been identified until now. Among all the identified PIMs, ternary chalcogenides or ABZ2 materials, are believed to be one of the most promising alternatives so far, owing to their simple fabrication protocols, strong absorption and high stability in air. Particularly, AgBiS2 solar cells have demonstrated the highest efficiency (9.17%) among all bismuth-based solar cells. Nevertheless, studies into ternary chalcogenides are mostly limited to AgBiS2 photovoltaics, and the investigations into other potential ABZ2 materials or broader applications are rare so far. Therefore, this thesis will aim to investigate the optoelectronic properties of another promising while rarely investigated ABZ2 material – NaBiS2, and also the potential of AgBiS2 as near-infrared (NIR) photodetectors. In the first project of this thesis, NaBiS2 nanocrystals (NCs) have been shown to exhibit extremely strong absorption, along with a comparatively sharp absorption onset. However, optical-pump-terahertz-probe (OPTP) measurements indicated that most free charge-carriers in NaBiS2 NCs will be localised within a few picoseconds. These localised charge-carriers only exhibited low mobility of around 0.03 cm2 V-1 s-1 and could not transport effectively even though they might be rather long-lived in NaBiS2 and unaffected by intentionally-introduced defects. With help from density functional theory (DFT) calculations, all of these unusual characteristics in NaBiS2 have been shown to closely associate with intrinsic cation disorder, which was also observed in AgBiS2. Although post-annealing is effective for improving cation inhomogeneity and enhancing absorption in AgBiS2, its effect on NaBiS2 was found to be rather minor, which also indicated that the charge-carrier localisation process in NaBiS2 could not be significantly mitigated after annealing. Based on the fundamental insights acquired in the first project, the possibility of further improving charge-carrier transport in NaBiS2 NCs through ligand exchange treatment was investigated in my second project. Using a variety of correlated spectroscopic characterisation techniques, I found that NaBiS2 NCs treated by inorganic iodide ligands had enhanced sum mobility and surface photovoltage (SPV) signals, which implies an improvement in the macroscopic charge-carrier transport. However, the ultrafast localisation process was still observed in these iodide-treated NaBiS2 NCs, suggesting that their cation disorder was not greatly changed. At the same time, the defect capture rates were also found to be lower in the iodide-treated NaBiS2 NCs based on my two proposed models for describing charge-carrier dynamics. As a result, solar cells based on these iodide-treated NaBiS2 NCs could exhibit a peak external quantum efficiency (EQE) value over 50%, along with a power conversion efficiency exceeding 0.7%. Although this is an order of magnitude larger than previous reports, I found ion migration to be a limiting factor for NaBiS2 devices from temperature-dependent transient current measurements, where a low activation energy of only 88 meV was extracted. In my third project, AgBiS2 photodetectors were fabricated and characterised in depth. Aside from the broadband photo-response across from ultra-violet (UV) to near-infrared (NIR) region, AgBiS2 photodetectors have demonstrated an extremely high cut-off frequency (f-3dB) on MHz order, indicating their great potential in applications requiring fast device response such as optical communications. The mechanism behind this fast response was studied, and a relatively long drift length compared to the AgBiS2 film thickness is believed to be the key reason. Similar to NaBiS2 devices, ion migration was also found easy in AgBiS2 devices with an activation energy of 124 meV, which could lead to their increasing noise currents with time. Importantly, these noise currents could be also effectively suppressed when optimising the AgBiS2 film thickness, in which a balance between large shunt resistant and cumulative quantity of defects should be reached. Finally, owing to the small bandgap of AgBiS2 NCs (~1.2 eV), AgBiS2 photodetectors could effectively monitor the heartbeat rates by probing the transmission change of blood vessels illuminated by NIR light, which has been widely used in the medical field owing to its deeper penetration in tissues. These three projects not only uncovered several remarkable optoelectronic characteristics of ABZ2 materials, but also investigated possible methods to further alter these characteristics. Although ABZ2 materials have shown great potential as light harvesters, it can be seen that both cation disorder (or charge-carrier localisation) and ion migration are still limiting the performance. More studies on the root causes of both phenomena, and how to effectively suppress their effects on the materials, would be hence crucial in the future work. With more understandings on this material class, we could expect more efficient, stable, and cleaner optoelectronic devices to be realised in the future.

The file contains all data used for the analysis underlying the paper "SUBSIDISATION COST ANALYSIS OF RENEWABLE ENERGY DEPLOYMENT: A CASE STUDY ON THE ITALIAN FEED-IN TARIFF PROGRAMME FOR PHOTOVOLTAICS"

All data presented in the article have been uploaded here.