• Energy Research
• 2021-2025close
• IT close
• UA close
• Aurora Universities Network close

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method’s capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm2. Results highlight the method’s potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

Dolomite-based binders are characterised by interesting technical and environmental features. For their synthesis, sources of both CaO and MgO are required. The idea developed in this work is to couple the synthesis of dolomite-based binders, starting from a natural dolomite, through the concept of concentrated solar energy (needed to drive the endothermal dolomite calcination process) in fluidised bed reactors. To this end, a fluidised bed system, where the concentrated solar radiation is mimicked by the use of Xe-lamps (short-arc), has been set up and operated. Natural dolomite (sieved in the 420-590 ?m size range) was calcined at a nominal temperature of 850 °C, and bed temperature profiles during solar-driven calcination were investigated. Then, four binders were prepared by mixing slaked dolomite (obtained from the hydration of solar calcined dolomite) with either blast furnace slag or coal fly ash as supplementary cementitious materials. The binders were hydrated for curing times ranging from 7 to 56 days. X-ray fluorescence, X-ray diffraction and combined differential thermal and thermogravimetric analyses were employed as characterisation techniques both to analyse the chemical composition of starting materials and to investigate the evolution of the hydration in the four systems.

Battery participation in the service of power system frequency regulation is universally recognized as a viable means for counteracting the dramatic impact of the increasing utilization of renewable energy sources. One of the most complex aspects, in both the planning and operation stage, is the adequate characterization of the dynamic variation of the state of charge of the battery in view of lifetime preservation as well as the adequate participation in the regulation task. Since the power system frequency, which is the input of the battery regulation service, is inherently of a stochastic nature, it is easy to argue that the most proper methodology for addressing this complex issue is that of the theory of stochastic processes. In the first part of the paper, a preliminary characterization of the power system frequency is presented by showing that with an optimal degree of approximation it can be regarded as an Ornstein–Uhlenbeck process. Some considerations for guaranteeing desirable performances of the control strategy are performed by assuming that the battery-regulating power depending on the frequency can be described by means of a Wiener process. In the second part of the paper, more realistically, the regulating power due to power system changes is described as an Ornstein–Uhlenbeck or an exponential shot noise process driven by a homogeneous Poisson process depending on the frequency response features requested of the battery. Because of that, the battery state of charge is modeled as the output of a dynamic filter having this exponential shot noise process as input and its characterization constitutes the central role for the correct characterization of the battery life. Numerical simulations are carried out for demonstrating the goodness and the applicability of the proposed probabilistic approach.

In this paper a grid-tied photovoltaic (PV) cascaded H-bridge (CHB) inverter with embedded storage units is proposed. The multi-input single-output inverter architecture allows a distributed maximum power point tracking (DMPPT) approach, thus mitigating the mismatch effects. The energy storage units (ESUs) embedded at each dc-link provides more flexibility to the power circuit compensating for the inherent variability of the PV sources. The proposed power system ensures a continuous power supply to the grid also in case of PV power fluctuations due to irradiance conditions as well as to the MPPT. In particular, the presence of a storage element allows a voltage sweep on the PV source to be implemented, thus guaranteeing the maximization of PV energy harvesting, with no detrimental effect on the power delivery to the utility network. The numerical results, carried out on a single-phase nineteen-level PV CHB inverter, reveal the improved performance of the proposed design and control technique.

Marine fungi are widely distributed in the ocean, playing an important role in the ecosystems, but only little information is available about their occurrence and activity. Seagrass bleaching is also a neglected phenomenon that seems to be linked to warm environments, even though the causes are still to be defined. In this study, the cultivable mycoflora associated to the leaf conditions (bleached, necrotic and live) and section (from the base to the tip) in the seagrass Posidonia oceanica was investigated in a Mediterranean warm-edge location (Cyprus). A total of 17 Ascomycota species/taxon were identified and results highlighted that mycoflora composition changed significantly in relation to both the leaf condition and section. A few known pathogens of terrestrial plants were detected only on bleached leaves, but it remains unknown whether they have any direct connections with P. oceanica bleaching phenomenon.

The International Atomic Energy Agency (IAEA), jointly with the World Health Organization (WHO), has operated a postal dosimetry audit program for radiotherapy centers worldwide since 1969. In 2017 the IAEA introduced a new methodology based on radiophotoluminescent dosimetry (RPLD) for these audits. The detection system consists of a phosphate glass dosimeter inserted in a plastic capsule that is kept in measuring position with a PMMA holder during irradiation. Correction factors for this holder were obtained using experimental methods. In this work these methods are described and the resulting factors are verified by means of Monte Carlo simulation with the general-purpose code PENELOPE for a range of photon beam qualities relevant in radiotherapy. The study relies on a detailed geometrical representation of the experimental setup. Various photon beams were obtained from faithful modeling of the corresponding linacs. Monte Carlo simulation transport parameters are selected to ensure subpercent accuracy. The simulated correction factors fall in the interval 1.005-1.008 (±0.2%), with deviations with respect to experimental values not larger than 0.2(2)%. This study corroborates the validity of the holder correction factors currently used for the IAEA audits.

Solid-state refrigeration based on the caloric effects has recently received widespread consideration because of its high efficiency and environmental protection. Compared with other solid-state refrigeration technologies, the elastocaloric effect-based one has great application potential. The elastoCaloric Effect (eCE) is defined as the reversible adiabatic temperature change (ΔTad) and the reversible isothermal entropy change (ΔST) in Shape Memory Alloys (SMA), following a variation in the mechanical field applied. To date, the elastocaloric materials, considered as benchmark, since offering the best compromise between thermal and mechanical performances are represented by the NiTi binary alloys.