• Energy Research
• Closed Access close
• Embargo close
• DE close
• IT close
• BE close
• Energy Research close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

Changes in the main weather features are becoming perceivable in Italy. In the last years, the average temperature and the intensity of rainstorms are increasing. Such phenomena could lead to changes in the earth-atmosphere interaction. Accounting for the high vulnerability of the Italian territory, an obvious consequence would concern the effects on the hydro-geological hazards, including landslides and floods. As a matter of fact, the higher frequency of high magnitude flood and landslide events represent an alarm bell. It is necessary to explore with all available instruments the consequences of the potential climate changes. Since quantitative predictions are not possible, the only way to run is depicting rational scenarios for the most vulnerable contexts adopting a multidisciplinary approach. Based on projections of potential climate changes in the 21st century, the report examines their potential impact in the context of the Italian peninsula. After a general overview about typical slope responses to weather changes, some quantitative scenarios have been depicted for representative geomorphological contexts. The last part of the paper examines changes in the expected risk, based on the characteristics of the Italian territory and its vulnerability, looking at the initiatives to undertake for its mitigation.

The electrical resistance of Ni 50 Ti 30 Hf 20 and Ni 50 Ti 40.5 Hf 9.5 alloys during Stress Assisted Two Way Memory Effect was investigated with the aim to deduce the relationship between electrical resistance and deformation across the transformation range. Results show an almost linear relationship although a crossing point between increasing and decreasing deformation may compromise the use of these alloys actuators.

The passivation of iron and steel (DIN 1623) was studied by integral and depth selective conversion electron Mossbauer spectroscopy and Auger electron spectroscopy. Thickness and phase composition of the passive layer formed in sulphate solution and in a phosphate buffer were determined in dependence on the anodic potential and the duration of the passivating procedure. The experimental results lead to the conclusion that not the whole oxidic layer is responsible for the passivity but only a very thin intermediate layer formed between the cubic substrate and the rhombic oxide (γ-FeOOH) cover.

Current energy market designs and pricing schemes fail to give investors the appropriate market signals. In particular, energy prices are not high enough to attract investors to build new or maintain existing power capacity. In this paper we propose a method to compute second-best Pareto optimal equilibrium prices for any market exhibiting non-convexities and, based on this result, an energy market design able to restore the correct energy price signals for supply investors.

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.

Seagrass systems of the Western Pacific region are biodiverse habitats, providing vital services to ecosystems and humans over a vast geographic range. SeagrassNet is a worldwide monitoring program that collects data on seagrass habitats, including the ten locations across the Western Pacific reported here where change at various scales was rapidly detected. Three sites remote from human influence were stable. Seagrasses declined largely due to increased nutrient loading (4 sites) and increased sedimentation (3 sites), the two most common stressors of seagrass worldwide. Two sites experienced near-total loss from of excess sedimentation, followed by partial recovery once sedimentation was reduced. Species shifts were observed at every site with recovering sites colonized by pioneer species. Regulation of watersheds is essential if marine protected areas are to preserve seagrass meadows. Seagrasses in the Western Pacific experience stress due to human impacts despite the vastness of the ocean area and low development pressures.

Abstract In many visions and roadmaps, there is a broad agreement that fuel cells – both for stationary and mobile applications – are the key technology to allow the development of a hydrogen infrastructure. Furthermore, this development is generally thought to be based on a gradual, decentralised evolution. Nevertheless, in this paper it is argued that, taking into account the entire hydrogen chain (production, transport, storage, distribution and end-use), this decentralised fuel-cell based philosophy shows some serious flaws. Therefore, a new hydrogen-transition approach was pushed forward: mixing in of hydrogen into the natural-gas bulk. Using Flanders – the Northern part of Belgium – as a case study, the development of a transitory hydrogen infrastructure has been studied, taking into account the entire hydrogen chain and its dynamics, from production to end use. In a next step, this transition is being quantified. An optimisation model has been developed using Matlab and the commercial solvers GAMS and CPLEX. Following a mixed-integer linear-programming approach, this model is able to determine the economically optimal hydrogen-production mix and operational behaviour of each hydrogen-production plant separately. The model then allows gaining valuable insights in the importance of storage and the influence of fuel prices and carbon taxes with regard to the development of an early hydrogen economy.

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

Abstract The elemental dissolution of Cu-Zn alloys was investigated as a function of Zn content ranging from 0 to 45 wt%. Atomic emission spectroelectrochemistry (AESEC) was utilized to directly monitor Cu2+ and Zn2+ release and oxide growth as function of time during potentiodynamic experiments. It was determined that Cu dissolution undergoes a simultaneous mechanism of Cu2O formation and Cu2+ release. The addition of Zn in Cu-Zn alloy does not measurably change the dissolution mechanism of Cu2+ and the rate of aqueous Cu2+ was only dependent on the potential. Zn dissolution was however blocked by the formation of a Cu(0) film which shifted the Zn dissolution in the anodic direction.