• Energy Research
• Closed Access close
• Open Source close
• Embargo close
• Energy Research close

Abstract In this work addition of ethanol to high viscosity jatropha methyl ester (JME) through port injection is investigated in order to determine its effect fuel viscosity reduction on diesel engine performance. In addition to viscosity alteration, the impact of ethanol addition on combustion characteristics such as combustion duration, ignition delay and emissions levels from diesel engines fuelled with blends of ethanol, diesel and JME is studied in particular. It is found that blending of oxygenated fuels with diesel modifies the chemical structure and physical properties which again alter the engine operating conditions, combustion parameters and emissions levels. However, the injection of only 5% ethanol through port injection allows for a total of 25% blending of biofuels into diesel yet keeping the fuel characteristics close to that of conventional diesel. However, both experimental and numerical results show that ethanol addition in JME blended diesel results in a slight increase in fuel consumption and thermal efficiency for the same power outputs as that of conventional diesel fuel. Also, the combustion characteristics with ethanol addition include improved maximum in-cylinder peak pressure, cumulative heat release (CHR) rate of heat release (ROHR), in-cylinder peak temperature and combustion duration. Regarding emission characteristics the experimental results show significant reduction in smoke, carbon monoxide (CO) and total hydrocarbon (THC) emissions with extended oxygen mass percentage in the fuel at higher engine loads. However, oxides of nitrogen (NOx) emissions are found to increase at high loads although the common tradeoff between smoke and NOx is found to be more prominent for the oxygenated fuels.

Abstract Socio-technical transformations towards low-carbon energy systems are on the way in developed countries. Conversely, developing countries tend to be locked in fossil fuels and foster coal-based energy structures, emphasizing reliable and cost-effective energy provision and sidelining environmental concerns. In this study, we identified and analysed the predominant factors related to coal-based power generation in Bangladesh. We applied a mixed-method approach, initially conducting a systematic literature review and, subsequently, semi-structured expert interviews to identify and validate relevant factors. We then assessed their relative importance using an Analytical Hierarchy Process based on expert judgments. The results of this assessment reveal that socio-economic aspects and environmental issues scored highest, while technological aspects and sector regulations were considered to be less relevant for large-scale coal power implementation. We conclude that future energy policies created in Bangladesh will need to use appropriate legal instruments and address issues such as human displacement and resettlement, low levels of public acceptance, health hazards and environmental pollution. Participative policy frameworks should be deployed in coal plant projects, and active monitoring systems are necessary to reduce the negative consequences associated with increased electrification and energy consumption. To address foreseeable structural challenges, it furthermore will be crucial to explore sustainable alternatives.

Abstract A great deal of heat is wasted in intensive public shower facilities, such as those in schools, barracks and natatoriums, which open up at specified time. It will contribute a lot to energy saving and environmental protection with significant economic benefits to recycle the exhaust heat. In this paper, we propose two different kinds of heat pumps (an electric heat pump and an absorption heat pump) in the heat recovery systems. In both system, the used shower water is drained through a pipe and collected in a gray water pool. When the wastewater reaches certain volume, the heat pump system will begin working and recycling heat. The wastewater is filtered and piped to the heat exchanger to exchange heat with the tap water whose temperature will increase from 12 °C to 25 °C with the wastewater temperature dropping from 30 °C to 17 °C. Then the wastewater is piped to the heat pump evaporator and the tap water is piped to the condenser for farther heating. According to the different characteristics of the electric heat pump and absorption heat pump, we also introduce the processes and control methods of different heat recovery systems in details in this paper. Based on a practical example, this paper analyzes and compares the economic and environmental benefits of three retrofitting schemes, including “exhaust heat recovery using electric heat pump”, “exhaust heat recovery using electric heat pump + gas boiler” and “exhaust heat recovery using direct-fired heat pump”. Then we find out that the heat recovery system using direct-fired absorption heat pump has lower energy consumption, less pollution, lower operating cost, and shorter payback period. And it has a promising practical application.

Simulation of air infiltration and ventilation, and heat transfer processes of buildings are combined in a building simulation program called BUS (version 3.2). The program applies and includes an effective sparse matrix solution method for a linear set of equations. A network assumption is adopted for both air flow and thermal simulation. An iterative method, based on the SIMPLE algorithm, is used for airflow simulation, and the lumped capacitance method is selected for thermal simulation. This building simulation program BUS includes mass balance, momentum, and heat balance equations. This makes it possible to lake into consideration the interaction between ventilation and heat transfer processes, obtain more reliable simulation results than previously, and simulate time-dependent processes.

Abstract Double and added double stage organic Rankine cycle systems are configured to recover exhaust gas waste heat of dual fuel engines. To evaluate the performance of the models proposed here, energy, exergy and economic analyses are performed. Several working fluids are evaluated for recommendation for double and added double stage organic Rankine cycle systems. In the double stage organic Rankine cycle, cycle 1 and cycle 2 are connected in parallel. Working fluids R123, R141b, and R601 are used in cycle 1, and R245fa, R236ea, and R1233zd in cycle 2. In the double stage organic Rankine cycle, the working fluid combinations of R601-R1233zd, R601-R245fa and R123-R245fa show better performance when considering power, heat transfer area and payback period, which are 1760 kW, 2108.9 m2 and 4.21 year, respectively for R601-R245fa. In the added double stage organic Rankine cycle, cycle 1 and cycle 2 are connected in two stages and cycle 1 and cycle 3 in parallel. The net power of the working fluid combinations of R123-R245fa and R123-R1233zd are 1799 kW and 1782 kW, respectively, which are higher than those of the others. Further, for R123-R245fa, the heat transfer area and payback period are 3352 m2 and 6.20 year, respectively, which is better compared to those of other working fluid combinations.

Abstract Additional experimental data concerning the kinetics of Ni-Mo codeposition were obtained by investigating cathodic polarization using a rotating disc electrode. The Ni-Mo alloys were deposited from an ammonium citrate bath. The alloy deposition was controlled by activation in the case of low values of the cathode potential and by diffusion in the case of higher values. The hydrogen discharge was found to be diffusion controlled. The inductive influence of nickel results in depolarization of the reduction of molybdenum which cannot be deposited separately. An increase in the disc rotation speed caused an increase in the maximum cathode efficiency and in the molybdenum content of the alloy.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

Abstract Pollution control strategies currently in use by electric power systems are reviewed and a new minimum emission dispatch (MED) method is developed. This new method minimizes overall emission levels at an increased cost in large-scale power systems while simultaneously accommodating local pollution level requirements, as well as economic constraints.