• Energy Research
• Closed Access close
• engineering and technology close
• CA close
• IR close
• AU close

Abstract This research attempted to analyze a triple-tube heat exchanger (TTHE) fitted with innovative crimped-spiral ribs to enhance thermal efficiency. The crimped-spiral rib was placed on the top of the internal tube, and the water–alumina nanofluid was employed as the hot fluid within the ribbed side, whereas the two other fluids were pure water. The numerical solutions were performed through the two-phase mixture method, while the turbulent flow was modeled via the Reynolds Stress Model (RSM). The overall heat transfer coefficient (U), heat transfer rate, effectiveness, and performance index enhanced remarkably by using the nanofluid. The greatest increment in the U and effectiveness reached around 44.91 and 41 %, respectively, by the increment of the volume fraction by 0.02. The crimp intensity had an appreciable contribution to the thermal performance. The main mechanism was stronger swirl flow generated by the crimped-spiral rib that yielded boundary layer destruction. The heat transfer capability was increased via the rib pitch decrement and rib height increment. The performance index showed great values even at low volume fractions, which manifested the great merit of the implemented refinements. The thermal attributes were investigated at the first of the result section and then, the hydraulic characteristics were researched.

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

Abstract Concerns about power quality (PQ) in distribution networks have necessitated the use of PQ measuring/monitoring equipment to detect and analyse PQ problems. As the installation of such equipment at all locations is not economically feasible, minimum number and optimum locations of PQ monitors have been sought in recent researches to meet both economical efficiency and monitoring capability. Focusing on voltage sags, this paper attempts to further reduce the number of PQ monitors obtained by optimum allocation approaches while keeping the desired monitoring capability. Growing number of electric equipment with high sensitivity to voltage sags have raised more concerns about financial losses associated with voltage sags in comparison to other PQ problems. Here, a neural estimator placed at a monitored location is proposed to estimate instantaneous voltage-sag waveforms of a non-monitored sensitive load using local measurements. Echo state network (ESN) is used as the voltage-sag waveform estimator (VSWE). Because of increasing penetration of distributed generations (DGs) and their impacts on voltage-sag performance, they are considered to challenge the estimation task. The proposed ESN-based VSWE is examined on the IEEE 37-bus network. Tests for extensive unseen cases with different fault resistances, fault inception-angles, fault locations and fault types under different load demands and network conditions show acceptable high accuracy of estimations during fault and fault clearing sequences. Furthermore, the performance of the VSWE is investigated during transients due to switching capacitors, DGs, loads and lines.

Abstract Gas cyclone separators have been widely used in different industries. In this study, to find the best geometrical ratios of Stairmand cyclone separator, computational fluid dynamics (CFD), design of experiments (DOE), multi-gene genetic programming (MGGP), and ten meta-heuristic algorithms were combined. Six geometrical dimensions of the gas cyclone separator including inlet height and width, vortex finder length and its diameter, cylinder height and cone-tip diameter were optimized. The obtained models from MGGP were optimized by ten meta-heuristic algorithms and non-dominated Pareto fronts were analyzed using six unary and binary metrics and PROMETHEE II as a decision making method. According to the optimization results, multi-objective Particle Swarm Optimization (MOPSO) showed the best performance and generated more preferred designs than Stairmand design compared to other algorithms. These preferred designs increased the collection efficiency within 0.36 to 6% and decreased the pressure drop within 3.3 to 27.5% compared to the Stairmand.

A detailed analysis of the effects of ground grid configuration on grounding performance has been carried out for uniform and horizontally stratified soils with multiple layers. The results of the analysis reveal that the most efficient and cost-effective design is highly dependent on soil structure type and characteristics. In the absence of ground rods, grounding grids with uniform mesh size are quite efficient in soils having a thin (relative to grid size) high resistivity (relative to the lower layers) top soil, while grids with small mesh size at the periphery of the grid provide optimum performance in uniform soils and soils with low resistivity top soils. Ground rods were found to be effective only when a significant portion of their length is in contact with a low resistivity soil, as expected.

Short-term generation scheduling is an important function in daily operational planning of power systems. It is defined as optimal scheduling of power generators over a scheduling period while respecting various generator constraints and system constraints. Objective of the problem includes costs associated with energy production, start-up cost and shut-down cost along with profits. The resulting problem is a large scale nonlinear mixed-integer optimization problem for which there is no exact solution technique available. The solution to the problem can be obtained only by complete enumeration, often at the cost of a prohibitively computation time requirement for realistic power systems. This paper presents a hybrid algorithm which combines Lagrangian Relaxation (LR) together with Evolutionary Algorithm (EA) to solve the problem in cooperative and competitive energy environments. Simulation studies were carried out on different systems containing various numbers of units. The outcomes from different algorithms are compared with that from the proposed hybrid algorithm and the advantages of the proposed algorithm are briefly discussed.

This paper presents a novel modified interactive honey bee mating optimization (IHBMO) base fuzzy stochastic long-term approach for determining optimum location and size of distributed energy resources (DERs). The Monte Carlo simulation method is used to model the uncertainties associated with long-term load forecasting. A proper combination of several objectives is considered in the objective function. Reduction of loss and power purchased from the electricity market, loss reduction in peak load level and reduction in voltage deviation are considered simultaneously as the objective functions. First, these objectives are fuzzified and designed to be comparable with each other. Then, they are introduced into an IHBMO algorithm in order to obtain the solution which maximizes the value of integrated objective function. The output power of DERs is scheduled for each load level. An enhanced economic model is also proposed to justify investment on DER. An IEEE 30-bus radial distribution test system is used to illustrate the effectiveness of the proposed method.

Abstract Bio-based polyurethane (BPU) foams were successfully prepared using hydrothermally liquefied wheat straw (WS) to substitute a mass fraction of up to 50% of polyols. Response surface methodology (RSM) based on central composite design (CCD) was employed to optimize four process parameters: NCO/OH molar ratio, loading of crosslinking agent (glycerol), loading of catalyst (a mixture of triethylene diamine, stannous octoate, and triethanolamine), and loading of blowing agent (water) for the maximum compression strength of the rigid BPU foams. With the quadratic orthogonal regression model, verified by experimentation, the maximum compression strength of approximately 180 kPa was obtained at the following optimal conditions: NCO/OH molar ratio of 1.24:1, glycerol addition of 12.11%, catalyst loading of 0.76%, and blowing agent addition of 1.31% in relation to the total mass of polyols. The BPU foam prepared at the optimal conditions exhibits good thermal conductivity (0.045 Wm−1K−1) and thermal stability, comparable to those of a reference foam prepared with 100% PPG400.

Abstract In-core nuclear fuel management is one of the most important concerns in the design of nuclear reactors. Two main goals in core fuel loading pattern design optimization are maximizing the core effective multiplication factor in order to extract the maximum energy, and keeping the local power peaking factor lower than a predetermined value to maintain the fuel integrity. Because of the numerous possible patterns of fuel assemblies in the reactor core, finding the best configuration is so important and challenging. Different techniques for optimization of fuel loading pattern in the reactor core have been introduced by now. In this study, a software is programmed in C# language to find an order of the fuel loading pattern of a VVER-1000 reactor core using the perturbation theory. Our optimization method is based on minimizing the radial power peaking factor. The optimization process launches by considering an initial loading pattern and the specifications of the fuel assemblies which are given as the input of the software. The results on a typical VVER-1000 reactor reveal that the method could reach to a pattern with an allowed radial power peaking factor and increases the cycle length 1.1 days, as well.