• Energy Research
• natural sciences close
• CA close
• Energies close

Reduced order models (ROMs) are increasingly applied to entrained flow gasification development due to reduced computational requirements relative to computational fluid dynamics (CFD) models. However, they require greater a posteriori knowledge of the reactor physics. A significant parameter influencing ROM outputs is the jet half-angle of the solid fuel and oxidant mixture in the gasifier. Thus, it is important to understand the geometry of the jet in the gasifier, and how it is dependent on operating parameters, such as solid and carrier gas flow rates. In this work, an existing model for jet half-angles, which considers the ratio of surrounding gas density to jet core density, is extended to a dry solids jet with impinging gas. The model is fitted to experimental jet half-angles. The jet half-angle of a non-reactive flow was measured using laser-sheet imaging for solid fluxes in the range of 460–880 kg/m2·s and carrier gas fluxes in the range of 43–90 kg/m2·s at the transport line outlet. Jet half-angles ranged from 5.6° to 11.3°, increasing with lower solid/gas loading ratios. CFD simulations of two reactive conditions, with solid and gas fluxes similar to experiments, were used to test the applicability of the proposed jet half-angle model.

Numerical calculations are performed to determine the potential of using one-dimensional transparent photonic crystal heat mirrors (TPCHMs) as transparent coatings for solar receivers. At relatively low operating temperatures of 500 K, the TPCHMs investigated herein do not provide a significant advantage over conventional transparent heat mirrors that are made using transparent conducting oxide films. However, the results show that TPCHMs can enhance the performance of transparent solar receiver covers at higher operating temperatures. At 1000 K, the amount of radiation reflected by a transparent cover back to the receiver can be increased from 40.4% to 60.0%, without compromising the transmittance of solar radiation through the cover, by using a TPCHM in the place of a conventional transparent mirror with a In2O3:Sn film. For a receiver operating temperature of 1500 K, the amount of radiation reflected back to the receiver can be increased from 25.7% for a cover that is coated with a In2O3:Sn film to 57.6% for a cover with a TPCHM. The TPCHM that is presented in this work might be useful for high-temperature applications where high-performance is required over a relatively small area, such as the cover for evacuated receivers or volumetric receivers in Sterling engines.

The purpose of this investigation was the development of a new colloidal route for the fabrication of Mn3O4 electrodes for supercapacitors with enhanced charge storage performance. Mn3O4-carbon nanotube electrodes were fabricated with record-high capacitances of 6.67 F cm−2 obtained from cyclic voltammetry tests at a scan rate of 2 mV s−1 and 7.55 F cm−2 obtained from the galvanostatic charge–discharge tests at a current density of 3 mA cm−2 in 0.5 M Na2SO4 electrolyte in a potential window of 0.9 V. The approach involves the use of murexide as a capping agent for the synthesis of Mn3O4 and a co-dispersant for Mn3O4 and carbon nanotubes. Good electrochemical performance of the electrode material was achieved at a high active mass loading of 40 mg cm−2 and was linked to a reduced agglomeration of Mn3O4 nanoparticles and efficient co-dispersion of Mn3O4 with carbon nanotubes. The mechanisms of murexide adsorption on Mn3O4 and carbon nanotube are discussed. With the proposed method, the time-consuming electrode activation procedure for Mn3O4 electrodes can be avoided. The approach developed in this investigation paves the way for the fabrication of advanced cathodes for asymmetric supercapacitors and multifunctional devices, combining capacitive, magnetic, and other functional properties.

Biogas technology is an important alternative energy source worldwide. Blackwater and kitchen refuse represent ideal waste streams for bioenergy recovery through anaerobic co-digestion. Modeling of the biokinetics of anaerobic digestion on several aspects, such as microbial activity, substrate degradation, and methane production, from co-digestion of black water (BW) and kitchen refuse (KR) was the objective of this research. A mathematical model was developed towards a simulation based on mass balances on biomass, the organic substrate, and biogas. The model was implemented in INSEL and experimental data from the literature were used for model validation. The study shows that the simulation results fit well with the experimental data. The energy consumption and generation potential of anaerobic co-digestion of BW and KR were calculated to investigate if the produced biogas could supply the digester’s energy demand. This study can be used to pre-design anaerobic digestion systems in eco-districts.

Focusing on the influence of fine metal particles on the insulation characteristics of outdoor insulators, spherical micrometer-level iron powders were used to represent fine metal particles of different parameters on a polymer insulator specimen surface. Dynamic movement and lift-off behavior of fine particles, as well as the triggered surface discharges under AC voltage were investigated in a uniform electric field under different experimental conditions. The results reveal that the inception, propagation and intensity of surface discharges are significantly affected by the particle parameters, including particle size, amount and distributing characteristic. Based on the measurement of light emission during the flashover process using a high-speed camera, the process of surface discharge to flashover triggered by the fine metal particles were investigated to obtain a relationship between flashover voltage, discharge light intensity and particle parameters. It is suggested that particle size smaller than 28 µm and particle amount more than 40 mg in contact with the non-uniform distribution can cause a significant distortion and intensification of the electric field resulting in a higher risk of surface discharges leading to flashover. Such investigations can enhance the operating reliability of outdoor insulators subjected to these conditions.

Higher-voltage-standard and higher-power-rating aerospace power systems are being investigated intensively in the aerospace industry to address challenges in terms of improving emissions, fuel economy, and also cost. Multilevel converter topologies become attractive because of their higher efficiency under high-voltage and high-switching-frequency conditions. In this paper, an asymmetrical-voltage-level back-to-back multilevel converter is proposed, which consists of a five-level (5L) rectifier stage and a three-level (3L) inverter stage. Based on the comparison, such an asymmetrical back-to-back structure can achieve high efficiency and minimize the converter weight on both rectifier and inverter sides. A compact triple-surface-mounted heatsink structure is designed to realize high density and manufacturable thermal management. This topology and structure are evaluated with a full-rating prototype. According to the evaluation, the achieved power density is 2.61 kVA/kg, which is 30% higher than that of traditional solutions. The efficiency at the rated power of the back-to-back system is 95.8%.

We model numerically regions of the Canadian continental shelves during successive glacio-eustatic cycles to illustrate past, current and future marine gas hydrate (GH) stability and instability. These models indicated that the marine GH resource has dynamic features and the formation age and resource volumes depend on the dynamics of the ocean-atmosphere system as it responds to both natural (glacial-interglacial) and anthropogenic (climate change) forcing. Our models focus on the interval beginning three million years ago (i.e., Late Pliocene-Holocene). They continue through the current interglacial and they are projected to its anticipated natural end. During the current interglacial the gas hydrate stability zone (GHSZ) thickness in each region responded uniquely as a function of changes in water depth and sea bottom temperature influenced by ocean currents. In general, the GHSZ in the deeper parts of the Pacific and Atlantic margins (≥1316 m) thinned primarily due to increased water bottom temperatures. The GHSZ is highly variable in the shallower settings on the same margins (~400–500 m). On the Pacific Margin shallow GH dissociated completely prior to nine thousand years ago but the effects of subsequent sea level rise reestablished a persistent, thin GHSZ. On the Atlantic Margin Scotian Shelf the warm Gulf Stream caused GHSZ to disappear completely, whereas in shallow water depths offshore Labrador the combination of the cool Labrador Current and sea level rise increased the GHSZ. If future ocean bottom temperatures remain constant, these general characteristics will persist until the current interglacial ends. If the sea bottom warms, possibly in response to global climate change, there could be a significant reduction to complete loss of GH stability, especially on the shallow parts of the continental shelf. The interglacial GH thinning rates constrain rates at which carbon can be transferred between the GH reservoir and the atmosphere-ocean system. Marine GH can destabilize much more quickly than sub-permafrost terrestrial GHs and this combined with the immense marine GH reservoir suggests that GH have the potential to affect the climate-ocean system. Our models show that GH stability reacts quickly to water column pressure effects but slowly to sea bottom temperature changes. Therefore it is likely that marine GH destabilization was rapid and progressive in response to the pressure effects of glacial eustatic sea level fall. This suggests against a catastrophic GH auto-cyclic control on glacial-interglacial climate intervals. It is computationally possible but, unfortunately in no way verifiably, to analyze the interactions and impacts that marine GHs had prior to the current interglacial because of uncertainties in temperature and pressure history constraints. Thus we have the capability, but no confidence that we can contribute currently to questions regarding the relationships among climate, glacio-eustatic sea level fluctuations and marine GH stability without improved local temperature and water column histories. We infer that the possibility for a GH control on climate or oceanic cycles is speculative, but qualitatively contrary to our model results.

The influence of droplet size on exergy destruction rate in flow of highly concentrated oil-in-water emulsions was investigated experimentally in a cone and plate geometry. The oil concentration was fixed at 74.5% by volume. At this dispersed-phase (oil) concentration, two different droplet size emulsions were prepared: fine and coarse emulsions. The fine and coarse emulsions were mixed in different proportions to vary the droplet size distribution. Although the dispersed and matrix phases of the emulsions were Newtonian in nature, the emulsions exhibited a non-Newtonian (shear-thinning) behavior due to the high droplet concentration. The shear stress—shear rate data of the emulsions could be described adequately by a power law model. At low shear rates, the exergy destruction rate per unit volume of emulsion exhibited a minimum at a fine emulsion proportion of 35%. The results from the cone and plate geometry were used to simulate exergy loss in pipeline flow of emulsions. The pumping of emulsions becomes more efficient thermodynamically upon mixing of fine and coarse emulsions provided that the flow regime is maintained to be laminar and that the Reynolds number is kept at a low to moderate value. In the turbulent regime, the exergy loss generally increases upon mixing the fine and coarse emulsions.