• Energy Research
• other engineering and technologies close
• CN close
• US close
• CA close

The vehicle will generate an amount of current while the electric vehicle just starting to regeneratively brake. In order to avoid the impact of high current on the traction battery, a novel electrohydraulic hybrid electric vehicle has been proposed. The main power source is supplied by the electric drive system, and the hydraulic system performs the auxiliary drive system that fully exerts the advantages of the electric drive system and the hydraulic drive system. A proper regenerative braking control strategy is presented, and the control parameters are determined by the fuzzy optimization algorithm. The simulation analysis built the model through the united simulation of AMESim and MATLAB/Simulink. The results illustrated that the optimized control strategy can reduce battery consumption by 1.22% under NEDC-operating conditions.

Accurate predictions of fuel spray behavior and mixture formation in simulations of direct-injection spark-ignition (DISI) engines are fundamental to ensure proper description of all subsequent processes including ignition, combustion, and emissions. In this work, the spray evolution in a single-cylinder optical DISI engine was studied experimentally and numerically with the goal of enabling predictive computational fluid dynamics (CFD) modeling of in-cylinder sprays. The authors explored a wide range of operating conditions characterized by several fuel injection temperatures and engine speeds, using a well-characterized nine-component gasoline surrogate known as PACE-20. The effect of flash boiling and intake crossflow on the spray is discussed, with a focus on evaluating the ability of the spray models to capture highly transient spray behavior. In the experiments, the fuel temperature was varied between 20°C and 80°C, allowing for non-flash- to flash-boiling transition to emerge with enhanced flashing intensity at the highest temperatures. Spray collapse resulted in vapor-rich regions, owing to the locally lower inertia of the fluid. Varying the engine speed from 650 to 1950 rpm promoted increasingly more turbulent in-cylinder crossflow which interacted with the spray during the injection event and resulted in enhanced spray dispersion. The CFD model was able to capture the spray morphology transition at different fuel temperatures and engine speeds adequately. It is shown that the spray breakup model could capture the transitional spray behavior induced by flash boiling atomization and intake flow via proper initialization of the spray cone angle and calibration of the spray models’ constants.

Abstract Building energy performance is often inadequate given design goals. While different types of assessment methods exist, they either do not consider design goals and/or are not general enough to integrate new and innovative energy concepts. Furthermore, existing assessment methods focus mostly on the building and system level while ignoring more detailed data. With the availability and affordability of more detailed measured data, the increased number of measured data points requires a structure to organize these data. This paper presents the Energy Performance Comparison Methodology (EPCM), which enables the identification of performance problems based on a comparison of measured data and simulated data representing design goals. The EPCM is based on an interlinked building object hierarchy that structures the detailed performance data from a spatial and mechanical perspective. This research is developed and tested on multiple case studies that provide real-life context and more generality compared to single case studies.

The diffusivity and solubility of fluorine in solid nickel were determined using the following solid-state electrochemical cells: Co + CoF2| BaF2| Ni | BaF2| Co + CoF2 Co + CoF2| CaF2| BaF2| Ni | BaF2| CaF2| Co + CoF2 In the temperature range 1023 to 1223 K, the diffusion coefficient of fluorine in solid nickel is given by: 1 $$D_F (cm^2 /s) = (2.13_{ - 1.54}^{ + 5.54} ) \times 10^{ - 3} \exp (( - 118,600 \pm 12,000J/mol)/RT)$$ The dissolution of atomic fluorine in solid nickel obeys Sieverts’ law; however, the solubility results showed considerable scatter. In the temperature range 1073 to 1223 K, the mean solubility of fluorine in solid nickel, corresponding to the equilibrium Ni + NiF2, follows the relationship: N -F S (at. pct) = 5.73 x 10-3 exp((10,850 J/mol)/RT)

Abstract The objective of this work is to evaluate the surge characteristics of an axial compressor operating under surge conditions, by using a hybrid BDF/harmonic balance method. During a surge event, a large amount of backflow occurs in the compressor. Consequently, the airflow oscillates along the axial direction at a low frequency, which can considerably damage the compressor. In this paper, a numerical investigation is performed to examine the effects of the system volume and average mass flow on the surge characteristics of a transonic high speed single stage axial compressor (stage 35) designed and evaluated at the NASA Glenn Center. The results show that the oscillation frequency of the airflow in the compressor generally ranges from 14.32–26.04 Hz during surge conditions, and both the system volume and average mass flow considerably influence the surge characteristics. For a constant average mass flow, as the system volume decreases, the oscillation frequency of the airflow in the compressor increases slightly, while the oscillation amplitude of the exit static pressure decreases significantly, and the maximum static pressure at the outlet remains nearly constant. In the case of a constant system volume, with the decrease in the average mass flow, the oscillation frequency of the airflow in the compressor gradually decreases, and the oscillation amplitude of the exit pressure increases significantly. With a further decrease in the average mass flow, the oscillation frequency stabilizes at a certain point and does not change thenceforth. Furthermore, the surge frequency obtained using the numerical method shows a same tendency with the Helmholtz frequency, but there is a considerable difference between them.

This paper examines and optimizes parameters that affect the air cooling of a Lithium-Ion (Li-Ion) battery, used in Electric Vehicles (EVs). A battery pack containing 150 cylindrical type Li-Ion battery cells in a PVC casing is investigated. An equal number of tubes are used in the pack as a medium to cool the battery by using a fan when the vehicle is stationary or with ambient air when in motion. The parameters affecting the air cooling of battery are studied and optimized by considering their practical constraints. The objective function and Number of Transfer Unit (NTU) are developed. Finally, a genetic algorithm method is employed to optimize the decision variables. Analysing the results shows that NTU can be maximized by increasing the diameter of tubes on the battery and keeping the air velocity in a certain range.

Abstract Flow behavior of particles in a two-dimensional spouted bed with a draft tube is studied using a continuous kinetic-friction stresses model. The kinetic stress of particles is predicted from kinetic theory of granular flow, while the friction stress is computed from a model proposed by Johnson et al. (1990) . A stitching function is used to smooth from the rapid shearing viscous regime to the slow shearing plastic regime. The distributions of concentration and velocities of particles are predicted in the spouted bed with a draft tube. Simulated results compare with the vertical velocity of particles ( Zhao et al., 2008 ) measured and in the spout bed with draft plates and solid circulation rate ( Ishikura et al., 2003 ) measured in the spouted bed with a draft tube. The impact of the friction stress of particles on the spout, annulus, fountain and entrancement regions is analyzed in gas–solid spouted bed with a draft tube. Numerical results show that the gas flow rate through the annulus increases with the increase of the entrainment zone. The solids circulation rate decreases with the decrease of inlet gas velocity and the height of the entrainment zone. The effect of spouting gas velocity on distributions of concentration, velocity and particle circulation is discussed.

Abstract In this paper, we present the use of different mathematical models to forecast electricity price under deregulated power. A successful prediction tool of electricity price can help both power producers and consumers plan their bidding strategies. Inspired by that the support vector regression (SVR) model, with the e -insensitive loss function, admits of the residual within the boundary values of e -tube, we propose a hybrid model that combines both SVR and Auto-regressive integrated moving average (ARIMA) models to take advantage of the unique strength of SVR and ARIMA models in nonlinear and linear modeling, which is called SVRARIMA. A nonlinear analysis of the time-series indicates the convenience of nonlinear modeling, the SVR is applied to capture the nonlinear patterns. ARIMA models have been successfully applied in solving the residuals regression estimation problems. The experimental results demonstrate that the model proposed outperforms the existing neural-network approaches, the traditional ARIMA models and other hybrid models based on the root mean square error and mean absolute percentage error.