• Energy Research
• 7. Clean energy close
• 12. Responsible consumption close
• 2. Zero hunger close
• CN close
• US close
• DE close
• IN close

Abstract The oxidation characteristics of several small methyl and ethyl esters with carbon number less than six were investigated in laminar flames. The kinetics of such fuels are subsets of those of larger alkyl esters that are constituents of practical biodiesel fuels. A total of seven fuels, namely methyl formate, methyl acetate, methyl propionate, methyl butanoate, ethyl formate, ethyl acetate, and ethyl propionate were considered. Experiments were conducted at atmospheric pressure, elevated reactant temperatures, and over a wide range of equivalence ratios. Laminar flame speeds were determined in the counterflow configuration in which flow velocities were measured using particle image velocimetry. Several detailed kinetic models were tested against the experimental data, and insight was provided into the high-temperature combustion kinetics of the aforementioned fuels. Based on comparisons between experimental and computed results it became apparent that the chemistry of alkyl-ester combustion chemistry is evolving and much needs to be done in order to derive improved rate constants for a wide range of elementary steps.

Abstract In this work addition of ethanol to high viscosity jatropha methyl ester (JME) through port injection is investigated in order to determine its effect fuel viscosity reduction on diesel engine performance. In addition to viscosity alteration, the impact of ethanol addition on combustion characteristics such as combustion duration, ignition delay and emissions levels from diesel engines fuelled with blends of ethanol, diesel and JME is studied in particular. It is found that blending of oxygenated fuels with diesel modifies the chemical structure and physical properties which again alter the engine operating conditions, combustion parameters and emissions levels. However, the injection of only 5% ethanol through port injection allows for a total of 25% blending of biofuels into diesel yet keeping the fuel characteristics close to that of conventional diesel. However, both experimental and numerical results show that ethanol addition in JME blended diesel results in a slight increase in fuel consumption and thermal efficiency for the same power outputs as that of conventional diesel fuel. Also, the combustion characteristics with ethanol addition include improved maximum in-cylinder peak pressure, cumulative heat release (CHR) rate of heat release (ROHR), in-cylinder peak temperature and combustion duration. Regarding emission characteristics the experimental results show significant reduction in smoke, carbon monoxide (CO) and total hydrocarbon (THC) emissions with extended oxygen mass percentage in the fuel at higher engine loads. However, oxides of nitrogen (NOx) emissions are found to increase at high loads although the common tradeoff between smoke and NOx is found to be more prominent for the oxygenated fuels.

White sweet clover found voluntarily growing on a deep bed of soft coal fly ash was found to contain high concentrations of a number of elements including selenium, bromine, and molybdenum, rubidium, strontium, and others. The clover was harvested and fed as 23.5% of a dry pelleted ration to lambs and pregnant goats for up to 173 days. High concentrations of selenium were found in 11 tissues, blood, goats' milk, and excreta of lambs, goats, and newborn kids. Molybdenum in liver, strontium in bone, and bromine and rubidium in animal tissues were also elevated over those in the corresponding tissues of animals fed an identical ration containing control clover grown on soil. No gross or histologic lesions were present in any of the animals.

Abstract A great deal of heat is wasted in intensive public shower facilities, such as those in schools, barracks and natatoriums, which open up at specified time. It will contribute a lot to energy saving and environmental protection with significant economic benefits to recycle the exhaust heat. In this paper, we propose two different kinds of heat pumps (an electric heat pump and an absorption heat pump) in the heat recovery systems. In both system, the used shower water is drained through a pipe and collected in a gray water pool. When the wastewater reaches certain volume, the heat pump system will begin working and recycling heat. The wastewater is filtered and piped to the heat exchanger to exchange heat with the tap water whose temperature will increase from 12 °C to 25 °C with the wastewater temperature dropping from 30 °C to 17 °C. Then the wastewater is piped to the heat pump evaporator and the tap water is piped to the condenser for farther heating. According to the different characteristics of the electric heat pump and absorption heat pump, we also introduce the processes and control methods of different heat recovery systems in details in this paper. Based on a practical example, this paper analyzes and compares the economic and environmental benefits of three retrofitting schemes, including “exhaust heat recovery using electric heat pump”, “exhaust heat recovery using electric heat pump + gas boiler” and “exhaust heat recovery using direct-fired heat pump”. Then we find out that the heat recovery system using direct-fired absorption heat pump has lower energy consumption, less pollution, lower operating cost, and shorter payback period. And it has a promising practical application.

The battery power state (SOP) is the basic indicator for the Battery management system (BMS) of the battery energy storage system (BESS) to formulate control strategies. Although there have been many studies on state estimation of lithium-ion batteries (LIBs), aging and temperature variation are seldom considered in peak power prediction during the whole life of the battery. To fill this gap, this paper aims to propose an adaptive peak power prediction method for power lithium-ion batteries considering temperature and aging is proposed. First, the Thevenin equivalent circuit model is used to jointly estimate the state of charge (SOC) and SOP of the lithium-ion power battery, and the variable forgetting factor recursive least squares (VFF-RLS) algorithm and extended Kalman filter (EKF) are utilized to identify the battery parameters online. Then, multiple constraint parameters including current, voltage, and SOC were derived, considering the dependence of the polarization resistance of the battery on the battery current. Finally, the verification experiment was carried out with LiFePO4 battery. The experimental results under FUDS operating conditions show that the maximum SOC estimation error is 1.94%. And the power prediction errors at 20%, 50%, and 70% SOC were 5.0%, 8.1% and 4.5%, respectively. Our further work will focus on the joint estimation of battery state to further improve the accuracy.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

ABSTRACTPlant heme oxygenases (HOs) regulate biosynthesis of phytochrome which accounts for photo‐acceptance and ‐morphogenesis. Recent studies have demonstrated that plant HOs also regulate many other physiological processes including response to environmental stimuli. To elucidate the mechanism by which HOs regulate plant adaptation to heavy metal exposure, three novel HOs genes were isolated from rapeseed (Brassica napus) and their expression patterns were analysed. Alignment of deduced protein sequences revealed that the three BnHOs share high identity with their corresponding orthologos (AtHO1‐3) from Arabidopsis. To investigate whether the BnHO regulates plant tolerance to Hg toxicity, we constructed B. napus transgenic plants overexpressing BnHO‐1. Under Hg stress, the transgenic plants had 1.41–1.59 folds higher biomass than the untransformants. However, overexpression of BnHO‐1 resulted in less accumulation of Hg in some lines of transformants than in untransformants. The transgenic plants show lower abundance of reactive oxygen species and attenuated oxidative injury compared with the untransgenic plants. We cloned the promoter sequences of BnHO‐1 from B. napus. Analysis revealed that the 1119 bp fragment contains a conserved Cd responsive element (CdRE) and others responding to multiple environmental stimuli. Transient expression in tobacco leaves showed differential responses to heavy metals (Zn, Cu, Pb, Hg and Cd).

Abstract Pollution control strategies currently in use by electric power systems are reviewed and a new minimum emission dispatch (MED) method is developed. This new method minimizes overall emission levels at an increased cost in large-scale power systems while simultaneously accommodating local pollution level requirements, as well as economic constraints.

Given the considerable scale of distribution networks in urban and rural areas, as well as the lack of management records, adjustments of switches during the distribution system operation are poorly documented. Such deficiency results in the inaccuracy of models stored in the distribution network automation system, and thus misleads the state estimation. With the emergence of information and communication technology, a large number of the feeder and residential smart meter data are accumulated. Such data can help recognize the operation modes of distribution networks by analyzing the relationships between the on/off states of switches and the voltage correlations among buses. However, the limited quantity and quality of the sampling data restrict the implementation of data-driven recognition. In this paper, a physical-probabilistic-network (PPN) model applied for inferring overall operation mode of distribution networks is proposed. Based on which, a belief propagation-based algorithm is proposed for the inference even under situations when there are only partial bus voltages data available. Meanwhile, the required variable for inference can be reduced from the active trail analysis. Experiment results are used to compare its performance with classic methods and to prove its effectiveness and advantages.