• Energy Research
• other engineering and technologies close
• ES close
• BE close
• UA close
• MA close

Abstract New techniques for emissions reduction and energy efficiency are important challenges of the steel industry. Although great advantages have been reached in these fields, there are still new opportunities. One of them is the possible development of systems to recover energy from slags. The recent policies that encourage the use of renewable and alternative energies determine a favorable scenario for the development of new techniques of heat recovering. In this context, this article presents a new heat recuperation system for the slags produced in the factories of Arcelor–Mittal in Asturias (Spain) and study in detail the design of an innovative slags heat exchanger. To adjust its performance and to determine the influence of the geometric and flow design parameters, the heat exchanger has been simulated using numerical analysis software (CFD).

Flare stacks are a key element in the safety of petrochemical and refinery industries; the correct operating conditions thereof must be ensured through a schedule for the periodic reviewing of all parts thereof. Advances in Non-Destructive Testing (NDT) in recent years and the application thereof to this field allow reliable, objective information to be obtained. This article describes and groups together the main applicable NDT techniques, analysing their advantages and disadvantages, updated with the new possibilities offered by unmanned aircraft or drones.

This work evaluates, for the first time, the possibility of producing multifunctional alkali-activated composites combining ultra-low density, low thermal conductivity, high acoustic absorption, and good moisture buffering capacity. The composites were prepared using cork as a lightweight aggregate. This novel material might promote energy savings and tackle the CO2 emissions of the building sector, while simultaneously improve the comfort for inhabitants (e.g. humidity levels regulation and sound pollution reduction). The composites apparent density (as low as 168 kg/m3) and thermal conductivity (as low as 68 mW/m K) are amongst the lowest ever reported for alkali-activated materials (AAM) composites and foams, while their sound absorption ability is comparable to the best performing AAM foams reported to date, but in addition these eco-friendly composites also show good ability to passively adjust the humidity levels inside buildings. The multifunctional properties shown by the cork – AAM composites set them apart from other conventional building materials and might contribute to the global sustainability of the construction sector. Peer Reviewed

The lack of real integration between the different dimensions of sustainability is highlighted in the literature as one of the main hindrances to lessening the environmental risks and impacts of large-scale development projects. This paper discusses a hypothesis concerning the problems of integration between the different dimensions of sustainability in socio-environmental research into such projects. Differences in modes of knowledge production and the relationships of these with prevailing social positions constitute the crux of the argument. Endeavours to improve translational knowledge and mixed research methodologies (seeking the semi-standardization of research processes) are put forward as approaches to overcoming the above-mentioned obstacles.

The paper presents a method for decentralized coordination of inter-regional static stability management. This approach allows for an optimal "central" result using a decentralized coordinated solution procedure. The proposed optimization-based approach achieves system-wide efficiency of inter-regional electricity systems or markets while minimizing the amount of information that needs be exchanged. The solution is obtained by adapting decentralized solution techniques of interior point methods to the static stability problem.

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

AbstractEnhancing the efficiency of the electric vehicle’s powertrain becomes a crucial focus, wherein the control system for the traction motor plays a significant role. This paper presents a novel electric vehicle traction motor control system based on a robust predictive direct torque control approach, an improved version of the conventional DTC, where the traditional switching table and the hysteresis regulators are substituted with a predictive block based on an optimization algorithm. Additionally, a robust predictive speed loop regulator is employed instead of the proportional-integral regulator, which integrates a new cost function with a finite horizon, incorporating integral action into the control law based on a Taylor series expansion. This technique’s primary benefit is its independence from the necessity to measure and observe external disturbances, as well as uncertainties related to parameters. The effectiveness of the suggested system was confirmed through simulation and experimental results under the OPAL-RT platform. The findings indicate that the proposed approach outperforms the conventional method in terms of rejecting disturbances, exhibiting robustness to variations in parameters, and minimizing torque ripple.

The basic requirements for materials of modern fortifications are established and substantiated. It is established that concrete of such structures should have high strength under the influence of static loads and low modulus of deformations. To ensure the required deformability, you must use dampers. A quantitative characteristic of reinforcing steel at dynamic dynamic loads is the dynamic strengthening coefficient, which shows the growth of dynamic strength in comparison with static.