• Energy Research
• 2021-2025close
• 7. Clean energy close
• IR close
• CA close
• FR close

Plot design and harvesting Twelve sampling plots (16 m × 16 m) in three P. deltoides plantations were established based on systematic random design. To minimize edge effects, surrounding rows were not considered during sampling. The age of the stands was 18-20 years old. In each sampling plot, the DBH (diameter at breast height 1.3 m above the ground) of the individual trees was measured with a caliper in two perpendicular directions and the mean DBH determined. Tree height was measured by Haglöf-Vertex IV hypsometer. Based on the DBH and height measurements, 10 DBH classes from 15 to 42 cm (3 cm intervals) were established. The value of each DBH class represented the central value (i.e., class 15 included all DBH from 12.5 to 17.5 cm). In each DBH class, one representative tree was selected and harvested for a total of 10 P. deltoides trees. Measurements of bark percentagesThe stems of harvested trees were marked and cut into 2 m-segments. The mid-length diameter of each segment was measured outside the bark in two perpendicular directions with a caliper to determine the mean diameter. A 5 cm-thick disc was cut from the middle of each segment. A total of 123 discs were obtained and brought to the laboratory. All the discs were arranged into 2-cm wide diameter classes. The value of each disc class represents the central value (i.e., class 20 included all discs whose diameters ranged from 19.5 to 20.5 cm). Bark was separated from the wood using a peeler knife for each disc. Fresh bark and wood were weighted separately, oven-dried at 80 °C until constant weight, and the oven-dry weight measured. The bark percentage of each disc was considered as bark percentage of a 2 m-segment for fresh and dry weight. Finally, the bark percentage of the whole stem in each DBH class was calculated by adding the 2 m-segments. Bark biomass as an energy source has a high economic value. Bark content variations and production helps recognize the potential of this bioenergy source spatially before harvesting. The percentage of fresh and dry bark in Populus deltoides grown under a monoculture system was examined in the temperate region of northern Iran. Diameter at breast height (DBH) and total height data were analyzed based on an initial inventory. Ten sample trees were felled, separated into 2 m-segments, and weighted in the field. A 5-cm-thick disc from each segment was extracted for determining fresh and dry bark percentages. These were statistically significantly different in disc diameter classes and decreased with increasing disc diameters. Bark percentage of the disc classes ranged from 21.8 to 24.4% in small-sized diameters to 8.1‒9.3% in large-sized diameters. The differences between fresh and dry bark percentages depended on water content variations. Allometric power equations were fitted to data of fresh and dry bark percentages and disc diameters as well as DBH. The values of R2 ranged from 0.89 to 0.90. In addition, allometric power equations provided the best fits for relationships between total stem dry biomass, dry bark biomass, and DBH, R2 = 0.986 and 0.979 for the total stem dry biomass and stem dry bark biomass, respectively. The allometric models can be used to estimate bark percentage and bark production of P. deltoides in segments and for the whole stem for a wide range of segment diameters (8‒44 cm) and DBH (15‒45 cm).

L'empreinte carbone des technologies numériques est une préoccupation depuis plusieurs années. Cela concerne principalement la consommation électrique des datacenters; beaucoup de fournisseurs dans le domaine du cloud s'engagent à n'utiliser que des sources d'énergie renouvelables. Cependant, cette approche néglige la phase de fabrication des composants des infrastructures numériques. Nous considérons dans ce travail de recherche la question du dimensionnement des énergies renouvelables pour une infrastructure de type cloud géographiquement distribuée autour de la planète, considérant l'impact carbone à la fois de l'électricité issue du réseau électrique local en fonction de la location de sa production, et de la fabrication des panneaux photovoltaïques et des batteries pour la part renouvelable de l'alimentation des ressources. Nous avons modélisé ce problème de minimisation de l'impact carbone d'une telle infrastructure cloud sous la forme d'un programme linéaire. La solution est le dimensionnement optimal d'une fédération de cloud sur une année complète en fonction des localisations des datacenters, des traces réelles des travaux à exécuter et valeurs d'irradiation solaire heure par heure. Nos résultats montrent une réduction de l'impact carbone de 30% comparés à la même architecture cloud totalement alimentée par des énergies renouvelables et 85% comparés à un modèle qui n'utiliserait qu'une alimentation via le réseau local d'électricité. The carbon footprint of IT technologies has been a significant concern in recent years. This concern mainly focuses on the electricity consumption of data centers; many cloud suppliers commit to using 100% of renewable energy sources. However, this approach neglects the impact of device manufacturing. We consider in this work the question of dimensioning the renewable energy sources of a geographically distributed cloud with considering the carbon impact of both the grid electricity consumption in the considered locations and the manufacturing of solar panels and batteries. We design a linear program to optimize cloud dimensioning over one year, considering worldwide locations for data centers, real-life workload traces, and solar irradiation values. Our results show a carbon footprint reduction of about 30% compared to a cloud fully supplied by solar energy and of 85% compared to the 100% grid electricity model. Données computationnelles ou de simulation: En tenant compte des données en entrée (description de la fédération de centres de données, fichiers de configuration appropriés, conditions météorologiques, etc.), le logiciel est capable de proposer un dimensionnement optimal pour la fédération des datacenters à faible émission de carbone distribuée à l'échelle mondiale : surface des panneaux photovoltaïques et capacité des batteries pour chaque datacenter de la fédération. Des scripts sont disponibles pour mettre en forme les solutions proposées. Simulation or computational data: Considering given inputs (datacenter federation, appropriate configuration files, weather conditions, etc.), the software is able to propose an optimal sizing for the globally distributed low carbon cloud federation: surface area of solar panels, battery capacity for each data center location. . Scripts are available to shape the optimal configuration. Audience: Research, Policy maker UpdatePeriodicity: as needed

Article Abstract To better allocate funds in the new EU research framework programme Horizon Europe, an assessment of current and past efforts is crucial. In this paper we develop and apply a multi-method qualitative and computational approach to provide a catalogue of climate crisis mitigation technologies on the EU level between 2014 and 2020. Using the approach, we observed no public EU-level funding for multiple technologies prioritised by the EU, such as low-carbon production and use of cement and chemicals, electric battery, and a number of industrial decarbonisation processes. We observed a rising trend in the funding of solar power and onshore wind, the adjacent to them power-to-X technology, as well as recycling. At the same time, the shares of funding into fuel cell, biofuel, demand-side energy management, microgrids, and waste management show a decline trend. With note of the exploratory character of the present paper, we propose that the EU Horizon 2020 funding of clean technologies only partially reflected the expectations of key institutionalised EU actors due to the existence of many non-funded prioritised technologies.

Comprehensive and reliable information on anthropogenic sources of greenhouse gas emissions is required to track progress towards keeping warming well below 2°C as agreed upon in the Paris Agreement. Here we provide a dataset on anthropogenic GHG emissions 1970-2019 with a broad country and sector coverage. We build the dataset from recent releases from the “Emissions Database for Global Atmospheric Research” (EDGAR) for CO2 emissions from fossil fuel combustion and industry (FFI), CH4 emissions, N2O emissions, and fluorinated gases and use a well-established fast-track method to extend this dataset from 2018 to 2019. We complement this with information on net CO2 emissions from land use, land-use change and forestry (LULUCF) from three available bookkeeping models.

Nowadays, a large part of energy is provided by steam turbines; thus, increasing the efficiency and improving the steam turbines performance are of special importance. The presence of the liquid phase in the low-pressure stage of the steam turbine can cause energy loss, efficiency drop, and erosion/corrosion problems; therefore, one of the essential issues is to identify wet steam flow and try to reduce condensation loss. In order to decrease the liquid fraction, the drainage groove technique can be applied. The drainage groove sucks the water droplets from the turbine blade surface and drains them into the condenser. In this study, the effect of the drainage groove location on the surface of steam turbine blades has been investigated on the condensation, droplet radius, inlet mass flow, erosion rate, liquid drainage ratio, condensation losses, and total drainage ratio. For modeling the condensing flow, the Eulerian–Eulerian approach has been applied. The results show that the location of the drainage groove affects the groove performance and flow pattern in the turbine blade. In the selected drainage, the liquid drainage ratio, condensation losses, and erosion rate are reduced by 7.6%, 12%, and 88%, respectively, compared with the no-drainage groove case. Also, the total drainage ratio is 7.2% in the selected drainage. The outcomes of the present work have been a major step forward in the techniques having a great influence on the lifetime, repair and maintenance, and the output power of steam power generation facilities.

Abstract Economically harvesting energy from a microbial fuel cell (MFC), increasing its electrical power production, and developing its role as a practical energy supply, needs a low-cost and high-performance design of the MFC compartments. According to this strategy, a novel monolithic membrane electrode assembly (MEA) was fabricated and evaluated as an air–cathode in a single-chamber MFC (SCMFC). The MEA was made of bacterial cellulose (BC), conductive multi-walled carbon nanotubes (CNT), and nano-zycosil (NZ). BC, as a nano-celluloses with oxygen barrier property, can maintain anaerobic conditions for the anode compartment. Binder-less CNT coating on BC avoids costly binders such as poly-tetra fluoro ethylene (PTFE) and Nafion and decreases the MEA charge transfer resistance. NZ, as a very cheap modifier, not only prevents the anolyte leakage but also provides more MEA’s active sites for the oxygen reduction reaction (ORR). The electrochemical performance of the MEA was compared to a PTFE- based gas diffusion electrode (GDE) in the SCMFC. The MEA cell provided a pulse power density of 1790 mW/m2, roughly twice as high as the pulse power density of GDE (920 mW/m2). SCMFC’s internal resistance decreased from 1.84 KΩ (with GDE) to 0.8 KΩ (with MEA). Also, the cell’s columbic efficiency increased from 4.2% (with GDE) to11.7% (with MEA). Additionally, the capacitance of the MEA (65 mF) was much higher than the value for GDE (0.73 mF). Thus, the MEA compared to the GDE showed higher performance in the SCMFC for electricity generation and wastewater treatment at a lower cost.

Cette modélisation présente la partie de contrôle d'une pile à combustible à membrane d'échange de protons (PEMFC). L'objectif du modèle de représenter la chaîne de contrôle de la tension de la PEMFC. Ce modèle est basé sur une représentation macroscopique énergétique (REM) de la pile à combustible, puis conduit à une structure dite de contrôle maximal (SCM). La SCM est une inversion étape par étape de la REM (structure de contrôle basée sur un modèle d'inversion). Le processus de conception de la commande est basé sur une définition explicite du problème. Par exemple, les entrées de réglage, les objectifs du système ou les contraintes sont mises en évidence pour organiser la commande. De plus, le SMC montre les endroits où les capteurs sont nécessaires et où les contrôleurs sont requis. Malheureusement, le SCM n'est qu'une structure de contrôle théorique. Par conséquent, une structure réaliste nécessite certaines simplifications, ce qui conduit à une structure de contrôle dite pratique. This modeling presents the control part of a proton exchange membrane fuel cell (PEMFC). The objective of the model is to represent the voltage control chain of the PEMFC. This model is based on an energetic macroscopic representation (EMR) of the fuel cell and then leads to a so-called maximum control structure (MCS). The SCM is a step-by-step inversion of the REM (control structure based on an inversion model). The control design process is based on an explicit problem definition. For example, control inputs, system objectives, or constraints are highlighted to organize the control. In addition, the MSC shows where sensors are needed and where controllers are required. Unfortunately, the SCM is only a theoretical control structure. Therefore, a realistic structure requires some simplifications, which leads to a so-called practical control structure. AdditionnalInformation: Modèle créé lors d'une thèse en génie électrique, par Loïc Boulon (ses recherches portent sur la modélisation et le contrôle des véhicules électriques hybrides, des sources d'énergie et d'énergie et de puissance, et des systèmes de piles à combustible). Il a travaillé en vue de l'obtention du diplôme de doctorat à l'Université de Franche-Comté, Belfort, France, où sa thèse de doctorat a été réalisée en collaboration avec le FEMTO-ST, Belfort, et les Laboratoires L2EP, Lille. Co-encadrement par Daniel Hissel (PU au laboratoire FEMTO-ST), Alain Bouscayrol (PU au laboratoire L2EP) et Marie-Célie Péra (PU au laboratoire FEMTO-ST) AdditionnalInformation: Model created during a thesis in electrical engineering, by Loïc Boulon (his research focuses on the modeling and control of hybrid electric vehicles, energy and power sources, and fuel cell systems). He worked towards his Ph.D. degree at the University of Franche-Comté, Belfort, France, where his dissertation was complet in collaboration with the FEMTO-ST, Belfort, and the L2EP Laboratories, Lille. Co-supervision by Daniel Hissel (PU at FEMTO-ST laboratory), Alain Bouscayrol (PU at L2EP laboratory) and Marie-Célie Péra (PU at FEMTO-ST laboratory) Données computationnelles ou de simulation: - Langage de programmation : Langage Matlab - Plate-forme/OS : Microsoft Windows, Mac OS, Linux,... - Version : MATLAB R2018a - Statut de développement : Actif Simulation or computational data: - Programming language: Matlab language - Platform/OS: Microsoft Windows, Mac OS, Linux,... - Version: MATLAB R2018a - Development status: Active Project: Thèse de doctorat en génie électrique - Loïc Boulon, Contrat doctoral (Region Bourgogne Franche-Comté) Label: PHE (Plateforme Hydrogène-Energie) Audience: Research

AbstractThe integration of power plants and desalination systems has attracted increasing attention over the past few years as an effective solution to tackle sustainable development and climate change issues. In this light, this paper introduces a novel modelling and optimization approach for a combined-cycle power plant (CCPP) integrated with reverse osmosis (RO) and multi-effect distillation (MED) desalination systems. The integrated CCPP and RO–MED desalination system is thermodynamically modelled utilizing MATLAB and EES software environments, and the results are validated via Thermoflex software simulations. Comprehensive energy, exergic, exergoeconomic, and exergoenvironmental (4E) analyses are performed to assess the performance of the integrated system. Furthermore, a new multi-objective water cycle algorithm (MOWCA) is implemented to optimize the main performance parameters of the integrated system. Finally, a real-world case study is performed based on Iran's Shahid Salimi Neka power plant. The results reveal that the system exergy efficiency is increased from 8.4 to 51.1% through the proposed MOWCA approach, and the energy and freshwater costs are reduced by 8.4% and 29.4%, respectively. The latter results correspond to an environmental impact reduction of 14.2% and 33.5%. Hence, the objective functions are improved from all exergic, exergoeconomic, and exergoenvironmental perspectives, proving the approach to be a valuable tool towards implementing more sustainable combined power plants and desalination systems.

This article proposes an effective evolutionary hybrid optimization method for identifying unknown parameters in photovoltaic (PV) models based on the northern goshawk optimization algorithm (NGO) and pattern search (PS). The chaotic sequence is used to improve the exploration capability of the NGO algorithm technique while evading premature convergence. The suggested hybrid algorithm, chaotic northern goshawk, and pattern search (CNGPS), takes advantage of the chaotic NGO algorithm’s effective global search capability as well as the pattern search method’s powerful local search capability. The effectiveness of the recommended CNGPS algorithm is verified through the use of mathematical test functions, and its results are contrasted with those of a conventional NGO and other effective optimization methods. The CNGPS is then used to extract the PV parameters, and the parameter identification is defined as an objective function to be minimized based on the difference between the estimated and experimental data. The usefulness of the CNGPS for extraction parameters is evaluated using three distinct PV models: SDM, DDM, and TDM. The numerical investigates illustrate that the new algorithm may produce better optimum solutions and outperform previous approaches in the literature. The simulation results display that the novel optimization method achieves the lowest root mean square error and obtains better optima than existing methods in various solar cells.

Three distinct dataset used to forecast the development of marine energy in Europe in the upcoming three decades: - European offshore wind farms - tidal energy converter deployements in Europe - wave energy converter deployements in Europe