• Energy Research
• Closed Access close
• Restricted close
• Open Source close
• Embargo close
• US close
• IN close
• GB close
• FR close

Impulsive stress in repeated shock waves administered during extracorporeal shock-wave lithotripsy (ESWL) causes injury to kidney tissue. In a study of the mechanical input of ESWL, the effects of focused shock waves on thin planar polymeric membranes immersed in a variety of tissue-mimicking fluids have been examined. A direct mechanism of failure by shock compression and an indirect mechanism by bubble collapse have been observed. Thin membranes are easily damaged by bubble collapse. After propagating through cavitation-free acoustically heterogeneous media (liquids mixed with hollow glass spheres, and tissue) shock waves cause membranes to fail in fatigue by a shearing mechanism. As is characteristic of dynamic fatigue, the failure stress increases with strain rate, determined by the amplitude and rise time of the attenuated shock wave. Shocks with large amplitude and short rise time (i.e., in uniform media) cause no damage. Thus the inhomogeneity of tissue is likely to contribute to injury in ESWL. A definition of dose is proposed which yields a criterion for damage based on measurable shock wave properties.

Abstract The reverse flat-plate collector is a non-concentrating collector. It can collect solar heat at high temperatures which cannot be achieved by conventional non-concentrating collectors. In this paper, the authors have proposed a number of modified versions of the originally proposed reverse flat-plate collector. The new designs are of single, as well as double, absorber type. The thermal performance of these modified reverse flat-plate collectors is compared with that of a single absorber reverse flat-plate collector, as well as with the corresponding normal flat-plate collector. It is found that the new design having two absorbers gives the best thermal performance as compared with other configurations. The analytical models presented in this paper very well describe the experimental results.

Abstract The analysis and optimization of flat plate fins of constant thickness and straight base has been conducted for different fin’s shapes. Performance of the fins is quantified through effectiveness and expressed as a function of fin’s shape, width, and area. A linear piecewise function with varying number of evenly spaced sections is used to generate shapes with different number of degrees of freedom, which are classified as constrained- or unconstrained-base depending on the width of the fin at the constant temperature base location. For one- and two-degrees of freedom shapes, a variety of rectangular, triangular, trapezoidal, and rhomboidal geometries are considered and optimized. For more than two-degrees of freedom, more complex resulting shapes are also considered. By adjusting the value of the corresponding shape parameters, the best possible distributions of available area to maximize heat transfer are obtained, which produce significant improvements favored by smaller width and larger area. Unconstrained-base performs better than constrained-base configurations as they allow the distribution of a larger area close to the high-temperature base. Optimal shape of unconstrained-base fins is in general convergent with non-zero wide tip, while, for constrained-base fins, it is divergent in the first linear section from the base and convergent in the remaining ones. For increasing number of degrees of freedom the optimized shapes tend to resemble natural structures while effectiveness increases asymptotically to a limit for constant width and area. Besides determining the optimal configurations, consideration has been made about the optimal regions where a variety of shapes produce virtually the same effectiveness of the absolute maximum, which can be used to design fins with almost maximum performance but having simpler shapes or being functional under possible space restrictions. The dimensionless model and the systematic analysis proposed in this work are not only appropriate to study a wide range of flat plate fins but also can be implemented to analyze and perform optimization over other type of fins and fins configurations.

Abstract Dimethyl ether appears to be a better choice among various diesel alternatives due to its high cetane number and sootless combustion. However, the physical and chemical properties of dimethyl ether are very different from those of diesel. The physical properties influence spray formation and atomization characteristics, while chemical properties determine combustion and emission formation characteristics. Thus, fuel's physical and chemical properties significantly determine engine performance and emissions. In the present work, spray combustion and emission formation characteristics of n-heptane, dimethyl ether, and their blends (10, 25, and 50% dimethyl ether in n-heptane) were numerically studied in a constant volume chamber. Results show that the n-heptane spray combustion has the highest heat release rate with an intense premix combustion phase, whereas dimethyl ether spray combustion has the lowest heat release rate and shortest premix combustion phase. The magnitude of the premixed phase and heat release rate decreases with the increase in dimethyl ether mass fraction in the blends. Soot, carbon monoxide (CO), unburned hydrocarbon (UHC), and nitric oxide (NO) emissions decreased with the increase in the dimethyl ether mass fraction in the blends and were lowest for the dimethyl ether.

Abstract In this work addition of ethanol to high viscosity jatropha methyl ester (JME) through port injection is investigated in order to determine its effect fuel viscosity reduction on diesel engine performance. In addition to viscosity alteration, the impact of ethanol addition on combustion characteristics such as combustion duration, ignition delay and emissions levels from diesel engines fuelled with blends of ethanol, diesel and JME is studied in particular. It is found that blending of oxygenated fuels with diesel modifies the chemical structure and physical properties which again alter the engine operating conditions, combustion parameters and emissions levels. However, the injection of only 5% ethanol through port injection allows for a total of 25% blending of biofuels into diesel yet keeping the fuel characteristics close to that of conventional diesel. However, both experimental and numerical results show that ethanol addition in JME blended diesel results in a slight increase in fuel consumption and thermal efficiency for the same power outputs as that of conventional diesel fuel. Also, the combustion characteristics with ethanol addition include improved maximum in-cylinder peak pressure, cumulative heat release (CHR) rate of heat release (ROHR), in-cylinder peak temperature and combustion duration. Regarding emission characteristics the experimental results show significant reduction in smoke, carbon monoxide (CO) and total hydrocarbon (THC) emissions with extended oxygen mass percentage in the fuel at higher engine loads. However, oxides of nitrogen (NOx) emissions are found to increase at high loads although the common tradeoff between smoke and NOx is found to be more prominent for the oxygenated fuels.

Abstract Additional experimental data concerning the kinetics of Ni-Mo codeposition were obtained by investigating cathodic polarization using a rotating disc electrode. The Ni-Mo alloys were deposited from an ammonium citrate bath. The alloy deposition was controlled by activation in the case of low values of the cathode potential and by diffusion in the case of higher values. The hydrogen discharge was found to be diffusion controlled. The inductive influence of nickel results in depolarization of the reduction of molybdenum which cannot be deposited separately. An increase in the disc rotation speed caused an increase in the maximum cathode efficiency and in the molybdenum content of the alloy.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

Abstract Pollution control strategies currently in use by electric power systems are reviewed and a new minimum emission dispatch (MED) method is developed. This new method minimizes overall emission levels at an increased cost in large-scale power systems while simultaneously accommodating local pollution level requirements, as well as economic constraints.