• Energy Research
• 2021-2025close
• 7. Clean energy close
• 13. Climate action close
• 12. Responsible consumption close
• GB close
• DE close

Climate change is a global problem, which affects the various geographical regions at different levels. It is also associated with a wide range of human health problems, which pose a burden to health systems, especially in regions such as Africa. Indeed, across the African continent public health systems are under severe pressure, partly due to their fragile socioeconomic conditions. This paper reports on a cross-sectional study in six African countries (Ghana, Nigeria, South Africa, Namibia, Ethiopia, and Kenya) aimed at assessing their vulnerabilities to climate change, focusing on its impacts on human health. The study evaluated the levels of information, knowledge, and perceptions of public health professionals. It also examined the health systems’ preparedness to cope with these health hazards, the available resources, and those needed to build resilience to the country’s vulnerable population, as perceived by health professionals. The results revealed that 63.1% of the total respondents reported that climate change had been extensively experienced in the past years, while 32% claimed that the sampled countries had experienced them to some extent. Nigerian respondents recorded the highest levels (67.7%), followed by Kenya with 66.6%. South Africa had the lowest level of impact as perceived by the respondents (50.0%) when compared with the other sampled countries. All respondents from Ghana and Namibia reported that health problems caused by climate change are common in the two countries. As perceived by the health professionals, the inadequate resources reiterate the need for infrastructural resources, medical equipment, emergency response resources, and technical support. The study’s recommendations include the need to improve current policies at all levels (i.e., national, regional, and local) on climate change and public health and to strengthen health professionals’ skills. Improving the basic knowledge of health institutions to better respond to a changing climate is also recommended. The study provides valuable insights which may be helpful to other nations in Sub-Saharan Africa.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

Abstract Subcooled flow boiling is frequently encountered in hot assemblies in nuclear power plant. Considerable efforts have been made to improve the understanding of boiling process and prediction of critical heat flux (CHF). In this study, the effects of non-uniform heat input on heat transfer characteristics are further investigated, so that more realistic descriptions of practical systems can be achieved vis-a-vis usual heat input assumptions. A CFD model has been built to predict subcooled flow boiling process in a vertical round pipe. The capability of the model is validated against experimental results in the publication. A variety of non-uniform heat input profiles are tested using this validated CFD model. Results show that a regular triangle-shape heat input profile will cause stronger vapour generation in the middle of the heating region. Also, the risk of reaching CHF may be increased with the position of maximum heat flux moving downstream.

The decarbonisation of heating in the United Kingdom is likely to entail both the mass adoption of heat pumps and widespread development of district heating infrastructure. Estimation of the spatially disaggregated heat demand is needed for both electrical distribution network with electrified heating and for the development of district heating. The temporal variation of heat demand is important when considering the operation of district heating, thermal energy storage and electrical grid storage. The difference between the national and urban heat demands profiles will vary due to the type and occupancy of buildings leading to temporal variations which have not been widely surveyed. This paper develops a high-resolution spatiotemporal heat load model for Great Britain (GB: England, Scotland a Wales) by identifying the appropriate datasets, archetype segmentation and characterisation for the domestic and nondomestic building stock. This is applied to a thermal model and calibrated on the local scale using gas consumption statistics. The annual GB heat demand was in close agreement with other estimates and the peak demand was 219 GWth. The urban heat demand was found to have a lower peak to trough ratio than the average national demand profile. This will have important implications for the uptake of heating technologies and design of district heating.

AbstractSolar fuels offer a promising approach to provide sustainable fuels by harnessing sunlight1,2. Following a decade of advancement, Cu2O photocathodes are capable of delivering a performance comparable to that of photoelectrodes with established photovoltaic materials3–5. However, considerable bulk charge carrier recombination that is poorly understood still limits further advances in performance6. Here we demonstrate performance of Cu2O photocathodes beyond the state-of-the-art by exploiting a new conceptual understanding of carrier recombination and transport in single-crystal Cu2O thin films. Using ambient liquid-phase epitaxy, we present a new method to grow single-crystal Cu2O samples with three crystal orientations. Broadband femtosecond transient reflection spectroscopy measurements were used to quantify anisotropic optoelectronic properties, through which the carrier mobility along the [111] direction was found to be an order of magnitude higher than those along other orientations. Driven by these findings, we developed a polycrystalline Cu2O photocathode with an extraordinarily pure (111) orientation and (111) terminating facets using a simple and low-cost method, which delivers 7 mA cm−2 current density (more than 70% improvement compared to that of state-of-the-art electrodeposited devices) at 0.5 V versus a reversible hydrogen electrode under air mass 1.5 G illumination, and stable operation over at least 120 h.

The construction industry is considered as one of the least productive, highest energy consuming, and least digitized industries. The Lean Management (LM) philosophy became a significant way for eliminating non-value-added activities and wastes during a building’s lifecycle. However, studies have shown that philosophies are not efficient by themselves to solve the issues of the construction industry. They need to be supported with the appropriate technologies and tools. Therefore, the integrated use of Building Information Modelling (BIM) with LM or Value Engineering (VE) were proposed in the literature. Nonetheless, it was also seen that BIM can provide more insights and improvements when BIM is integrated with data analysis tools to analyze BIM data. In the literature, the synergies between these concepts are generally addressed pairwise, and there is no comprehensive framework which identifies their relationships. Therefore, this study aims to develop a maturity framework that facilitates the adoption of LM, VE, BIM, and Big Data Analytic (BDA) concepts to address long-standing productivity and digitalization issues in the Architecture, Engineering, and Construction (AEC) industry. Design Science Research (DSR) methodology and its three-cycle view (relevance, rigor, and design cycle) were applied to build the proposed maturity framework. Two interviews were performed to identify and observe research problem in relevance cycle. In the rigor cycle, a comprehensive literature review was performed to create a base for the development of the maturity framework. In addition to the developed base of the framework, lean processes were added to this cycle. In the design cycle, the developed framework was evaluated and validated by five experts through face-to-face interviews. The importance of employer’s requirements to adopt the proposed methodologies, the negative impact of change orders, the importance of pre-construction phases to facilitate value creation and waste elimination, and the usage of common data environment with BIM were identified as the prominent application and adaptation issues.