• Energy Research
• 6. Clean water close
• GB close
• ES close
• AU close
• CL close
• Energies close

This review article addresses wastewater treatment methods in the red meat processing industry. The focus is on conventional chemicals currently in use for abattoir wastewater treatment and energy related aspects. In addition, this article discusses the use of cleaning and sanitizing agents at the meat processing facilities and their effect on decision making in regard to selecting the treatment methods. This study shows that cleaning chemicals are currently used at a concentration of 2% to 3% which will further be diluted with the bulk wastewater. For example, for an abattoir that produces 3500 m3/day wastewater and uses around 200 L (3%) acid and alkaline chemicals, the final concentration of these chemical will be around 0.00017%. For this reason, the effects of these chemicals on the treatment method and the environment are very limited. Chemical treatment is highly efficient in removing soluble and colloidal particles from the red meat processing industry wastewater. Actually, it is shown that, if chemical treatment has been applied, then biological treatment can only be included for the treatment of the solid waste by-product and/or for production of bioenergy. Chemical treatment is recommended in all cases and especially when the wastewater is required to be reused or released to water streams. This study also shows that energy consumption for chemical treatment units is insignificant while efficient compared to other physical or biological units. A combination of a main (ferric chloride) and an aid coagulant has shown to be efficient and cost-effective in treating abattoir wastewater. The cost of using this combination per cubic meter wastewater treated is 0.055 USD/m3 compared to 0.11 USD/m3 for alum and the amount of sludge produced is 77% less than that produced by alum. In addition, the residues of these chemicals in the wastewater and the sludge have a positive or no impact on biological processes. Energy consumption from a small wastewater treatment plant (WWTP) installed to recycle wastewater for a meet facility can be around $500,000.

Groundwater pumping systems using photovoltaic (PV) energy are increasingly being implemented around the world and, to a greater extent, in rural and electrically isolated areas. Over time, the cost of these systems has decreased, providing greater accessibility to freshwater in areas far from urban centers and power grids. This paper proposes a novel sustainability analysis of the groundwater pumping systems in Tenerife Island as an example of a medium-size isolated system, analyzing the current status and the business-as-usual projection to 2030, considering the water reservoirs available and the final use of water. The 2030 projection focused on the PV deployment, evaluation of the levelized cost of electricity (LCOE), and the availability of the groundwater resource. HOMER software was used to analyze the LCOE, and ArcGIS software was used for the visual modeling of water resources. As a result, the average LCOE for a purely PV installation supplying electricity to a pumping system in Tenerife is 0.2430 €/kWh, but the location and characteristic of each pumping system directly affect the performance and costs, mostly due to the solar availability.

This study analyzes a buffer tank simulated in both continuous operation mode and heating mode using CFD techniques. The analysis is focused in the thermal behavior of the tank, especially in parameters such as heat exchanged, heating time, and temperature distributions into the tank, in order to propose a better design. The results of the different simulations show that the tank heats water extremely slowly and extremely evenly when producing domestic hot water (DHW), which negatively affects the thermal stratification that is critical for rapidly reaching the DHW temperature. Therefore, the main problem of the tank is an inefficient heat exchange and a poor distribution of temperature. In order to overcome these operational limitations, a new design is proposed by installing a tube inside the tank that encloses the heating coil and sends hot water directly to the tank top region such that high-temperature DHW is rapidly provided, and thermal stratification is improved. Several simulations are performed with different open and closed configurations for the outlets of the inner tube. The different results show that the heating times significantly improve, and the time needed to reach the 45 °C set point temperature is reduced from 44 to 15 min. In addition, the simulations in which the opening and closing of the water outlets are regulated, the outlet DHW temperature is kept within 45–60 °C, which prevents overheating to unsafe use temperatures. Furthermore, the results of the simulation in continuous operation mode show a clear improvement of thermal stratification and an increase in the heat transmitted to the inside of the tank.

Innovative toilets can save resources, but have higher embodied impacts associated with materials and electronic components. This article presents an environmental life-cycle assessment (LCA) of an innovative multifunctional toilet (WashOne) for two alternative configurations (with or without washlet), comparing its performance with those of conventional systems (toilet and bidet). Additionally, two scenario analyses were conducted: (i) user behavior (alternative washlet use patterns) and (ii) user location (Portugal, Germany, the Netherlands, Sweden and Saudi Arabia). The results show that the WashOne with washlet has a better global environmental performance than the conventional system, even for low use. It also reveals that the use phase has the highest contribution to impacts due to electricity consumption. User location analysis further shows that Sweden has the lowest environmental impact, while Germany and the Netherlands have the highest potential for impact reduction when changing from a conventional system to the WashOne. Based on the overall results, some recommendations are provided to enhance the environmental performance of innovative toilet systems, namely the optimization of the washlet use patterns. This article highlights the importance of performing a LCA at an early stage of the development of innovative toilets by identifying the critical issues and hotspots to improve their design and performance.

This paper presents an analytical investigation of heat-transfer limits of a novel solar loop-heat pipe developed for space heating and domestic hot water use. In the loop-heat pipe, the condensate liquid returns to the evaporator via small specially designed holes, using a mini-channel evaporator. The study considered the commonly known heat-transfer limits of loop-heat pipes, namely, the viscous, sonic, entrainment, boiling and heat-transfer limits due to the two-phase pressure drop in the loop. The analysis considered the main factors that affect the limits in the mini-channel evaporator: the operating temperature, mini-channel aspect ratio, evaporator length, evaporator inclination angle, evaporator-to-condenser height difference and the dimension of the holes. It was found that the entrainment is the main governing limit of the system operation. With the specified loop design and operational conditions, the solar loop-heat pipe can achieve a heat-transport capacity of 725 W. The analytical model presented in this study can be used to optimise the heat-transfer capacity of the novel solar loop-heat pipe.

Almost all countries have committed to develop Nationally Determined Contributions (NDC) to reduce GHG emissions. They determine the level of GHG mitigation that, as a nation, they will commit to reducing. Zimbabwe has ambitious and laudable GHG mitigation targets. Compared to a coal-based future, emissions will be reduced by 33% per capita by 2030. If historical climate conditions continue, it can do this at low or negative cost if suitable sources of climate financing are in place. The NDC plots a positive future. However, much of Zimbabwe’s NDC mitigation center on hydropower generation and other measures that are dangerously vulnerable to climate change. Should the climate change in accordance with recent projections, these investments will be at risk, severely constraining electricity supply and causing high degrees of economic damage. This paper uses the Open-Source energy Modelling SYStem (OSeMOSYS) to consider two adaptation pathways that address this vulnerability. In the first, the country turns to a historically accessible option, namely the deployment of coal. In so doing, the electrical system is made more resilient, but emissions ramp up. The second pathway ‘climate proofs’ the power sector by boosting solar and wind capacity, using hydropower to provide balance for these new renewable resources, and introducing significant energy efficiency measures. This second pathway would require a set of extra accompanying investments and changes to the power market rules, but allows for both system resilience and NDC targets to be met. The paper shows that Zimbabwe’s low emissions growth can be made resilient, and while this path promises strong benefits, it also requires strong commitment and political will. From this paper insights are drawn and requirements for future analysis are made. Two critical insights are that: (i) NDCs that focus on mitigation should include resilience in their design. If they do not, they can introduce deep vulnerability; (ii) a departure from historical electricity market structures appears to hold potential for strong environmental, cost and reliability gains.

The water distribution system has deployed several low-power IoT devices on an uneven surface where battery power is a major concern. Therefore, this paper focuses on using a UAV-enabled wireless powered communication network capable of directing energy to a target location and using it for communication, thereby reducing battery issues. In this paper, a static optimization was applied to find the initial height values using 3D clustering and beamforming method and dynamic optimization using extremum seeking method was applied to find the optimized height. The optimized height values were calculated and Travelling Salesman Problem (TSP) was applied to create the trajectory of the UAV. The overall energy consumption of the UAV was minimized by integrating dynamic optimization and dome packing method, which can find an optimal position and trajectory where the UAV will be hovering to direct energy and collect data. Moreover, we also minimized the total flight time of the UAV.