• Energy Research
• engineering and technology close
• GB close
• IT close
• AU close

AbstractThis work reports the synthesis, characterization, photophysical, and photovoltaic properties of five new thieno[3,2‐b][1]benzothiophene isoindigo (TBTI)‐containing low bandgap donor–acceptor conjugated polymers with a series of comonomers and different side chains. When TBTI is combined with different electron‐rich moieties, even small structural variations can have significant impact on thin film morphology of the polymer:phenyl C70 butyric acid methyl ester (PCBM) blends. More importantly, high‐resolution electron energy loss spectroscopy is used to investigate the phase‐separated bulk heterojunction domains, which can be accurately and precisely resolved, enabling an enhanced correlation between polymer chemical structure, photovoltaic device performance, and morphology.

Abstract The consumption of takeaway food is increasing worldwide. Single-use containers used for takeaway food represent a significant source of waste and environmental impacts due to their low recyclability. Consequently, it is important to identify the best available alternatives and improvement opportunities to reduce the environmental impacts of fast-food containers. For these purposes, this study estimates and compares for the first time the life cycle impacts of three most widely-used types of takeaway container: aluminium, polypropylene and extruded polystyrene. These are also compared to reusable polypropylene containers. The findings suggest that single-use polypropylene containers are the worst option for seven out of 12 impacts considered, including global warming potential. They are followed by the aluminium alternative with five highest impacts, including depletion of ozone layer and human toxicity. Overall, extruded polystyrene containers have the lowest impacts due to the lower material and electricity requirements in their manufacture. They are also the best option when compared to reused takeaway polypropylene containers, unless the latter are reused 3–39 times. The number of uses needed for the reusable “Tupperware” polypropylene food savers is even higher, ranging from 16 to 208 times, with terrestrial ecotoxicity being always higher than for extruded polystyrene, regardless of the number of uses. However, extruded polystyrene containers are currently not recycled and cannot be considered a sustainable option. If they were recycled in accordance with the European Union 2025 policy on waste packaging, most of their impacts would be reduced by >18%, while also reducing littering and negative effects on marine organisms. Most of the impacts of the other two types of container would also be reduced (>20%) through increased recycling. Implementing the European Union 2025 policy on recycling of waste packaging would reduce all the impacts by 2%–60%, including a 33% reduction in global warming potential. Based on 2025 million takeaway containers used annually in the European Union, the latter would save 61,700 t CO2 eq./yr, equivalent to the emissions of 55,000 light-duty vehicles. The outcomes of this study will be of interest to packaging manufacturers, food outlets, policy makers and consumers.

The successful electricity grid integration of solar energy into day-ahead markets requires at least hourly resolved 48 h forecasts. Technologies as photovoltaics and non-concentrating solar thermal technologies make use of global horizontal irradiance (GHI) forecasts, while all concentrating technologies both from the photovoltaic and the thermal sector require direct normal irradiances (DNI). The European Centre for Medium-Range Weather Forecasts (ECMWF) has recently changed towards providing direct as well as global irradiances. Additionally, the MACC (Monitoring Atmospheric Composition & Climate) near-real time services provide daily analysis and forecasts of aerosol properties in preparation of the upcoming European Copernicus programme. The operational ECMWF/IFS (Integrated Forecast System) forecast system will in the medium term profit from the Copernicus service aerosol forecasts. Therefore, within the MACC‑II project specific experiment runs were performed allowing for the assessment of the performance gain of these potential future capabilities. Also the potential impact of providing forecasts with hourly output resolution compared to three-hourly resolved forecasts is investigated. The inclusion of the new aerosol climatology in October 2003 improved both the GHI and DNI forecasts remarkably, while the change towards a new radiation scheme in 2007 only had minor and partly even unfavourable impacts on the performance indicators. For GHI, larger RMSE (root mean square error) values are found for broken/overcast conditions than for scattered cloud fields. For DNI, the findings are opposite with larger RMSE values for scattered clouds compared to overcast/broken cloud situations. The introduction of direct irradiances as an output parameter in the operational IFS version has not resulted in a general performance improvement with respect to biases and RMSE compared to the widely used Skartveit et al. (1998) global to direct irradiance conversion scheme. Cloudy situations and especially thin ice cloud cases are forecasted much better with respect to biases and RMSE, but large biases are introduced in clear sky cases. When applying the MACC aerosol scheme to include aerosol direct effects, an improvement especially in DNI biases is found for cloud free cases as expected. However, a performance decrease is found for water cloud cases. It is assumed that this is caused by the lack of an explicit modelling of cloud-aerosol interactions, while other meteorological forcings for cloud processes like the temperature field are modified by the aerosols.

Abstract Ti-doped ZnO (ZnO/Ti) thin films were grown on indium tin oxide substrates by a facile electrodeposition route. The morphology, crystal structure and resistive switching properties were examined, respectively. The morphology reveals that grains are composed of small crystals. The (002) preferential growth along c-axis of ZnO/Ti could be observed from structural analysis. The XPS study shows the presence of oxygen vacancies in the prepared films. Typical bipolar and reversible resistance switching effects were observed. High R OFF/R ON ratios (approximately 14) and low operation voltages within 100 switching cycles are obtained. The filament theory and the interface effect are suggested to be responsible for the resistive switching phenomenon.

Microgrids are increasingly being used as a platform to integrate distributed generation such as renewable energy sources and (RESs) conventional sources in both grid-connected and isolated power systems. Due to the inherent intermittent nature of RESs, energy storage systems (ESSs) that can absorb fluctuations have become inevitable. Nevertheless, large capacities of ESSs increase the initial cost while small capacities lead to instabilities and increase in the cost of conventional fuels. Therefore, finding the optimal size of the ESS for a given application is essential for the reliable, efficient and economical operation of a microgrid. Once the battery size is decided, maintaining its energy at appropriate levels is essential to ensure stable and safe operation of the microgrid. This paper presents a novel expert fuzzy system - grey wolf optimization (FL-GWO) based intelligent meta-heuristic method for battery sizing and energy management. The proposed energy management operation is carried out by a Grey Wolf Optimiser (GWO) that is helped to set the membership functions and rules of the fuzzy logic expert system. The unit commitment (UC) issue, which is essential for the proper operation of the isolated microgrid, has been additionally considered in this paper. To verify the performance of the proposed method, results are compared with the rules-based method and traditional GWO algorithm. It has been proven from the results that the FL-GWO has a significant convergence property and capability to minimize the Levelized Cost Of Electricity (LCOE) by 14.13% and 24.15% compared with conventional GWO algorithm and rules-based method, respectively. The weather conditions for different climates is used to verify the performance of the intelligent energy management method under different operating scenarios. The results show that the intelligent online multi-objective energy management strategy is capable of managing a smooth power flow with the same optimal configuration in the isolated microgrid, minimising the fossil fuel utilisation and reducing the CO2 emission level.

A new sizing approach is applied in this paper to stand-alone PV systems design, which is based on systems configurations without shedding load. The investigation is based on a detailed study of the minimum storage requirement and an analysis of the sizing curves. The analysis reveals the importance of using daily series of measured solar radiation data instead of monthly average values. For high-reliability systems, it is important that these data series are as long as possible, while the configuration of large generator and small battery seems to deal better with the unpredictability of solar radiation.

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.