• Energy Research
• engineering and technology close
• GB close
• PT close
• AO close

ABSTRACTThe California generation fleet manages the existing variability and uncertainty in the demand for electric power (load). When wind power is added, the dispatchable generators manage the variability and uncertainty of the net load (load minus wind power). The variability and uncertainty of the load and the net load are compared when 8790 MW of wind power are added to the California power system, a level expected when California achieves its 33% renewable portfolio standard, using a data set of 26,296 h of synchronous historic load and modeled historic wind power output. Variability was calculated as the rate of change in power generated by wind farms or consumed by the load from 1 h to the next (MW/h). Uncertainty was calculated as the 1 h ahead forecast error [MW] of the wind power or of the load. The data show that wind power adds no additional variability than is already present in the load variability. However, wind power adds additional uncertainty through increased forecast errors in the net load compared with the load. Forecast errors in the net load increase 18.7% for negative forecast errors (actual less than forecast) and 5.4% for positive forecast errors (actual greater than forecast). The increase in negative forecast errors occurs only during the afternoon hours when negative load forecasts and positive wind forecasts are strongly correlated. Managing the integration of wind power in the California power system should focus on reducing wind power forecast uncertainty for wind ramp ups during the afternoon hours. Copyright © 2013 John Wiley & Sons, Ltd.

In this paper, we investigate the energy harvesting (EH) technique and accordingly design transceivers for a $K$ link multiple-input multiple-output interference channel. Each link consists of two full-duplex (FD) Internet of Things (IoT) nodes exchanging information simultaneously in a bi-directional communication channel. All the nodes suffer from interference, in particular strong self-interference and inter-node interference, due to operating in FD mode and simultaneous transmission at each link, respectively. Further, we divide the received signal at each node into two parts. While one part of the signal is used for information decoding, the other part is used for EH. We jointly design the transmit and receive beamforming vectors and receiver power splitting ratios by minimizing the total transmission power of the system, subject to both signal-to-interference-plus-noise ratio and EH threshold constraints. Furthermore, the case of multiple-input single-output interference channel is also included for the sake of comparison. We also revisit the above problems for the case when the available channel state information (CSI) at the transmitters is imperfect, where the errors of the CSI are assumed to be norm bounded. Simulation results show that the EH technique can harvest enough energy to support power consumption limited IoT devices by aiding in recharging their respective batteries.

For zero‐defect wave soldering of double‐sided and multilayer printed circuit boards, the copper through‐hole‐plating must be impervious to gas generated in the laminate for the period of a few seconds while the solder is molten. The kinetics of the gas evolution during soldering have been related quantitatively to the integrity of the plated copper. This in turn is related to the quality of the electroless copper (evaluated using the backlighting test), the nature and distribution of the catalyst (evaluated using X‐ray photoelectron spectroscopy) and the methods and effectiveness of the hole‐wall preparation (evaluated using scanning electron microscopy). The relevance of laboratory measurements has been confirmed on a wide range of industrial production plating lines.

This work evaluates, for the first time, the possibility of producing multifunctional alkali-activated composites combining ultra-low density, low thermal conductivity, high acoustic absorption, and good moisture buffering capacity. The composites were prepared using cork as a lightweight aggregate. This novel material might promote energy savings and tackle the CO2 emissions of the building sector, while simultaneously improve the comfort for inhabitants (e.g. humidity levels regulation and sound pollution reduction). The composites apparent density (as low as 168 kg/m3) and thermal conductivity (as low as 68 mW/m K) are amongst the lowest ever reported for alkali-activated materials (AAM) composites and foams, while their sound absorption ability is comparable to the best performing AAM foams reported to date, but in addition these eco-friendly composites also show good ability to passively adjust the humidity levels inside buildings. The multifunctional properties shown by the cork – AAM composites set them apart from other conventional building materials and might contribute to the global sustainability of the construction sector. Peer Reviewed

The industrial sector accounts for 17% of end-use energy in the UK, and 54% globally. Therefore, there is substantial scope for simulating and assessing potential energy retrofit options for industrial buildings. Building Energy Modelling (BEM) applied to industrial buildings poses a complex but important opportunity for reducing global energy demand, due to years of renovation and expansion. Large and complex industrial buildings make modelling existing geometry for BEM difficult and time consuming. This paper presents a potential solution for quickly capturing and processing as-built geometry of a factory to be utilized in BEM. Laser scans were captured from the interior of an industrial facility to produce a Point Cloud. The existing capabilities of a Point Cloud processing software were assessed to identify the potential development opportunities to automate the conversion of Point Clouds to building geometry for BEM applications. In conclusion, scope exists for increasing the speed of 3D geometry creation of an existing industrial building for application in BEM and subsequent thermal simulation.

Abstract Two office layouts with high and low levels of thermal control were compared, respectively traditional cellular and contemporary open plan offices. The traditional Norwegian practice provided every user with control over a window, blinds, door, and the ability to adjust heating and cooling. Occupants were expected to control their thermal environment to find their own comfort, while air conditioning was operating in the background to ensure the indoor air quality. In contrast, in the British open plan office, limited thermal control was provided through openable windows and blinds only for occupants seated around the perimeter of the building. Centrally operated displacement ventilation was the main thermal control system. Users’ perception of thermal environment was recorded through survey questionnaires, empirical building performance through environmental measurements and thermal control through semi-structured interviews. The Norwegian office had 35% higher user satisfaction and 20% higher user comfort compared to the British open plan office. However, the energy consumption in the British practice was within the benchmark and much lower than the Norwegian office. Overall, a balance between thermal comfort and energy efficiency is required, as either extreme poses difficulties for the other.

Abstract Ammonia-based chemisorption cycle driven by low grade heat exhibits vast potential for power generation because there exists huge pressure difference between the two salt-adsorbent-filled reactors. However, the intrinsic feature of ammonia as a wet fluid and the difficult match between chemisorption cycle and expansion device impede the development of such a power generation system and also increase the difficulty of practical implementation. To explore maximum benefits of this technology, the present work has proposed and studied a new resorption power generation cycle that applies multiple expansion. The application of multiple expansion integrated with reheating processes aims to overcome the limitation of the ammonia being wet fluid and fully harness the huge pressure difference that chemisorption can offer for power generation, leading to the improvement of energy efficiency. The performance of the proposed multiple expansion resorption power generation cycle using three typical resorption salt pairs, including sodium bromide – manganese chloride, strontium chloride – manganese chloride and sodium bromide – strontium chloride, have been investigated not just based on theoretical thermodynamics but also with the consideration of practical factors to obtain better understanding and more insights for a real system design. The multiple expansion resorption power generation using sodium bromide – manganese chloride and sodium bromide – strontium chloride pairs can achieve 100–600 kJ/kg (ammonia) work output when heat source temperature is from 30 °C to 150 °C; the multiple expansion using strontium chloride – manganese chloride pair has higher average work output per one expansion stage than that using the other two pairs. The cyclic energy efficiency can be achieved as 0.06–0.15 when implementing 2–4 expansions in a more practical scenario where the equilibrium pressure drop is set to 2 bar and the heat source temperature is in the range of 80–150 °C. Such efficiencies are circa 27–62% of Carnot efficiency under the same thermal conditions.