• Energy Research
• engineering and technology close
• PL close
• AT close

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

The paper presents an experimental study on the formation process of burden surface texture on the blast furnace throat and its influence on the radial distribution of gas flow. The study was performed with the application of blast furnaces equipped with a bell-type charging device using radio-isotope means for the control of burden surface texture (profile) and burden surface level, i.e., gamma locators for burden surface texture. The study was carried out under the conditions of an operating blast furnace in an iron and steel plant using a unique GEOTAPS system for automated control of geometric and temperature parameters of burden material surface on the blast furnace throat. The influence of the surface texture on the gas flow distribution was also investigated. The possibility of a self-stabilization effect for burden surface texture and gas flow in an operating blast furnace under suitable conditions was experimentally proven. As a result of the experimental study performed, four ways of energy-saving technology implementation were determined for the control of blast furnace melting based on the data on the burden surface texture and previously unknown regularities of surface layer formation of burden material on the throat of an operating blast furnace with a bell-type charging device. The main idea of the paper is the development of automated control for the radial distribution of burden material and gas flow using actual or predicted surface texture parameters as important intermediate factors that both describe the process and have a significant simultaneous influence on it.

Abstract Socio-technical transformations towards low-carbon energy systems are on the way in developed countries. Conversely, developing countries tend to be locked in fossil fuels and foster coal-based energy structures, emphasizing reliable and cost-effective energy provision and sidelining environmental concerns. In this study, we identified and analysed the predominant factors related to coal-based power generation in Bangladesh. We applied a mixed-method approach, initially conducting a systematic literature review and, subsequently, semi-structured expert interviews to identify and validate relevant factors. We then assessed their relative importance using an Analytical Hierarchy Process based on expert judgments. The results of this assessment reveal that socio-economic aspects and environmental issues scored highest, while technological aspects and sector regulations were considered to be less relevant for large-scale coal power implementation. We conclude that future energy policies created in Bangladesh will need to use appropriate legal instruments and address issues such as human displacement and resettlement, low levels of public acceptance, health hazards and environmental pollution. Participative policy frameworks should be deployed in coal plant projects, and active monitoring systems are necessary to reduce the negative consequences associated with increased electrification and energy consumption. To address foreseeable structural challenges, it furthermore will be crucial to explore sustainable alternatives.

Abstract Additional experimental data concerning the kinetics of Ni-Mo codeposition were obtained by investigating cathodic polarization using a rotating disc electrode. The Ni-Mo alloys were deposited from an ammonium citrate bath. The alloy deposition was controlled by activation in the case of low values of the cathode potential and by diffusion in the case of higher values. The hydrogen discharge was found to be diffusion controlled. The inductive influence of nickel results in depolarization of the reduction of molybdenum which cannot be deposited separately. An increase in the disc rotation speed caused an increase in the maximum cathode efficiency and in the molybdenum content of the alloy.

In this paper a novel approach to accommodate distributed generation resources in the power distribution system is discussed to reduce the peak power demand. Demand dispatch is the capability of aggregate and precisely control individual loads on command. The novel implemented approach in this work is the demand dispatch to demand response. The dispatch algorithms in regularity base are used for controllable loads which can be turned on and off with unnoticeable interruption where the load is forecasted and it is dispatched accordingly by using distributed generation resources and controllable loads, thereby it helps to reduce peak demand. Multi-Agent System (MAS) is consisting a group of agents which are capable of perceived environment that they are located and act on it by communicating with each other to achieve the goals. Therefore a MAs has been adopted to manage the demand dispatch simulation. Load has forecasted in MATLAB and MAS has programmed in ZEUS utilize the forecasted load data to dispatch the load in such a way so as to reduce the peak demand. The agents are located at demand aggregator level, zone level and DG level. They communicate to dispatch the load properly based on resources and load availability.

This manuscript presents performed laboratory studies and the analysis of the impact of current shunt values used in the differential connection on the wideband metrological performance of inductive current transformers. Moreover, a comparison of the accuracy of wideband and 50 Hz-type inductive current transformers in the specified frequency range from 50 Hz to 5 kHz is presented. The main factor which may influence the wideband accuracy of inductive current transformers is the phenomenon of self-generation. This causes rapid changes in the accuracy, and simultaneously causes the most positive and the most negative values of current error and phase displacement. To evaluate the metrological performance in the differential measurement setup for higher harmonics of the distorted current, a digital acquisition board was used. Obtained results show that if proper values of current shunt resistance are chosen, such devices may be used to evaluate the wideband accuracy of inductive current transformers. The results indicate that the typical units designed for the transformation of sinusoidal current with a frequency of 50 Hz can achieve a comparable metrological performance to that of the wideband inductive current transformer.

For economic reasons, expansions of transmission networks are based on a compromise between capital cost and security of power system operation. At the same time, the power system must withstand typical highly likely contingencies. Various emergency state control systems, also called special protections, prevent emergencies following less likely contingencies. This paper describes overloads emergency state control (OLEC) used for the alleviation of overload in transmission networks near a power plant. Such control uses the functions of automated power reduction of generating units and has been implemented for a large steam power plant. The OLEC presented here uses different methods of generation curtailment for steam generation units. A case study illustrates the efficiency of the proposed control method.

Abstract Coal gasification is accompanied with formation of tars that cause equipment problems and have to be removed from the raw gas. Our previous studies proved that nickel supported ceria-zirconia catalyst (Ni/CZ) reveals high activity towards decomposition of toluene and 1-methylnaphthalene (1-MN) via steam reforming reaction (SR). However, the components of the raw gas from coal gasification (i.e. H2, CO, CO2 and CH4) may influence the performance of Ni/CZ catalyst. The influence of particular components of the raw gas on catalyst performance during SR of model tar compounds have been studied and discussed in this paper. It has been found that H2 and CO addition to the steam reforming feed drastically decreases the activity of Ni/CZ catalyst, whereas CO2 presence enhances conversion of toluene and 1-MN mixture owing to the occurrence of dry reforming reaction (DR). It has also been observed that methane, which is present in the raw gas from coal gasification consumes partly both the H2O and CO2, causing some decrease in conversion of model tar compounds. The influence of contact time (tc) on hydrocarbons conversion and the participation of (DR) have been examined. As was observed, lower contact times lead to decrease in hydrocarbons conversion in SR, making the same participation of DR more pronounced than for higher tc values. This work proves that Ni/CZ catalyst can be used for removal of tarry compounds via the catalytic hot gas cleaning of the raw gas form coal gasification.