• Energy Research
• 2016-2025close
• PL close
• UA close
• KG close
• Energies close

The paper presents an experimental study on the formation process of burden surface texture on the blast furnace throat and its influence on the radial distribution of gas flow. The study was performed with the application of blast furnaces equipped with a bell-type charging device using radio-isotope means for the control of burden surface texture (profile) and burden surface level, i.e., gamma locators for burden surface texture. The study was carried out under the conditions of an operating blast furnace in an iron and steel plant using a unique GEOTAPS system for automated control of geometric and temperature parameters of burden material surface on the blast furnace throat. The influence of the surface texture on the gas flow distribution was also investigated. The possibility of a self-stabilization effect for burden surface texture and gas flow in an operating blast furnace under suitable conditions was experimentally proven. As a result of the experimental study performed, four ways of energy-saving technology implementation were determined for the control of blast furnace melting based on the data on the burden surface texture and previously unknown regularities of surface layer formation of burden material on the throat of an operating blast furnace with a bell-type charging device. The main idea of the paper is the development of automated control for the radial distribution of burden material and gas flow using actual or predicted surface texture parameters as important intermediate factors that both describe the process and have a significant simultaneous influence on it.

This manuscript presents performed laboratory studies and the analysis of the impact of current shunt values used in the differential connection on the wideband metrological performance of inductive current transformers. Moreover, a comparison of the accuracy of wideband and 50 Hz-type inductive current transformers in the specified frequency range from 50 Hz to 5 kHz is presented. The main factor which may influence the wideband accuracy of inductive current transformers is the phenomenon of self-generation. This causes rapid changes in the accuracy, and simultaneously causes the most positive and the most negative values of current error and phase displacement. To evaluate the metrological performance in the differential measurement setup for higher harmonics of the distorted current, a digital acquisition board was used. Obtained results show that if proper values of current shunt resistance are chosen, such devices may be used to evaluate the wideband accuracy of inductive current transformers. The results indicate that the typical units designed for the transformation of sinusoidal current with a frequency of 50 Hz can achieve a comparable metrological performance to that of the wideband inductive current transformer.

Energy efficiency is an increasingly important dimension of household appliances, which is why they are labeled to indicate their energy consumption. In 2020, the European Union countries changed the labeling system from the previous system: ranging from A+++ to D, to the new system: ranging from A to G, assuming it would be more transparent for the consumer. The aim of the study was to find out the extent to which consumers are aware of the new labeling system, and the impact that the new labels have (compared to the previous ones) on the perception of household appliances and consumer decision-making. For this purpose, the survey was conducted on a nationwide representative Polish sample (n = 1054). The research was partly experimental, where the same appliances were presented with new and previous energy labels. The results showed that currently most people do not identify the new energy classes. Furthermore, products with the new labels are perceived as being less energy efficient in comparison with products with the previous labels, which shows that there is some confusion among consumers in terms of the new energy efficiency labeling system.

The occurrence of surface discontinuous deformations in post-mining areas is currently a significant and important problem, due to both the frequency of their occurrence and the threat they pose to public safety. This paper presents the results of research concerning the possibility of sinkhole formation in the areas of abandoned mining excavations. For the purpose of assessing the condition of the rock mass disturbed by the existence of numerous mining excavations, electrical resistivity tomography investigations were carried out for the selected area where mining was undertaken in the past at shallow depths and many underground workings accessing the deposit exist. The sinkhole hazard was also analysed theoretically with a new original model based on the solution of A. Sałustowicz’s pressure arch theory.

Plate fin-tube heat exchangers are widely used in air conditioning and refrigeration systems and other industry fields. Various errors made in the manufacturing process can result in the formation of an air gap between the tube and fin. Several numerical simulations were carried out for a symmetric section of plate fin-tube heat exchanger to study the influence of air gap on heat transfer under periodic flow conditions. Different locations and sizes of an air gap spanning 1/2 circumference of the tube were considered for the range of airflow velocities. Velocity and temperature fields for cases with air gap were compared with ideal thermal contact cases. Blocking of heat flow by the gap leads to the reduction of heat transfer rate. Fin discontinuity in the front of the tube causes the smallest reduction of the heat transfer rate in comparison to the ideal tube-fin contact, especially for thin slits. The rear gap position is the worst in the smallest gap range. Therefore, reversing the flow direction can lead to up to a 15% heat transfer increase, if mainly the rear gaps are present. The introduction of a thin slit in the front of the tube leads to convective heat transfer enhancement, which should be further investigated.

The conversion of chemical energy contained in organic matter into electricity has become an object of interest for many scientists worldwide. This technology is used in microbial fuel cells (MFC). Apart from generating electrical energy, these cells can be used simultaneously for wastewater treatment. Although the technology is constantly being improved, currently functioning microbial fuel cells cannot provide appropriate output parameters to use on an industrial scale. One of the barriers is so-called extracellular electron transfer, which in turn depends on the electrode type used, its material, shape, and size. According to current literature, carbon, graphite, stainless steel, and ceramics are the most frequently used electrode materials. However, more and more often, scientists are turning to other, unusual materials, the production of which uses the newest technologies, and one of them is graphene. This material is modified in different ways and connected with other materials, and the results of this seem to be very promising. Scientists manage to get a higher level of extracellular electron transfer and, hence, higher output parameters of the whole system. This article describes chosen technologies and attempts made by scientists worldwide to use graphene in MFC and their results.

The 2030 zero-net emission target in the E.U. demands a significant improvement in the energy performance of the building stock. This study analyses the adoption of connected thermostats and Home energy-management system solutions (HEMS) as an effective means to tackle the residential energy footprint. It reviews the main features of HEMS systems in terms of technology, cross-study performances, and the obstacles to widespread adoption; the study adopts the case-study methodology to examine the impact on the Italian real estate stock at a regional level. A matrix of adoption scenarios assesses the potential benefits of global residential energy savings, weighted by local climatic variations, dimension, number of single dwellings, and average primary energy reduction per household. Results demonstrate that all adoption scenarios dramatically reduce residential energy consumption, outperforming the E.U. targets for Italy by 2030.

This paper aims to reconsider prosumers’ role in the power markets in the early stages of their decentralization, accounting for rising self-supply trends, security threats, and economic and regulatory barriers. The development of prosumerism envisages finding the ratio between retail market sales under the feed-in tariff and the net billing mechanism. Within the methodology section, the indicator of prosumer efficiency for electricity generation (EUR/kWh) is proposed based on average consumption/production ratios and consumption/delivery incentives. To support household prosumers, the mentioned incentives on the renewable energy market consider the self-supply cost of electricity, the levelized cost of electricity for small-scale green energy facilities (solar photovoltaic and wind), and transaction costs. This paper evaluates prosumer efficiency under three consumption/production ratio scenarios for Ukrainian households (self-consumption of 40%, 20%, and 100% of green electricity annually generated by a household and selling the leftovers via the feed-in tariff) for 2023. The gradual movement from fixed tariffs for households toward market-based prices promotes the emergence of new related market players and their consolidation in the market. Participation in the organized power market segments is relevant for day-ahead market prices above 130 EUR/MWh, disregarding the households’ tariff rate. The low price caps inhibit the prosumer’s participation in the market, while the transition from the feed-in tariff to net billing significantly promotes their development only under high price caps.