• Energy Research
• Closed Access close
• other engineering and technologies close
• GB close
• CA close
• RU close

Technical solutions for optimizing the flame aerodynamics and the design of tangentially arranged burners in a TGMP-314 boiler are proposed. The implementation of these solutions will make it possible to achieve more reliable operation of the boiler during fuel oil combustion, smaller amount of NOx emissions during the combustion of gas and fuel oil, and a somewhat lower air excess factor in the furnace.

Abstract A CFD modelling study has been undertaken to examine the co-firing of pulverised coal and biomass with particular regard to the burnout of the larger diameter biomass particles. Computations were based on a research combustion facility that replicates an industrial coal-fired power station. Three percent, by mass, of pinewood was blended with a bituminous UK coal, and the effects of the wood particle size and shape on the burnout of the combined wood and coal char were investigated. The effect of varying the devolatilisation and char combustion rate constants for the biomass component in the blend was also investigated. It was concluded that the combustion of small (200 μm) wood particles was rapid but the rate of combustion of larger particles was dependent on their composition, size, and shape.

The Severn Estuary has the world's second largest tide range and a barrage across the estuary, located just seawards of Cardiff in Wales and Weston in the South West England, has been proposed for over half a century, with the objective of extracting large amounts of tidal energy. A Severn Barrage, as previously proposed by the Severn Tidal Power Group (STPG), would be the largest renewable energy project for tidal power generation in the world, if built as proposed, and would generate approximately 5% of the UK's electricity needs. However, concerns have been raised over the environmental impacts of such a barrage, including potential increase in flood risk, loss of intertidal habitats etc. In addressing the challenges of maximizing the energy output and minimizing the environmental impacts of such a barrage, this research study has focused on using a Continental Shelf model, based on the modified Environmental Fluid Dynamics Code (EFDC) with a barrage operation module (EFDC_B), to investigate both the far and near field hydrodynamic impacts of a barrage for different operating scenarios. Three scenarios have been considered to simulate the Severn Barrage, operating via two-way generation and using different combinations of turbines and sluices. The first scenario consisted of 216 turbines and 166 sluices installed along the barrage; the second consisted of 382 turbines with no sluices; and the third consisted of 764 turbines and no sluices. The specification of the sluice gates and turbines are the same for all scenarios. The model results indicate that the third scenario has the best mitigating effects for the far-field and near-field flood risks caused by a barrage and produces the most similar results of minimum water depth and maximum velocity distributions to those obtained from simulating the natural conditions of the estuary, i.e. the current conditions. The results also show that the flow patterns around the barrage are closest to those for the existing natural conditions with minimal slight changes in the estuary. Thus, the results clearly indicate that the environmental impacts of a Severn Barrage can be minimized if the barrage is operated for two-way generation and under the third scenario. Although it appears that the energy output for the third scenario is less than that obtained for the other two scenarios, if very low head (VLH) turbines are used, then the third scenario could generate more energy as more turbines could be cited along the barrage structure. Therefore, the study shows that a Severn Barrage, operating in two-way generation and with 764 turbines (ideally VLH turbines), would be the best option to meet the needs of maximizing the energy output, but having a minimal impact on environmental changes in the estuary and far-field.

The solution of an electric circuit problem is only valid if the circuit elements have been validly modelled. The iron-cored coil is a common nonlinear circuit element, especially in power system circuits, where the iron core is laminated grain-oriented silicon-iron sheet. This paper attempts to show that eddy-current loss modelling in such a core is at least as important as hysteresis loss modelling, and demonstrates the accuracy of linear modelling of the eddy-current effect. If the circuit analyst has confidence in this complete model he can then decide which aspects of the model can be ignored with impunity when studying such circuit phenomena as ferroresonance, subharmonics and inrush current.

This paper analyzes the general issues of sectionalizing 110- and 220-kV distribution grids, including by current limiting. The results of calculations of transients in the event of various disturbances in the distribution network, taking into account the operation of emergency control devices, are presented. The results of comparative analysis of sectionalized and desectionalized distribution grids are presented. The authors hereof propose introducing a load increment safety factor to quantify how sectionalization or desectionalization could affect grid reliability. The paper further substantiates the need for accounting excess disturbances in sectionalized grids to design and implement measures to minimize accident-related losses. It analyzes the effectiveness of applying automatic load transfer (ALT) and draws recommendations on how to implement it.

The requirements of HVdc converter control are achieved by dicrital techniques with minimisation of circuit complexity. Feed-back control is applied to modification of the counting of clock pulses derived from the ac system by a phase-locked frequency multiplier. Symmetry of the derived firinc, oulses can be retained for all modes of operation with smooth transition from full rectification to full inversion.

Abstract A new formulation for the evaporation, flashing, condensation processes taking place in the effects of thermal desalination systems which simulates the operation of both forward and parallel/cross configurations is coupled with an exergo-economic model based on the SPECO method. The thermo-economic model uses accurate properties for the seawater, brine, pure water and vapour and is solved with an equation solver which does not require the development of a specific solution algorithm as in most previous studies. This flexible model is used to analyze the influence of the number of effects N and the temperature difference ΔT e between effects on the technical and economic performance of multi-effect desalination systems with ejector vapour compression. In particular, it is shown that the performance calculated by an earlier black-box approach is not attainable by technically and economically realistic systems. It is also shown that for each feed configuration and a given number of effects there exists an optimum value of ΔT e which minimizes the cost of the produced potable water. This last result forms the basis of a procedure that combines black-box results with the optimum value of ΔT e and can be used to select the appropriate system for any specific application.

Abstract This study develops a novel sustainability assessment methodology for energy systems using life-cycle emission factors and sustainability indicators. Here, the global warming and environmental impact dimensions of the sustainability assessment methodology are examined in detail. A comparative analysis shows that a wind-battery system produces fewer potential global warming, stratospheric ozone depletion, air pollution, and water pollution impacts compared to a gas-fired system. The wind-battery system generates 13% of the life-cycle GHG emissions and 22% of the life-cycle ozone-depleting substance emissions of a gas-fired power plant. Nitrous oxide contributes more than 90% of the stratospheric ozone depletion potential of gas-fired and wind-battery systems.

The temperature dependence of the electrical conductivity of the molten eutectic GdCl3(0.515)–KCl(0.485) containing up to 3.3 mol % gadolinium oxide is studied. The temperature dependences of the conductivity of the molten GdCl3–KCl–Gd2O3 system are approximated by second-order polynomials. The formation of gadolinium oxychlorides is confirmed by spectral studies of the solidified melt.