• Energy Research
• Open Access close
• Closed Access close

Abstract The amount of installed solar power in Finland is increasing as a result of decreasing photovoltaic (PV) system component prices. The growth is especially noticeable in residential systems, and ways to make PV electricity a more competitive choice for Finnish residents are studied. One of these ways is to decrease the solar PV electricity production costs by decreasing the investment costs by undersizing the inverter of the PV system. The objective of undersizing is to find the optimal array-to-inverter sizing ratio (AISR) where the ratio of the economic loss from the clipped energy to the economic gain from the decreased system investment achieved by an undersized inverter is lowest. In this paper, the economically most optimal AISRs are determined for different residential array sizes, orientations, and inclinations when operating in Finnish locations and conditions. Calculations for each inverter size are carried out by using recorded Finnish meteorological data and the current Finnish PV system cost distribution, and by analyzing existing 1-s resolution production measurement data of a Finnish PV system. It is concluded that it is necessary to use 1-s resolution data as the use of 1-h resolution production data would lead to more significant undersizing caused by the power clipping occurring within an hour. The optimal AISRs presented in this study are higher than the optimal ratios reported in previous studies for locations further south than Finland. This can be explained by the northern location of Finland, where the irradiance above Standard Test Conditions (STC) is lower than in central Europe, for example. This allows more significant undersizing as less energy is clipped even at higher ratios. In the case of south-oriented arrays in a 30° installation angle, the optimal AISRs for the 10 kW, 6 kW, and 3 kW inverters were 1.6, 1.8, and 2.08, respectively. Again, the AISRs for the southwest-southeast facade installations were 1.8, 1.9, and 2.17 for the inverters under study. They do not clip the produced energy as much as rooftop systems because their production is more evenly distributed throughout the day, yet they do not achieve as low production costs either. It is pointed out that if the PV self-consumption is optimized by using PV to heat water or batteries as a storage, limitation of the PV generation might not be the correct solution.

Abstract The purpose of this paper is to investigate the influence of blending methods on the co-gasification of petroleum coke and lignite with CO 2 using a thermogravimetric system at 0.1 MPa. The weight loss curves, XRD analysis, SEM images, BET specific surface area, were investigated. It was observed that petroleum coke shows a low reactivity because of the graphitic carbon structure, low catalyst content and small specific surface area. Blending with lignite can get a high reactivity. The co-gasification reactivity was significantly influenced by blending methods. Wet grinding is much effective than dry grinding. Long grinding time made lignite show greater BET specific area. And the sample in long grinding time has more association chances between petroleum coke and AAEM species. The co-gasification reactivity increases linearly with a rise of BET specific area.

Microalgae are recognized as a third generation feedstock for biofuel production due to their rapid growth rates and lignin-free characteristics. In this study, a lipid extracted microalgal biomass residues was used as the raw material to produce isoprene, α-pinene and β-pinene with an engineered E. coli strain. We adopted an optimal sulfuric acid hydrolysis method (1:7 ratio of solid to acid solution, 32% (w/v) concentration of sulfuric acid solution at 90 °C for 90 min) to efficiently convert holocellulose into glucose efficiently (6.37 g/L). Futhermore, we explored a novel detoxification strategy (phosphoric acid/calcium hydroxide) to remove inhibitors and notably acetic acid, furfural and 5-hydroxymethylfurfural (5-HMF) were reduced by 5.32%, different number given later 99.19% and 98.22%, respectively. Finally, the fermentation concentrations of isoprene (223.23 mg/L), α-pinene (382.21 μg/L) and β-pinene (17.4 mg/L) were achieved using the detoxified hydrolysate as the carbon source, equivalent to approximately 86.02%, 90.16% and 88.32% of those produced by the engineered E. coli strain fermented on pure glucose, respectively.

A major challenge in sustainability science is identifying targets that maximize ecosystem benefits to humanity while minimizing the risk of crossing critical system thresholds. One critical threshold is the biomass at which populations become so depleted that their population growth rates become negative—depensation. Here, we evaluate how the value of monitoring information increases as a natural resource spends more time near the critical threshold. This benefit emerges because higher monitoring precision promotes higher yield and a greater capacity to recover from overharvest. We show that precautionary buffers that trigger increased monitoring precision as resource levels decline may offer a way to minimize monitoring costs and maximize profits. In a world of finite resources, improving our understanding of the trade-off between precision in estimates of population status and the costs of mismanagement will benefit stakeholders that shoulder the burden of these economic and social costs.

AbstractWe have measured the effect of degradation on the I-V characteristics in APFO3:PCBM solar cells. The solar cell devices were subject to ambient air under simulated solar illumination. We found that the degradation resulted in a lowering of the fill factor and short circuit current while the open circuit voltage remained unchanged. In order to gain insight into what has caused the degraded I-V characteristics we have studied the active layer film using various techniques. We found clear spectral changes both in absorption and in photoinduced absorption spectroscopy correlated with increased carrier lifetimes and lowered mobility when comparing the degraded film with a pristine one. The results show a significant degradation of the active layer causing a lower fill-factor and short circuit current.

Abstract Three-dimensional (3D) metal halide perovskite solar cells (PSCs) have a power conversion efficiency that is now comparable with conventional silicon solar cells. For PSC applications to succeed in the market, long-term reliability under open-air conditions is essential. Recent experiments have shown that two-dimensional (2D) perovskites seem to exhibit good stability due to the presence of hydrophobic organic spacers, but 2D PSCs are incapable of generating and transporting a large amount of charge due to their extended optical bandgaps. Mixed dimensional perovskites with dimension lies between 2D and 3D recently became a promising candidate to sustain long-term stability and high performances concurrently to address this obstacle. The current research article presents the finding of simulation-based studies performed on novel device architecture consisting of ITO/Nb-Ti2O3/3D Perovskite/2D Perovskite/Spiro-OMeTAD/Au. Using optical simulation features of SCAPS, absorption of light is computed in the proposed device. The computational results show that the thickness of the 2D perovskite layer badly affects the solar cell parameters. A thin 2D perovskite behaves as a capped coating that avoids the deterioration of 3D perovskite in open-air environments. The effect of a multivalent defect in the 3D perovskite layer is mathematically modelled, and their impact on overall performance parameters are analyzed. The findings are compared to the same configuration results, except where the absorber layer’s multivalent defect has been substituted by a neutral defect of the same defect density of about (1011 cm−3). Results show that the multivalent defect leads to an underestimation of the efficiency by 4.2%.

Background: Climate change has been shown to be directly linked to multiple physiological sequelae and to impact health consequences. However, the impact of climate change on mental health globally, particularly among vulnerable populations, is less well understood. Objective: To explore the mental health impacts of climate change in vulnerable populations globally. Methods: We performed an integrative literature review to identify published articles that addressed the research question: What are the mental health impacts of climate change among vulnerable populations globally? The Vulnerable Populations Conceptual Model served as a theoretical model during the review process and data synthesis. Findings/Results: One hundred and four articles were selected for inclusion in this review after a comprehensive review of 1828 manuscripts. Articles were diverse in scope and populations addressed. Land-vulnerable persons (either due to occupation or geographic location), Indigenous persons, children, older adults, and climate migrants were among the vulnerable populations whose mental health was most impacted by climate change. The most prevalent mental health responses to climate change included solastalgia, suicidality, depression, anxiety/eco-anxiety, PTSD, substance use, insomnia, and behavioral disturbance. Conclusions: Mental health professionals including physicians, nurses, physician assistants and other healthcare providers have the opportunity to mitigate the mental health impacts of climate change among vulnerable populations through assessment, preventative education and care. An inclusive and trauma-informed response to climate-related disasters, use of validated measures of mental health, and a long-term therapeutic relationship that extends beyond the immediate consequences of climate change-related events are approaches to successful mental health care in a climate-changing world.

The effect of the combined application of nano-hydroxyapatite (NHAP) or nano-carbon black (NCB) on the phytoextraction of Pb by ryegrass was investigated as an enhanced remediation technique for soils by field-scale experiment. After the addition of 0.2% NHAP or NCB to the soil, temporal variation of the uptake of Pb in aboveground parts and roots were observed. Ryegrass shoot concentrations of Pb were lower with nano-materials application than without nano-materials for the first month. However, the shoot concentrations of Pb were significantly increased with nano-materials application, in particular NHAP groups. The ryegrass root concentrations of Pb were lower with nano-materials application for the first month. These results indicated that nano-materials had significant effects on stabilization of lead, especially at the beginning of the experiment. Along with the experimental proceeding, phytotoxicity was alleviated after the incorporation of nano-materials. The ryegrass biomass was significantly higher with nano-materials application. Consequently, the Pb phytoextraction potential of ryegrass significantly increased with nano-materials application compared to the gounps without nano-materials application. The total removal rates of soil Pb were higher after combined application of NHAP than NCB. NHAP is more suitable than NCB for in-situ remediation of Pb-contaminated soils. The ryegrass translocation factor exhibited a marked increase with time. It was thought that the major role of NHP and NBA might be to alleviate the Pb phytotoxicity and increase biomass of plants.