• Energy Research
• other engineering and technologies close
• 13. Climate action close
• CN close
• ES close

Wind characteristics (e.g., mean wind speed, gust factor, turbulence intensity and integral scale, etc.) are quite scattered in different measurement conditions, especially during typhoon and/or hurricane processes, which results in the structural engineer ambiguously determining the wind parameters in wind-resistant design of buildings and structures in cyclone-prone regions. In tropical cyclones (including typhoons and hurricanes), the inconsistent wind characteristics may be in part ascribed to the complex flow structure with the coexistence of both mechanical and convective turbulence in the boundary layer of tropical cyclones. Another significant contribution to the scattered wind characteristics is due to various measurement conditions (e.g., terrain exposure and height) and data processing schemes (e.g., averaging time). The removal of the inconsistency in the field-measurement system may offer a more rational comparison of measured wind data from various observation platforms, and hence facilitates a better identification scheme of the wind characteristics to guide the urban planning design and wind-resistant design of buildings and structures. In this study, an analytical framework was firstly proposed to eliminate the potential observation-related effects in wind characteristics and then the wind characteristics of seven field measured tropical cyclones (four typhoons and three hurricanes) were comparatively investigated. Specifically, field measurements of wind characteristics were converted to a standard reference station with a roughness length of 0.03 m, observation duration of 10 min for mean wind and averaging time of 3 s for gusty wind at a 10 m height. The differences of the measured wind characteristics between the typhoons and hurricanes were highlighted. The standardized turbulent wind characteristics under the analytical framework for typhoons and hurricanes were compared with the corresponding recommendations in standard of American Society of Civil Engineers (ASCE 7-10) and Architectural Institute of Japan Recommendations for Loads on Buildings (AIJ-RLB-2004).

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

Abstract This paper presented a novel method of dissipating solar photovoltaic heat based on the technology of micro-heat-pipe array and the utilization of photovoltaic-cell waste heat. This novel technology solved the problems of low PV electrical efficiency and thermal failure caused by high cell temperature, greatly increased the comprehensive utilization efficiency of solar energy, and extended the service life of photovoltaic modules. One-year experiments were conducted to investigate the electrical and thermal performance of a forced-circulation, household-type photovoltaic/thermal system based on micro-heat-pipe array in Beijing, China. Test results showed that on the four typical days in different seasons, the average electrical efficiencies were 13.76%, 11.92%, 13.71%, and 14.65%; the average thermal efficiencies were 31.62%, 33.07%, 24.99%, and 17.24%; and the average total efficiencies were 45.38%, 44.99%, 38.70%, 31.89%, respectively. The system met the demand of power supply on sunny days and the demand of hot water between March and November, except in cloudy days. These experimental results can provide basis and reference for practical applications of the system.

[EN]A systematic approach is developed for the conceptual optimal design of biomethane production via carbon capture. A hybrid heuristic-mathematical procedure is proposed to determine the optimal technology and operating conditions. The heuristic step consists of a literature-based screening of the available technologies. After the prescreening stage, the technologies selected are amine absorption, pressure swing adsorption (PSA), and membrane separation. The mathematical stage is composed of two steps. First, different alternatives for each technology are modeled based on first principles and rules of thumb. These models are used to select the optimal configuration for each process considered. Second, a superstructure model for biomethane production is developed integrating the pre-selected upgrading technologies to select the optimal process, as well as to determine the optimal operating conditions. Four waste sources are analyzed: cattle manure, swine manure, municipal food waste, and sludge. The results suggest that the best amine is diethanolamine (DEA), the best membrane material is the polyimide, and the suggested zeolite is 13X among the ones studied. Finally, among the three technologies, the overall results show that carbon capture using a PSA system using zeolite 13X results in lower production and investment costs, but very close to the use of membranes. The results indicate that food waste shows the lowest production cost for biomethane 0.36 €/Nm3, due to the largest organic matter content, whereas the investment costs are 67 M€, considering a biogas production rate of 0.035 kg of biomethane per kg of waste and the processing of 311 kt/yr of food waste. Credits or incentives are still needed for biomethane to be competitive with fossil natural gas. Junta de Castilla y León y USAL

Abstract In this study, we develop indices for the overall technical efficiency (OTE) and energy-saving target ratio (ESTR) using data envelopment analysis (DEA) to calculate the relative efficiency and energy-saving potential of 30 provinces in China from 1997 to 2014. The results are as follows: (1) the OTE of China is 79.187%, indicating that there is 20.813% potential for improvement. The OTE exhibits decreasing efficiency values from the coastal areas to the inland areas and has clear geographical relationships. The average values of OTE in the east, midland and west are 0.932, 0.694 and 0.703. Theoretically, the total energy savings of CE, HE, ME and BE are 11080.60PJ, 5124.71PJ, 4729.24PJ and 6797.39PJ. (2) Regarding CE, HE, ME and BE, the provinces with the highest comprehensive ranks are Henan, Shanxi, Shaanxi, and Gansu, which simultaneously have the greatest energy-saving potentials and energy-saving targets. (3) The HE has the largest average ESTR of 38.357% and the values for BE, CE, and ME are 25.759%, 23.874%, and 22.143%, respectively. The CE category is the greatest in total energy savings (40.171%), which is followed by BE (24.150%), HE (18.384%), and ME (17.293%).

Abstract Transportation de-carbonization is a complex problem involving the economy, population, technology and environment. Implementing the pathway simulation based on systematic methods will help to optimize the transportation sustainability plan. This study’s key motivation is that earlier research ignored the relationship between driving factors and the transmission process. To quantitatively identify the path and process of emission reduction, a hybrid system dynamics STIRPAT-SD model is proposed to explore the transportation optimization’s de-carbonization ability. This study fully considers the composition of elements and subsystems based on the STIRPAT theoretical model and visually shows the system’s feedback relationship. Transportation structural and technical optimization scenarios are set to identify the threshold reduction paths. It is found these optimization strategies have significant de-carbonization effects. And transportation structure policy has the highest de-carbonization efficiency, the emission intensity decreased by 9.1% under the TSS2 scenario (Transportation structure scenario). This study proposes a novelty model combining dynamic simulating processes with a significantly theoretical model to improve simulation and factor composition accuracy. And the joint scenario setting identifies the most effective de-carbonization pathway and clarifies the threshold of all possible pathways. Research findings can effectively track, test, predict the achievement of policy goals, and provide policy optimization references for the sustainable development related to the transportation system in practice.

China’s research on and specific implementation of energy saving for buildings are mainly concentrated in urban areas, but according to 2016 statistics, the rural population accounts for 42.65% of the total population, so rural housing has considerable energy-saving potential. However, the degree of attention to the energy consumption of rural houses needs to be improved. Regarding the research on and implementation of passive energy-saving strategies for residences, compared with centralized urban high-rise residences, rural residences mainly have independent courtyards, with a flexible layout and easier transformation. In this study, a system that uses the common cold lanes in traditional villages and buildings’ exterior walls was constructed, and the indoor spaces of courtyard buildings in southern Shaanxi were completely passively cooled in summer. This system can be completely separated from the supply of artificial energy by relying on the accumulation and buoyancy effects of air in patios and cold lanes and the hot-pressure ventilation in buildings to cool the buildings and greatly improve indoor ventilation efficiency. As the building is ventilated and cooled, the air wall formed in the system can effectively prevent direct contact between the outdoor and indoor temperatures and reduce the impact of thermal wall radiation on the interior. In previous studies on the passive design of courtyard houses, scholars considered the effect of thermal wall radiation on indoor temperature in simulations. Therefore, in this study, we also separately calculated whether to consider the difference between the situation with and without wall heat radiation (WHR) when simulating thermal conversion. The final results show that when the cooling system was adopted, the annual cooling load of the whole building was 4786.494 kW·h without WHR. However, with WHR, the cooling load reduction was 2989.128 kW·h, a difference of 1797.336 kW·h.

Abstract In this paper, coupled governing equations were proposed to simulate three-dimensional heat conduction and moisture transport in the nuclear waste repository. Because there will be a large temperature gradient near inner and outer boundaries of the bentonite buffer layer, and the heat driven moisture transport is introduced in the governing equation of moisture transport. By applying the Fourier and Laplace transforms, the governing equations were converted to the Bessel equations, and the Laplace-domain solutions to temperature and moisture distributions were derived through the inverse Fourier transform. The reliability of the proposed solutions was verified through comparative analysis with the line heat source model. These analytical solutions were applied to obtain the evolutions of temperature field and moisture distribution near the waste canister. Finally, a sensitivity study was performed to analyze the effects of relevant parameters on the heat driven moisture transport.