• Energy Research
• other engineering and technologies close
• 7. Clean energy close
• 11. Sustainability close
• 15. Life on land close
• AU close
• FI close

Microalgae have tremendous potential for producing liquid renewable fuel. Many methods for converting microalgae to biofuel have been proposed; however, an economical and energetically feasible route for algal fuel production is yet to be found. This paper presents a review on the comparison of the most promising conversion pathways of microalgae to liquid fuel: hydrothermal liquefaction (HTL), wet extraction and non-destructive extraction. The comparison is based on important assessment parameters of product quality and yield, nutrient recovery, GHG emissions, energy and the cost associated with the production of fuel from microalgae, in order to better understand the pros and cons of each method. It was found that the HTL pathway produces more oil than the wet extraction pathway; however, higher concentrations of unwanted components are present in the HTL oil produced. Less nutrients (N and P) can be recovered in HTL compared to wet extraction. HTL consumes more fossil energy and generates higher GHG emissions than wet extraction, while the production cost of fuel from HTL pathway is lower than wet extraction pathway. There is considerable uncertainty in the comparison of the energy consumption and economics of the HTL pathway and the wet extraction pathway due to different scenarios analysed in the assessment studies. To be able to appropriately compare methodologies, the conversion methods should be analysed from growth to upgradation of oil utilising sufficiently similar assumptions and scenarios. Based on the data in available literature, wet oil extraction is the more appropriate system for biofuel production than HTL. However, the potential of alternative extraction/conversion technologies, such as, non-destructive extraction, need to be further assessed.

Short-term load forecasting is an essential instrument in power system planning, operation and control. Many operating decisions are based on load forecasts, such as dispatch scheduling of generating capacity, reliability analysis, and maintenance planning for the generators. Overestimation of electricity demand will cause a conservative operation, which leads to the start-up of too many units or excessive energy purchase, thereby supplying an unnecessary level of reserve. On the contrary, underestimation may result in a risky operation, with insufficient preparation of spinning reserve, causing the system to operate in a vulnerable region to the disturbance. In this paper, semi-parametric additive models are proposed to estimate the relationships between demand and the driver variables. Specifically, the inputs for these models are calendar variables, lagged actual demand observations and historical and forecast temperature traces for one or more sites in the target power system. In addition to point forecasts, prediction intervals are also estimated using a modified bootstrap method suitable for the complex seasonality seen in electricity demand data. The proposed methodology has been used to forecast the half-hourly electricity demand for up to seven days ahead for power systems in the Australian National Electricity Market. The performance of the methodology is validated via out-of-sample experiments with real data from the power system, as well as through on-site implementation by the system operator.

Abstract With promising benefits such as traffic emission reduction, traffic congestion alleviation, and parking problem solving, Electric Vehicle (EV)-sharing systems have attracted large attentions in recent years. Different from other business modes, customers in sharing economy systems are usually price sensitive. Therefore, it is possible to shift the usage of shared EVs through a well-designed Dynamic Pricing Scheme (DPS), with the objective of maximizing the system operator's total profit. In this study, we propose a novel DPS for a large-scale EV-sharing network to address the EV unbalancing issue and satisfy the vehicle-grid-integration (VGI) service based on accurate station-level demand prediction. The proposed DPS is formulated as a complex optimization problem, which includes two Price Adjustment Level (PAL) decision variables for every origin-destination pair of stations. The two PALs are employed to affect the EV-sharing demand and travel time between each station pair, respectively. Physical and operational constraints from both EV demand and VGI service aspects are also included in the proposed model. Two case study are conducted to validate the effectiveness of the proposed method.

The performance capabilities of an axially laminated anisotropic rotor (ALA) in a high-speed synchronous reluctance motor (SynRM) were studied. A 12 kW ALASynRM was designed as an alternative to a high-speed induction motor (IM) with a solid rotor. The electromagnetic design was implemented taking into account possible issues related to the new manufacturing methods, which require thicker rotor layers than in a typical ALA. The ALASynRM shows a higher efficiency than the corresponding IM with a smooth or slitted solid rotor equipped with copper end rings. To verify the design method, a prototype IM with a smooth solid rotor was built and tested. In the analysis, it was found that, similar to IMs, in an ALASynRM a considerable part of losses takes place in the rotor despite the absence of slip-related losses in the SynRM. The distribution of eddy current losses in the ALA rotor is significantly uneven. The torque ripple in the ALASynRM is considerably larger than the corresponding ripple in IMs.

Abstract Intermittent renewable energy generation, which is determined by weather conditions, is increasing in power markets. The efficient integration of these energy sources calls for flexible participants in smart power grids. It has been acknowledged that a large, underutilized, flexible resource lies on the consumer side of electricity generation. Despite the recently increasing interest in demand flexibility, there is a gap in the literature concerning the incentives for consumers to offer their flexible energy to power markets. In this paper, we examine a virtual power plant concept, which simultaneously optimizes the response of controllable electric hot water heaters to solar power forecast error imbalances. Uncertainty is included in the optimization in terms of solar power day-ahead forecast errors and balancing power market conditions. We show that including solar power imbalance minimization in the target function changes the optimal hot water heating profile such that more electricity is used during the daytime. The virtual power plant operation decreases solar power imbalances by 5–10% and benefits the participating households by 4.0–7.5 € in extra savings annually. The results of this study indicate that with the number of participating households, while total profits increase, marginal revenues decrease.

Abstract This study demonstrates the possibility to use energy-cost optimal building designs based on life cycle approach. There is a lack of studies that cover the comprehensive assessment of both embodied energy (EE) and operational energy (OE) in a single optimization problem. The primary goal of the current study is to compare the optimized results of using OE+EE together and OE only. The optimization is performed on a case study building (townhouse) in Finland with three structural alternatives (i.e., reinforced concrete (RC); cross-laminated timber (CLT) and Steel). Different options for insulation thickness of external wall, roof, floor and window types were considered as decision variables as the scope of the present study is on building envelope. The objectives of the optimization are to minimize life cycle energy (LCE) and life cycle costs (LCC). The LCE difference between the most and least energy efficient solution on the pareto front is greater in case of the OE optimization, compared to OE+EE optimization. For all studied structures, the EE of the optimal solutions from OE+EE optimization ranges 16%–23% of LCE. Many of the non-dominated optimal solutions obtained from the OE+EE optimization shows a higher U-value for the building envelope components compared to the optimal solutions from the OE optimization. A relationship between both OE and EE with the overall thermal resistance of the building envelope is discussed to obtain a deeper understanding of such differences in U-value for the optimal solutions obtained from the OE+EE and OE optimization.

Abstract In this paper, we investigate distributed thermal-electrochemical modeling of a Lithium-Ion battery cell to include the effect of temperature distribution across the thickness of the cell as a first step to study the module level temperature distribution at high charging rates. Most recent works have focused on lumped thermal models for a Li-Ion cell which ignore any temperature differential across cell thickness. However, even a small temperature differential across cell thickness at the cell level can contribute to significant temperature differential in the thickness direction of stacked-up Li-Ion cells at the module level. Such temperature differential can potentially impact the battery charging control system, especially at high charging rates. Here, the thermal-electrochemical partial differential and algebraic equations for a Li-ion cell are solved via a spatial finite difference method. Simulation results show that the temperature differentials over the cell thickness at the cell level are not insignificant, particularly at high charging rates.

A model for pressurised steam/O2-blown fluidised-bed gasification of biomass with catalytic reforming of hydrocarbons and tars was developed using Aspen Plus simulation software. Seven main blocks were used to model the fluidised-bed gasifier and two for the catalytic reformer. Modelling blocks were complemented with FORTRAN subroutines to simulate the observed non-equilibrium behaviour of the process. The model was fitted with experimental data derived from a 0.5 MW scale test rig operated with crushed wood pellets and forest residues and was shown to be capable of predicting product gas composition from gasification of clean wood. A parametric analysis indicated that a significant improvement in the syngas efficiency could be achieved by rising the filtration temperature and reformer conversions. Other improvement possibilities include fuel drying and lower reforming temperature.

In recent years, sustainability concerns have gained increasing attention among countries and stakeholders worldwide. Towards the transition to sustainable rural development, the rural web framework (RWF) has become a consistent tool. Indicators from the RWF have been used to explore sustainable rural development for decision-making tasks, which improves the social, economic, and environmental performance of rural regions. However, the application of the RWF in studies is on the decline. Furthermore, there is a lack of literature reviews on the importance of the RWF and its relationship with different facets of sustainable development. We conducted a systematic literature review (SLR) (a) to explore how studies have used the RWF in the context of sustainable development and (b) to identify areas for further research. This study found that the RWF has mostly been used in developed countries, with fewer applications in developing countries. We suggest that there should be increased application of the RWF, particularly in developing countries, to broaden the rural web–sustainable development discourse and its relevance. This paper presents several areas where the indicators of the RWF can be applied to illustrate their relevance for policy decisions towards the achievement of the sustainable development goals (SDGs).