• Energy Research
• physical sciences close
• 7. Clean energy close
• 12. Responsible consumption close
• DE close
• FR close

AbstractThis paper presents an experimental assessment of a blended fatigue‐extreme controller for load control employing trailing edge flaps on a lab‐scale wind turbine. The controller blends between a repetitive model predictive controller that targets fatigue loads and a dedicated extreme load controller, which consists of a simple on‐off load control strategy. The Fatigue controller uses the flapwise blade root bending moments of the three blades as input sensors. The Extreme controller additionally uses on‐blade angle of attack and velocity measurements as well as acceleration measurements to detect extreme events and to allow for a fast reaction. The experiments are conducted on the Berlin Research Turbine within the large wind tunnel of the TU Berlin. In order to reproduce test cases with deterministic extreme wind conditions that follow industry standards, the wind tunnel was redesigned. The analyzed test cases are extreme direction change, extreme coherent gust, extreme operating gust and extreme coherent gust with direction change. The test cases are analyzed by on‐blade angle of attack and velocity measurements. The load control performance of the Blended controller is compared to the pure fatigue oriented and the pure extreme load controller. The Blended controller achieves a maximum flapwise blade root bending moment reduction of 23%, which is comparable to the reduction achieved by the Extreme controller.

In the search for a nontoxic replacement of the commonly employed CdS buffer layer for Cu(In,Ga)(S,Se) $_\mathrm{2}$ based solar cells, chemically deposited Zn(O,S) thin films are a most promising choice. In this paper, we address the usually slow deposition speed of Zn(O,S) in a newly developed ammonia-free chemical bath process, resulting in a deposition of 30 nm in 3 min with good homogeneity on 30 cm × 30 cm sized substrates. Solar cells with buffer layers prepared from this process match the efficiency of CdS reference cells. In a second step, we address the light-soaking post-treatment, still needed for maximum efficiencies. By addition of aluminum to the deposition process, the initial efficiencies can be increased slightly. With the addition of boron, the light-soaking post-treatment is rendered unnecessary, while maintaining high efficiencies above 15%, surpassing reference cells with CdS buffer.

Abstract This paper presents a comparison of commercially used German and Russian reactor pressure vessel steels from the positron annihilation spectroscopy (PAS) point of view, having in mind knowledge obtained also from other techniques from the last decades. The second generations of Russian RPV steels seems to be fully comparable with German steels and their quality enables prolongation of NPP operating lifetime over projected 40 years. The embrittlement of CrMoV steel is very low due to the dynamic recovery of radiation-induced defects at reactor operating temperatures.

Abstract In this work, we propose an acoustic energy harvesting metamaterial consisting of an array of silicone rubber pillars and a PZT patch deposited on an ultrathin aluminum plate with several holes based on locally resonant mechanism. The resonance is formed by removing four pillars, drilling a few of holes and attaching the PZT patch on the aluminum plate. The strain energy originating from an incident acoustic wave is centralized in the resonant region, and the PZT patch is used to convert the elastic strain energy into electrical power. Numerical analysis and experimental results show that the proposed millimeter-scale harvester with holes obviously improves the effect of acoustic energy harvesting while performing at the subwavelength scale for sonic low-frequency environment (less than 1150 Hz). In addition, the experimental results demonstrate that the maximum output voltage and power of the proposed acoustic energy harvesting system with 16 holes of 2 mm radius are 3 and 10 times higher than those without holes at the resonant mode for 2 Pa of incident acoustic pressure. Both the number and size of holes have a significant effect on the performance of acoustic energy harvesting. The advantages of the proposed structure are easy-to-machine and full of practicality, and it can be used in broad applications for low-frequency acoustic energy harvesting.

Abstract We single out the role of fully coherent induced gluon radiation on light hadron production in pA collisions. The effect has the same general features as for quarkonium production, however with a richer color structure as the induced radiation depends on the global color charge of the partonic subprocess final state. Baseline predictions for light hadron nuclear suppression in pPb collisions at the LHC are provided, taking into account only the effect of fully coherent energy loss, which proves to be of the same order of magnitude as gluon shadowing or saturation. This underlines the need to include fully coherent energy loss in phenomenological studies of hadron production in pA collisions.

This article investigates the impact of the back-surface-field (BSF) thickness variation within a local aluminum contact on the performance of passivated emitter and rear contact solar cells. A significant difference of BSF thickness between contact endings and the center of dash-shaped contacts is verified experimentally by a comprehensive statistical analysis using scanning electron microscopy. The impact of local BSF thickness differences on the cell performance is studied with 3-D technology computer-aided design (TCAD) device simulations. Several device parameters such as BSF thicknesses, the doping concentration in the BSF profile at rear contacts, or the metallized area fraction at the cell rear side are varied. Our simulation study shows that the open-circuit voltage is mainly affected by locally reduced BSF thicknesses, resulting in an efficiency loss up to 0.14%abs or 0.84%abs, respectively, if an area fraction of 1% or 20% within a local contact has reduced BSF thicknesses. This effect can be minimized either by reducing the metallized area fraction at the cell rear side or by increasing the doping concentration in the BSF profile at aluminum rear contacts. In addition, we demonstrate that the 3-D simulations can be approximated with 2-D simulations by applying a single doping profile with an average BSF thickness, calculated with the harmonic mean.

Abstract: The paper presents the results of the study on luminescence and electronic excitations in Li6Gd(BO3)3 single crystals. The optical and luminescence spectroscopy with a sub-nanosecond time resolution upon selective photoexcitation in the energy range from 3.0 to 650 eV was used to investigate in detail the luminescence of both the Gd3þ host ions and Ce3þ impurity ions as well as the processes of energy transfer between them. The intrinsic ultraviolet emission at 3.95–3.97 eV due to 6Pj-8S7=2 transitions in the Gd3þ host ion and the fast luminescence at 2.8–3.0 eV due to 5d-4f1 dipole-allowed transitions in the Ce3þ impurity ion were studied upon excitations hrough the intracenter, charge transfer, bandto-band, and inner-shell transitions. The specificity of the energy transfer upon excitation of photoluminescence in the energy range of absorption of the inner shells of different atoms of the crystal, as well as in the energy region of the giant resonance of 4d–4f transitions was revealed. On the basis of the experimental data, the bandgap Eg¼9.3 eV, the minimum energy of the 5d-4f1 and charge transfer transitions were determined. The expected positions of the ground states of the 4fn and 4fn15d levels of trivalent lanthanide ions as well as the 4fnþ1 and 4fn5d levels of divalent ions were calculated for all the lanthanide ions in Li6Gd(BO3)3 host crystal. Journal of luminescence 134, 113-125 (2013). doi:10.1016/j.jlumin.2012.09.002 Published by Elsevier, New York, NY [u.a.]