• Energy Research
• Restricted close
• 6. Clean water close
• 13. Climate action close
• Bioresource Technology close

The objective of the present work was: (i) to enable biodiesel production from acid waste lard; (ii) to study the esterification reaction as possible pre-treatment at different temperatures, catalyst amount and reaction times; (iii) to evaluate biodiesel quality according to EN 14214 after basic transesterification of the pre-treated fat; and (iv) to predict the impact of using such waste as raw material in mixture with soybean oil. Temperature and catalyst amount were the most important reaction conditions which mostly affected biodiesel quality, namely viscosity and purity. The selected pre-treatment conditions were 65 degrees C, 2.0 wt% H(2)SO(4) and 5 h, which allowed obtaining a product with a viscosity of 4.81 mm(2) s(-1) and a purity of 99.6 wt%. The proposed pre-treatment was effective to enable acid wastes as single raw materials for biodiesel production with acceptable quality; however, low yields were obtained (65 wt%). Alkali transesterification of a mixture of waste lard and soybean oil resulted in a product with a purity of 99.8 wt% and a yield of 77.8 wt%, showing that blending might be an interesting alternative to recycle such wastes. Also, because in addition to using conventional and relatively economical processes, some biodiesel properties depending on the raw material composition (such as the iodine value) might even be improved.

A techno-economic analysis for use of brewer's spent grains (BSG) on a biorefinery concept for the Brazilian case is presented. Four scenarios based on different levels of heat and mass integration for the production of xylitol, lactic acid, activated carbon and phenolic acids are shown. A simulation procedure using the software Aspen Plus and experimental yields was used. Such procedure served as basis for the techno-economic and environmental assessment according to the Brazilian conditions. Full mass integration on water and full energy integration was the configuration with the best economic and environmental performance. For this case, the obtained economic margin was 62.25%, the potential environmental impact was 0.012 PEI/kg products, and the carbon footprint of the processing stage represented 0.96 kg CO2-e/kg of BSG. This result served as basis to draw recommendations on the technological, economic and environmental feasibility for implementation of such type of biorefinery in Brazil.

The effect of substrate changes on the performance and microbial community of two-chamber microbial fuel cells (MFCs) was investigated in this study. The MFCs enriched with a single substrate (e.g., acetate, glucose, or butyrate) had different acclimatization capability to substrate changes. The MFC enriched with glucose showed rapid and higher power generation, when glucose was switched with acetate or butyrate. However, the MFC enriched with acetate needed a longer adaptation time for utilizing glucose. Microbial community was also changed when the substrate was changed. Clostridium and Bacilli of phylum Firmicutes were detected in acetate-enriched MFCs after switching to glucose. By contrast, Firmicutes completely disappeared and Geobacter-like species were specifically enriched in glucose-enriched MFCs after feeding acetate to the reactor. This study further suggests that the type of substrate fed to MFC is a very important parameter for reactor performance and microbial community, and significantly affects power generation in MFCs.

Biodiesel production from cotton-seed cake (CSC) and the pretreatment of the remaining biomass for dark fermentative hydrogen production was investigated. The direct conversion to biodiesel with alkali free fatty acids neutralization pretreatment and alkali transesterification resulted in a biodiesel with high esters content and physicochemical properties fulfilling the EN-standards. Blends of cotton-seed oil methyl esters (CME) and diesel showed an improvement in lubricity and cetane number. Moreover, CME showed good compatibility with commercial biodiesel additives. On the basis of conversion of the remaining CSC to sugars fermentable towards hydrogen, the optimal conditions included removal of the oil of CSC and pretreatment at 10% NaOH (w/w dry matter). The extreme thermophilic bacterium Caldicellulosiruptor saccharolyticus showed good hydrogen production, 84-112% of the control, from NaOH-pretreated CSC and low hydrogen production, 15-20% of the control, from the oil-rich and not chemically pretreated CSC, and from Ca(OH)2-pretreated CSC.

Carotenoids and phycobiliproteins have a high economic value, due to their wide range of biological and industrial applications. The implementation of strategies to increase their production, such as the application of two-phase light cultivation systems, can stimulate pigments production, increasing economic turnover. In this sense, Cyanobium sp. was grown in seven different two-phase white/red cultivation arrangements, varying the time of each light from 0 to 21 days. Biomass, photosynthetic activity, pigments profile and antioxidant capacity were measured along time. Red light increased photosynthetic activity and pigments content (ca. 1.8-fold), and the use of a two-phase cultivation system generally raised bioactivity and production of phytochemicals. Among the studied, the optimal cultivation condition was found with 10 days of white followed by 4 days of red light. The optimized growth led to a productivity of 137.4 ± 0.8 mg L-1 d-1 of biomass, 17.0 ± 0.2 mg L-1 d-1 of total phycobiliproteins and 4.5 ± 0.2 mg L-1 d-1 of carotenoids.

Six hydrothermal liquefaction experiments on Nannochloropsis salina and Spirulina platensis at subcritical and supercritical water conditions (220–375 °C, 20–255 bar) were carried out to explore the feasibility of extracting lipids from wet algae, preserving nutrients in lipid-extracted algae solid residue, and recycling process water for algae cultivation. GC–MS, elemental analyzer, FT-IR, calorimeter and nutrient analysis were used to analyze bio-crude, lipid-extracted algae and water samples produced in the hydrothermal liquefaction process. The highest bio-crude yield of 46% was obtained on N. salina at 350 °C and 175 bar. For S. platensis algae sample, the optimal hydrothermal liquefaction condition appears to be at 310 °C and 115 bar, while the optimal condition for N. salina is at 350 °C and 175 bar. Preliminary data also indicate that a lipid-extracted algae solid residue sample obtained in the hydrothermal liquefaction process contains a high level of proteins.

This investigation deals with the conversion of olive-mill wastewater (OMW) into several feedstocks suitable for hydrogen photo-production. The goal was reached by means of two sequential steps: (i) a pre-treatment process of stored-OMW for the removal of polyphenols, which made it possible to obtain several effluents, and (ii) a photo-fermentative process for hydrogen production by means of Rhodopseudomonas palustris sp. Four different adsorbent matrices (Azolla, granular active carbon, resin, and zeolite) were used to dephenolize stored-OMW. The four liquid fractions attained by using the above process created the same number of effluents, and these were diluted with water and then used for hydrogen photo-production. The maximum hydrogen production rate (14.31 mL/L/h) was attained with the photo-fermenter containing 25% of the effluent, which came from the pre-treatment of stored-OMW using granular active carbon. Using the carbon effluent as feedstock, the greatest light conversion efficiency of 2.29% was achieved.

Initial process studies carried out in Aspen Plus on an integrated thermochemical conversion process are presented herein. In the simulations, a hydrothermal liquefaction (HTL) plant is combined with a biogas plant (BP), such that the digestate from the BP is converted to a biocrude in the HTL process. This biorefinery concept offers a sophisticated and sustainable way of converting organic residuals into a range of high-value biofuel streams in addition to combined heat and power (CHP) production. The primary goal of this study is to provide an initial estimate of the feasibility of such a process. By adding a diesel-quality-fuel output to the process, the product value is increased significantly compared to a conventional BP. An input of 1000 kg h(-1) manure delivers approximately 30-38 kg h(-1) fuel and 38-61 kg h(-1) biogas. The biogas can be used to upgrade the biocrude, to supply the gas grid or for CHP. An estimated 62-84% of the biomass energy can be recovered in the biofuels.