• Energy Research
• 7. Clean energy close
• 6. Clean water close
• CN close
• BD close
• EC close

Abstract In a passive nuclear plant, the main control room must provide self-support functions for 72 h after an accident occurs. In this isolation mode, the heat generated by indoor occupants and equipment should be removed by using concrete walls that are 610 mm thick, and the finned ceiling made of concrete should maintain thermal habitability. However, the finned ceiling design has not been studied in normal buildings, and the cooling storage effect of plate-shaped fins is usually ignored during the design phase. In this study, a novel parametric resistance–capacitance thermal network is proposed to simulate the thermal performance of different fin-plate layout forms in the case of an accident. An experiment was conducted on a 1200 mm × 1200 mm × 610 mm fin-concrete module for 72 h to validate the model under constant air temperature conditions. Based on the model, multi-objective optimization was conducted to obtain optimal solution sets by using a radial basis function approximation model. The results show that the optimal performance indicators can be classified into unsteady and quasi-steady states, in which the dominant factors for heat transfer include the heat transfer area and the thickness of the finned plate, respectively. Further, the optimal solution sets for different convection and heating conditions obtained through an optimization process are used to design a fin layout based on actual temperature control demands and cooling storage.

In grounding fault of DC system, overvoltage will appear on equipment nodes in converter station. Due to different operation mode and equipment type, it is very different from overvoltage in AC system. Based on Shanghaimiao–Linyi​ ±800kV Ultra High Voltage Direct Current (UHVDC) transmission project, this paper studies the converter station overvoltage characteristics under the conditions of DC pole line grounding, DC bus grounding and converter transformer valve side grounding fault, then analyzes the influence of smoothing reactor, filter capacitor and grounding pole line on overvoltage. In grounding fault at DC pole line near the converter station, the maximum overvoltage occurs on the inductance of DC filter, which is 592.75kV; In grounding fault at the top of the high voltage converter valve, the maximum overvoltage occurs on the neutral bus, which is 272.17kV. Increasing the inductance or capacitance of the smoothing reactor and filter capacitor, shortening the length of grounding electrode wire can significantly reduce the amplitude and steepness of overvoltage. The calculation results provide a reference for the internal overvoltage suppression of DC converter station with layered access at the inverter side.

The steady-state phase distribution and the structural parameters have been taken as the input for the nuclear physics calculation in the ADS windowless spallation target. The distribution of the extreme large power density of the heat load is imported back as the source term in the energy equation. Then temperature distribution is obtained based on the flow process and heat transfer. The preliminary results show that the temperature distribution reaches the steady-state and its shape is like the broken wings of the butterfly. This is very important for the further design and optimization of the ADS windowless spallation target. So the two-way coupling simulation of the heat transfer process is successfully performed between the computational fluid dynamics and the nuclear physics simulation.

Abstract In this study, we develop indices for the overall technical efficiency (OTE) and energy-saving target ratio (ESTR) using data envelopment analysis (DEA) to calculate the relative efficiency and energy-saving potential of 30 provinces in China from 1997 to 2014. The results are as follows: (1) the OTE of China is 79.187%, indicating that there is 20.813% potential for improvement. The OTE exhibits decreasing efficiency values from the coastal areas to the inland areas and has clear geographical relationships. The average values of OTE in the east, midland and west are 0.932, 0.694 and 0.703. Theoretically, the total energy savings of CE, HE, ME and BE are 11080.60PJ, 5124.71PJ, 4729.24PJ and 6797.39PJ. (2) Regarding CE, HE, ME and BE, the provinces with the highest comprehensive ranks are Henan, Shanxi, Shaanxi, and Gansu, which simultaneously have the greatest energy-saving potentials and energy-saving targets. (3) The HE has the largest average ESTR of 38.357% and the values for BE, CE, and ME are 25.759%, 23.874%, and 22.143%, respectively. The CE category is the greatest in total energy savings (40.171%), which is followed by BE (24.150%), HE (18.384%), and ME (17.293%).

Abstract Transportation de-carbonization is a complex problem involving the economy, population, technology and environment. Implementing the pathway simulation based on systematic methods will help to optimize the transportation sustainability plan. This study’s key motivation is that earlier research ignored the relationship between driving factors and the transmission process. To quantitatively identify the path and process of emission reduction, a hybrid system dynamics STIRPAT-SD model is proposed to explore the transportation optimization’s de-carbonization ability. This study fully considers the composition of elements and subsystems based on the STIRPAT theoretical model and visually shows the system’s feedback relationship. Transportation structural and technical optimization scenarios are set to identify the threshold reduction paths. It is found these optimization strategies have significant de-carbonization effects. And transportation structure policy has the highest de-carbonization efficiency, the emission intensity decreased by 9.1% under the TSS2 scenario (Transportation structure scenario). This study proposes a novelty model combining dynamic simulating processes with a significantly theoretical model to improve simulation and factor composition accuracy. And the joint scenario setting identifies the most effective de-carbonization pathway and clarifies the threshold of all possible pathways. Research findings can effectively track, test, predict the achievement of policy goals, and provide policy optimization references for the sustainable development related to the transportation system in practice.

As a relatively mature technology, biomass molded fuel (BMF) is widely used in distributed and centralized heating in China and has received considerable government attention. Although many BFM incentive policies have been developed, decreased domestic traditional fuel prices in China have caused BMF to lose its economic viability and new policy recommendations are needed to stimulate this industry. The present study built a regionalized net present value (NPV) model based on real production process simulation to test the impacts of each policy factor. The calculations showed that BMF production costs vary remarkably between regions, with the cost of agricultural briquette fuel (ABF) ranging from 86 US dollar per metric ton (USD/t) to 110 (USD/t), while that of woody pellet fuel (WPF) varies from 122 USD/t to 154 USD/t. The largest part of BMF’s cost composition is feedstock, which accounts for up 50%–60% of the total; accordingly a feedstock subsidy is the most effective policy factor, but in consideration of policy implementation, it would be better to use a production subsidy. For ABF, the optimal product subsidy varies from 26 USD/t to 57 USD/t among different regions of China, while for WPF, the range is 36 USD/t to 75 USD/t. Based on the data, a regional BMF development strategy is also proposed in this study.

The wind power forecasting error restricts the benefit of the wind farm in the electricity market. Considering the cooperation of wind power bidding and energy storage system (ESS) operation with uncertainty, this paper proposes a coordinated bidding/operation model for the wind farm to improve its benefits in the electricity market. The maximum entropy based deep reinforcement learning (RL) algorithm, Soft Actor-Critic (SAC) is used to construct the model. The maximum entropy framework enables the designed agent to explore various optimal possibilities, which means the learned coordinated bidding/operation strategy is more stable considering the forecasting error. Particularly, penalty terms are introduced into the benefit function to relax the constraints and improve the convergency. The case study illustrates that the learned policy can effectively improve the wind farm benefit while ensuring robustness.

Test systems are important tools and benchmark for power system research. Currently, there is a lack of standard test systems for modern transmission expansion planning (TEP) research, especially under high variable renewable energy (VRE) penetrations. This paper describes a 38-bus test system named the HRP-38 system dedicated to TEP. “HRP” stands for high renewable penetration. The objective of establishing such a system is to provide a consistent platform for different TEP methods to be tested and compared. The test system considers high VRE penetration of more than 30% energy share, which will be an important feature in many power systems in the future. Both AC and DC candidate lines are given to provide sufficient transmission planning alternatives. The complexity of the test system is well balanced considering calculation tractability and the ability to test the performance of the TEP planning model. The network topology, generation mix, and load characteristics are described in detail. Year-round time series of VRE (wind power and PV) output and load curves for each bus are provided to facilitate a detailed evaluation of the transmission grid configuration under high VRE penetration. Finally, three benchmark results with different optimization targets are provided for the HRP-38 system.

Rapid urbanization combined with high economic growth, industrialization, and changes in socio-economic conditions increase the quantity of municipal solid waste. Cities located in South-Asia are facing serious issues due to waste, with countries like India, Bangladesh, and Pakistan top of the list of bad waste management. The increasing generation of solid waste and also the improper management of waste in Bangladesh leads to environmental degradation. Current waste management practice in Bangladesh is so weak that day by day it is harming the climate and creating a lot of unwanted situations. This research consists of an examination of the current administrative measures and presents another proposition for the executive cycle to decrease ecological contamination. The research study aims to decrease the amount of waste being dumped into municipal sanitary landfill sites & converting the waste into energy which is both financially and environmentally suitable by involving unemployed people in the management system. The results of this study will give an idea of how waste can be utilized as a resource and how this resource can be a capital good as well as how the local level problems can be solved by taking some strategies and making our environment suitable for future generations.